aboutsummaryrefslogtreecommitdiffstats
path: root/docs/source/hardware/maple-ret6.rst
blob: 06dcaff6ef2f60faa9b9ad14e02119187a002a23 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
.. highlight:: sh

.. _maple-ret6:

Maple RET6 Edition
==================

.. contents:: Contents
   :local:

Technical Specifications
------------------------

    * MCU: **STM32F103RET6**, a 32-bit ARM Cortex M3 microprocessor
    * Clock Speed: **72 MHz**
    * Operating Voltage: 3.3V
    * Input Voltage (recommended): 3V-12V
    * 39 Digital I/O Pins (:ref:`GPIO <gpio>`)
    * 16 Analog Input pins, 12 bit **ADC** resolution (:ref:`ADC <adc>`)
    * 15 **PWM** pins at 16-bit resolution (:ref:`PWM <pwm>`)
    * Dedicated **USB** port for programming and communications (:ref:`USB<usb>`)
    * External **JTAG** interface (:ref:`JTAG <jtag>`)
    * **512KB Flash** and **64KB SRAM**
    * 64 Channel nested vector interrupt handler (including external interrupt on GPIOs)
    * Integrated **SPI** (:ref:`SPI <spi>`)
    * Integrated **I2C** (:ref:`I2C <i2c>`)
    * 12 Channels of Direct Memory Access (**DMA**)
    * 3 **USART** and 2 **UART** devices (:ref:`USART <usart>`)
    * Six 4-channel and two basic **timers** (:ref:`Timers <timers>`)
    * Supplies up to 800mA @ 3.3v
    * Support for low power and sleep modes (<500uA)
    * Dimensions are 2.05″x2.1″

.. _maple-ret6-powering:

Powering the Maple RET6 Edition
-------------------------------

The Maple RET6 Edition's power source is determined by the header to
the left of the "LeafLabs" label on the silkscreen.  The RET6 Edition
can be powered from the barrel jack connector, USB, or a LiPo battery.
We ship the RET6 Edition with a jumper on the USB selector.  In order
to power it off of an alternative source, unplug the board, then move
the jumper to the desired selector before reconnecting power.

You can also power the Maple via the pin labeled "Vin" on the lower
header.  However, don't do this while simultaneously powering the
board from another source, or you could damage the it.

Using the Built-in Battery Charger
----------------------------------

The RET6 Edition has a built-in LiPo battery charger.  In order to use
it, put a jumper across the CHRG header on the power selection header
and across the USB, or EXT selectors, depending on whether you're
charging the battery via USB cable or barrel jack connector.  The LED
labeled CHRG will light up while the battery is being charged.  When
the battery is finished charging, the LED labeled DONE will also light
up.

.. _maple-ret6-gpios:

GPIO Information
----------------

The RET6 Edition features 38 ready-to-use general purpose input/output
(GPIO) pins for digital input/output, numbered ``D0`` through ``D37``.
These numbers correspond to the numeric values next to each header on
the Maple silkscreen.  More GPIOs (numbered ``D39``\ --``43``) are
available through use in combination with the
:ref:`lang-disabledebugports` function; see the :ref:`board-specific
debug pin constants <lang-board-values-debug>` for more information.

.. TODO [0.1.0] silkscreen pictures which expand abbreviations

.. _maple-ret6-pin-map-master:

Master Pin Map
^^^^^^^^^^^^^^

.. TODO [0.0.10] Update from base Maple information

This table shows the available functionality on every GPIO pin, by
peripheral type. The "STM32" column refers to the port and number that
the header is connected to on the microcontroller.  The "5V?" column
documents whether or not the pin is 5 volt tolerant.

.. csv-table::
   :header: "Pin", "STM32", ":ref:`ADC <adc>`", ":ref:`Timer <timers>`", ":ref:`I2C <i2c>`", ":ref:`UART <usart>`", ":ref:`SPI <spi>`", "5v?"

