1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
|
/*
VGA Output
Outputs a red and white leaf to VGA. It should run most VGA monitors
at 640x480, though it does not follow the timing spec very
carefully. Real twisted or shielded wires, proper grounding, and not
doing this on a breadboard are recommended (but it seems to work ok
without).
SerialUSB and SysTick are disabled to get rid of the most frequently
occurring interrupts (which mess with timing). This means that you
have to use perpetual bootloader mode or the reset button to flash
new programs.
How to wire this to a VGA port:
D6 via ~200ohms to VGA Red (1)
D7 via ~200ohms to VGA Green (2)
D8 via ~200ohms to VGA Blue (3)
D11 to VGA VSync (14) (swapped?)
D12 to VGA HSync (13) (swapped?)
GND to VGA Ground (5)
GND to VGA Sync Ground (10)
See also:
- http://pinouts.ru/Video/VGA15_pinout.shtml
- http://www.epanorama.net/documents/pc/vga_timing.html
Created 20 July 2010
By Bryan Newbold for LeafLabs
This code is released with no strings attached.
*/
// FIXME: generalize for Native and Mini
#include "wirish.h"
// Pinouts -- you also must change the GPIO macros below if you change
// these
#define VGA_R 6 // STM32: A8
#define VGA_G 7 // STM32: A9
#define VGA_B 8 // STM32: A10
#define VGA_V 11 // STM32: A6
#define VGA_H 12 // STM32: A7
// These low level (and STM32 specific) macros make GPIO writes much
// faster
#define ABSRR ((volatile uint32*)0x40010810)
#define ABRR ((volatile uint32*)0x40010814)
#define RBIT 8 // (see pinouts)
#define GBIT 9
#define BBIT 10
#define VGA_R_HIGH *ABSRR = BIT(RBIT)
#define VGA_R_LOW *ABRR = BIT(RBIT)
#define VGA_G_HIGH *ABSRR = BIT(GBIT)
#define VGA_G_LOW *ABRR = BIT(GBIT)
#define VGA_B_HIGH *ABSRR = BIT(BBIT)
#define VGA_B_LOW *ABRR = BIT(BBIT)
#define ON_COLOR BIT(RBIT)
#define OFF_COLOR (BIT(RBIT) | BIT(GBIT) | BIT(BBIT))
// set has priority, so clear every bit and set some given bits:
#define VGA_COLOR(c) (*ABSRR = c | \
BIT(RBIT+16) | BIT(GBIT+16) | BIT(BBIT+16))
#define VGA_V_HIGH *ABSRR = BIT(6)
#define VGA_V_LOW *ABRR = BIT(6)
#define VGA_H_HIGH *ABSRR = BIT(7)
#define VGA_H_LOW *ABRR = BIT(7)
void isr_porch(void);
void isr_start(void);
void isr_stop(void);
void isr_update(void);
uint16 x = 0; // X coordinate
uint16 y = 0; // Y coordinate
uint16 logo_y = 0; // Y coordinate, mapped into valid logo index (for speed)
bool v_active = true; // Are we in the image?
const uint8 x_max = 16;
const uint8 y_max = 18;
uint32 logo[y_max][x_max] = {
{0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,},
{0,0,0,0,0,0,1,1,1,0,0,0,0,0,0,0,},
{0,0,0,0,0,1,0,0,0,1,0,0,0,0,0,0,},
{0,0,0,0,1,0,0,1,0,0,1,0,0,0,0,0,},
{0,0,0,1,0,0,0,1,0,0,0,1,0,0,0,0,},
{0,0,1,0,0,0,0,1,0,0,0,0,1,0,0,0,},
{0,0,1,0,0,1,0,1,0,1,0,0,1,0,0,0,},
{0,1,0,0,0,0,1,1,1,0,0,0,0,1,0,0,},
{0,1,0,1,0,0,0,1,0,0,0,1,0,1,0,0,},
{1,0,0,0,1,0,0,1,0,0,1,0,0,0,1,0,},
{1,0,0,0,0,1,0,1,0,1,0,0,0,0,1,0,},
{1,0,0,0,0,0,1,1,1,0,0,0,0,0,1,0,},
{0,1,0,0,0,0,0,1,0,0,0,0,0,1,0,0,},
{0,0,1,1,0,0,0,1,0,0,0,1,1,0,0,0,},
{0,0,0,0,1,1,1,0,1,1,1,0,0,0,0,0,},
{0,0,0,0,0,0,1,0,1,0,0,0,0,0,0,0,},
{0,0,0,0,0,0,1,1,1,0,0,0,0,0,0,0,},
{0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,}, };
HardwareTimer timer(4);
void setup() {
// Setup our pins
pinMode(BOARD_LED_PIN, OUTPUT);
pinMode(VGA_R, OUTPUT);
pinMode(VGA_G, OUTPUT);
pinMode(VGA_B, OUTPUT);
pinMode(VGA_V, OUTPUT);
pinMode(VGA_H, OUTPUT);
digitalWrite(VGA_R, LOW);
digitalWrite(VGA_G, LOW);
digitalWrite(VGA_B, LOW);
digitalWrite(VGA_H, HIGH);
digitalWrite(VGA_V, HIGH);
// Fill the logo array with color patterns corresponding to its
// truth value. Note that we could get more tricky here, since
// there are 3 bits of color.
