aboutsummaryrefslogtreecommitdiffstats
path: root/support/openocd/debug_0.4.cfg
diff options
context:
space:
mode:
Diffstat (limited to 'support/openocd/debug_0.4.cfg')
-rw-r--r--support/openocd/debug_0.4.cfg75
1 files changed, 0 insertions, 75 deletions
diff --git a/support/openocd/debug_0.4.cfg b/support/openocd/debug_0.4.cfg
deleted file mode 100644
index 7d6982a..0000000
--- a/support/openocd/debug_0.4.cfg
+++ /dev/null
@@ -1,75 +0,0 @@
-# script for stm32
-
-interface ft2232
-ft2232_device_desc "Olimex OpenOCD JTAG"
-ft2232_layout olimex-jtag
-ft2232_vid_pid 0x15ba 0x0003
-
-if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
-} else {
- set _CHIPNAME stm32
-}
-
-if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
-} else {
- set _ENDIAN little
-}
-
-# jtag speed speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so ufse F_JTAG = 1MHz
-jtag_khz 1000
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config srst_only
-
-#jtag scan chain
-if { [info exists CPUTAPID ] } {
- set _CPUTAPID $CPUTAPID
-} else {
- # See STM Document RM0008
- # Section 30.6.3
- set _CPUTAPID 0x3ba00477
-}
-
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-if { [info exists BSTAPID ] } {
- # FIXME this never gets used to override defaults...
- set _BSTAPID $BSTAPID
-} else {
- # See STM Document RM0008
- # Section 29.6.2
- # Low density devices, Rev A
- set _BSTAPID1 0x06412041
- # Medium density devices, Rev A
- set _BSTAPID2 0x06410041
- # Medium density devices, Rev B and Rev Z
- set _BSTAPID3 0x16410041
- # High density devices, Rev A
- set _BSTAPID4 0x06414041
- # Connectivity line devices, Rev A and Rev Z
- set _BSTAPID5 0x06418041
-}
-jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
- -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \
- -expected-id $_BSTAPID4 -expected-id $_BSTAPID5
-
-
-set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME
-
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x5000 -work-area-backup 0
-
-flash bank bank0 stm32x 0x08000000 0x00020000 0 0 $_TARGETNAME
-
-proc nopforever {} {
- puts "Resetting the chip... Halting for debugger."
- reset halt
-}
-
-init
-nopforever