   "D0",  "PA3",  "ADC3",  "TIM2_CH4",     "-",          "USART2_RX",  "-",         "No"
   "D1",  "PA2",  "ADC2",  "TIM2_CH3",     "-",          "USART2_TX",  "-",         "No"
   "D2",  "PA0",  "ADC0",  "TIM2_CH1_ETR", "-",          "USART2_CTS", "-",         "No"
   "D3",  "PA1",  "ADC1",  "TIM2_CH2",     "-",          "USART2_RTS", "-",         "No"
   "D4",  "PB5",  "-",     "-",            "ISC1_SMBA",  "-",          "-",         "No"
   "D5",  "PB6",  "-",     "TIM4_CH1",     "I2C1_SCL",   "-",          "-",         "Yes"
   "D6",  "PA8",  "-",     "TIM1_CH1",     "-",          "USART1_CK",  "-",         "Yes"
   "D7",  "PA9",  "-",     "TIM1_CH2",     "-",          "USART1_TX",  "-",         "Yes"
   "D8",  "PA10", "-",     "TIM1_CH3",     "-",          "USART1_RX",  "-",         "Yes"
   "D9",  "PB7",  "-",     "TIM4_CH2",     "I2C1_SDA",   "-",          "-",         "Yes"
   "D10", "PA4",  "ADC4",  "-",            "-",          "USART2_CK",  "SPI1_NSS",  "No"
   "D11", "PA7",  "ADC7",  "TIM3_CH2",     "-",          "-",          "SPI1_MOSI", "No"
   "D12", "PA6",  "ADC6",  "TIM3_CH1",     "-",          "-",          "SPI1_MISO", "No"
   "D13", "PA5",  "ADC5",  "-",            "-",          "-",          "SPI1_SCK",  "No"
   "D14", "PB8",  "-",     "TIM4_CH3",     "-",          "-",          "-",         "Yes"
   "D15", "PC0",  "ADC10", "-",            "-",          "-",          "-",         "No"
   "D16", "PC1",  "ADC11", "-",            "-",          "-",          "-",         "No"
   "D17", "PC2",  "ADC12", "-",            "-",          "-",          "-",         "No"
   "D18", "PC3",  "ADC13", "-",            "-",          "-",          "-",         "No"
   "D19", "PC4",  "ADC14", "-",            "-",          "-",          "-",         "No"
   "D20", "PC5",  "ADC15", "-",            "-",          "-",          "-",         "No"
   "D21", "PC13", "-",     "-",            "-",          "-",          "-",         "No"
   "D22", "PC14", "-",     "-",            "-",          "-",          "-",         "No"
   "D23", "PC15", "-",     "-",            "-",          "-",          "-",         "No"
   "D24", "PB9",  "-",     "TIM4_CH4",     "-",          "-",          "-",         "Yes"
   "D25", "PD2",  "-",     "TIM3_ETR",     "-",          "-",          "-",         "Yes"
   "D26", "PC10", "-",     "-",            "-",          "-",          "-",         "Yes"
   "D27", "PB0",  "ADC8",  "TIM3_CH3",     "-",          "-",          "-",         "No"
   "D28", "PB1",  "ADC9",  "TIM3_CH4",     "-",          "-",          "-",         "No"
   "D29", "PB10", "-",     "-",            "I2C2_SCL",   "USART3_TX",  "-",         "Yes"
   "D30", "PB11", "-",     "-",            "I2C2_SDA",   "USART3_RX",  "-",         "Yes"
   "D31", "PB12", "-",     "TIM1_BKIN",    "I2C2_SMBA",  "USART3_CK",  "SPI2_NSS",  "Yes"
   "D32", "PB13", "-",     "TIM1_CH1N",    "-",          "USART3_CTS", "SPI2_SCK",  "Yes"
   "D33", "PB14", "-",     "TIM1_CH2N",    "-",          "USART3_RTS", "SPI2_MISO", "Yes"
   "D34", "PB15", "-",     "TIM1_CH3N",    "-",          "-",          "SPI2_MOSI", "Yes"
   "D35", "PC6",  "-",     "-",            "-",          "-",          "-",         "Yes"
   "D36", "PC7",  "-",     "-",            "-",          "-",          "-",         "Yes"
   "D37", "PC8",  "-",     "-",            "-",          "-",          "-",         "Yes"

.. TODO [0.0.10] Another table for the JTAG pins

Timer Pin Map
^^^^^^^^^^^^^

.. TODO [0.0.10] Add Timer 5,6,7,8 information

The following table shows what pins are associated with a particular
timer's capture/compare channels.