for (int y = 0; y < y_max; y++) {
for (int x = 0; x < x_max; x++) {
logo[y][x] = logo[y][x] ? ON_COLOR : OFF_COLOR;
}
}
// This gets rid of the majority of the interrupt artifacts;
// there's still a glitch for low values of y, but let's not worry
// about that. (Probably due to the hackish way vsync is done).
SerialUSB.end();
systick_disable();
// Configure
timer.pause(); // while we configure
timer.setPrescaleFactor(1); // Full speed
timer.setMode(TIMER_CH1, TIMER_OUTPUT_COMPARE);
timer.setMode(TIMER_CH2, TIMER_OUTPUT_COMPARE);
timer.setMode(TIMER_CH3, TIMER_OUTPUT_COMPARE);
timer.setMode(TIMER_CH4, TIMER_OUTPUT_COMPARE);
timer.setOverflow(2287); // Total line time
timer.setCompare(TIMER_CH1, 200);
timer.attachInterrupt(TIMER_CH1, isr_porch);
timer.setCompare(TIMER_CH2, 300);
timer.attachInterrupt(TIMER_CH2, isr_start);
timer.setCompare(TIMER_CH3, 2170);
timer.attachInterrupt(TIMER_CH3, isr_stop);
timer.setCompare(TIMER_CH4, 1); // Could be zero, I guess
timer.attachInterrupt(TIMER_CH4, isr_update);
timer.setCount(0); // Ready...
timer.resume(); // Go!
}
void loop() {
toggleLED();
delay(100);
// Everything happens in the interrupts!
}
// This ISR will end horizontal sync for most of the image and
// setup the vertical sync for higher line counts
void isr_porch(void) {
VGA_H_HIGH;
y++;
logo_y = map(y, 0, 478, 0, y_max);
// Back to the top
if (y >= 523) {
y = 1;
logo_y = 0;
v_active = true;
return;
}
// Other vsync stuff below the image
if (y >= 492) {
VGA_V_HIGH;
return;
}
if (y >= 490) {
VGA_V_LOW;
return;
}
if (y >= 479) {
v_active = false;
return;
}
}
// This is the main horizontal sweep
void isr_start(void) {
// Skip if we're not in the image at all
if (!v_active) {
return;
}
// Start Red
VGA_R_LOW;
VGA_R_HIGH;
// For each "pixel", go ON_COLOR or OFF_COLOR
for (x = 0; x < 16; x++) {
// setting the color several times is just an easy way to
// delay, so the image is wider. if you only do the following
// once, you'll be able to make the logo array bigger:
VGA_COLOR(logo[logo_y][x]);
VGA_COLOR(logo[logo_y][x]);
VGA_COLOR(logo[logo_y][x]);
VGA_COLOR(logo[logo_y][x]);
VGA_COLOR(logo[logo_y][x]);
VGA_COLOR(logo[logo_y][x]);
}
}
// End of the horizontal line
void isr_stop(void) {
if (!v_active) {
return;
}
VGA_R_LOW;
VGA_G_LOW;
VGA_B_LOW;
}
// Setup horizonal sync
void isr_update(void) {
VGA_H_LOW;
}
__attribute__((constructor)) void premain() {
init();
}
int main(void) {
setup();
while (true) {
loop();
}
return 0;
}
|