.. csv-table::
   :header: Timer, Ch. 1, Ch. 2, Ch. 3, Ch. 4
   :delim: |

   1 | D6  | D7  | D8  | -
   2 | D2  | D3  | D1  | D0
   3 | D12 | D11 | D27 | D28
   4 | D5  | D9  | D14 | D24

.. _maple-ret6-exti-map:

EXTI Line Pin Map
^^^^^^^^^^^^^^^^^

The following table shows which pins connect to which :ref:`EXTI lines
<external-interrupts-exti-line>` on the Maple RET6 Edition.

.. list-table::
   :widths: 1 1
   :header-rows: 1

   * - EXTI Line
     - Pins
   * - EXTI0
     - 2, 15, 27
   * - EXTI1
     - 3, 16, 28
   * - EXTI2
     - 1, 17, 25
   * - EXTI3
     - 0, 18
   * - EXTI4
     - 10, 19
   * - EXTI5
     - 4, 13, 20
   * - EXTI6
     - 5, 12, 35
   * - EXTI7
     - 9, 11, 36
   * - EXTI8
     - 6, 14, 37
   * - EXTI9
     - 7, 25, 28
   * - EXTI10
     - 8, 26, 29
   * - EXTI11
     - 30
   * - EXTI12
     - 31
   * - EXTI13
     - 21, 32
   * - EXTI14
     - 22, 33
   * - EXTI15
     - 23, 34

.. _maple-ret6-usart-map:

USART Pin Map
^^^^^^^^^^^^^

.. FIXME [0.0.10] UART4 and UART5 information

The Maple RET6 Edition has three serial ports (also known as a UARTs
or USARTs): ``Serial1``, ``Serial2``, and ``Serial3``. They
communicate using the pins summarized in the following table:

.. csv-table::
   :header: Serial Port, TX, RX, CK, CTS, RTS
   :delim: |

   ``Serial1`` | 7  | 8  | 6  | -  | -
   ``Serial2`` | 1  | 0  | 10 | 2  | 3
   ``Serial3`` | 29 | 30 | 31 | 32 | 33

Board-Specific Values
---------------------

.. TODO [0.0.10]

Stub.

Hardware Design Files
---------------------

The hardware schematics and board layout files are available in the
`Maple Github repository <https://github.com/leaflabs/maple>`_.  Other
than the processor used, the design files for the Maple RET6 edition
are identical to the Maple Rev 5, which are in the ``maple-r5``
subdirectory of the Maple repository.  A schematic for a JTAG adapter
suitable for use with Maple is available in the ``jtagadapter``
directory.

From the Github repository main page, you can download the entire
repository by clicking the "Download" button.  If you are familiar
with `git <http://git-scm.com/>`_, you can also clone the repository
at the command line with ::

    $ git clone git://github.com/leaflabs/maple.git

.. _maple-ret6-failure-modes:

Failure Modes
-------------

The following known failure modes apply to all Maple boards.  The
failure modes aren't design errors, but are easy ways to break or
damage your board permanently.

* **High voltage on non-tolerant pins**: not all header pins are 5V
  compatible; so e.g. connecting certain serial devices in the wrong
  way could over-voltage the pins.  The :ref:`pin-mapping master table
  <maple-ret6-pin-map-master>` details which pins are 5V-tolerant.

Errata
------

This section lists known issues and warnings for the Maple RET6 Edition.

* **DAC, UART4, UART5 GPIOs unavailable**: Pins related to the digital
  to analog converter (DAC) and UARTs 4 and 5 are not broken out to
  headers.  The RET6 Edition's hardware layout is identical to that of
  the Maple Rev 5, which wasn't designed for use with these
  STM32F103RET6-only peripherals.

Recommended Reading
-------------------

* STMicro documentation for STM32F103RE microcontroller:

    * `Datasheet
      <http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00191185.pdf>`_ (PDF)
    * `Reference Manual
      <http://www.st.com/stonline/products/literature/rm/13902.pdf>`_ (PDF)
    * `Programming Manual
      <http://www.st.com/stonline/products/literature/pm/15491.pdf>`_
      (PDF; assembly language and register reference)