1 files changed, 0 insertions, 87 deletions
diff --git a/src/stm32lib/examples/USART/Smartcard/readme.txt b/src/stm32lib/examples/USART/Smartcard/readme.txt
deleted file mode 100755
index 615be2a..0000000
--- a/src/stm32lib/examples/USART/Smartcard/readme.txt
+++ /dev/null
@@ -1,87 +0,0 @@
-/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
-* File Name          : readme.txt
-* Author             : MCD Application Team
-* Version            : V2.0.1
-* Date               : 06/13/2008
-* Description        : Description of the USART Smartcard Example.
-********************************************************************************
-* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
-* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
-* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
-* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
-* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
-* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
-*******************************************************************************/
-
-Example description
-===================
-This example provides a description of how  to use the USART in Smartcard mode. 
-The example gives only the possibility to read the ATR and decode it into 
-predefined buffer.
-First, the code is waiting for an card insertion. If a card is detected through
-the EXTI Line interrupt (connected to the Smartcard detect pin), a reset signal
-is applied to the card through its reset pin.
-As response to this reset, the card transmit the ATR which will be stored in 
-predefined buffer. Once the ATR is received, it is decoded and stored in a specific
-structure (SC_A2R) and the card protocol type is stored in a variable.
-ATRDecodeStatus variable must be equal to 1 (PASSED) when the sequence succeed.
-
-The used Smartcard should be ISO7816-3 T=0 compatible.
-
-USART3 configured as follow:
-  - Word Length = 9 Bits
-  - 0.5 Stop Bit
-  - Even parity
-  - BaudRate = 12096 baud
-  - Hardware flow control disabled (RTS and CTS signals)
-  - Tx and Rx enabled
-  - USART Clock enabled
-  - USART CPOL: Clock is active low
-  - USART CPHA: Data is captured on the second edge 
-  - USART LastBit: The clock pulse of the last data bit is not output to 
-                   the SCLK pin
-
-
-Directory contents
-==================
-platform_config.h    Evaluation board specific configuration file
-stm32f10x_conf.h     Library Configuration file
-stm32f10x_it.h       Interrupt handlers header file
-stm32f10x_it.c       Interrupt handlers
-main.c               Main program
-
-
-Hardware environment
-====================
-This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
-boards and can be easily tailored to any other hardware.
-To select the STMicroelectronics evaluation board used to run the example, uncomment
-the corresponding line in platform_config.h file.
-
- + STM3210B-EVAL 
-    - Plug a Smartcard (ISO7816-3 T=0 compatible) into the dedicated Smartcard 
-      connector CN16.
- 
- + STM3210E-EVAL
-    - Plug a Smartcard (ISO7816-3 T=0 compatible) into  the dedicated Smartcard 
-      connector CN18.
-    - Make sure that Jumper 15 (JP15) and Jumper 16 (JP16) are fitted.
-
-  
-How to use it
-=============
-In order to make the program work, you must do the following :
-- Create a project and setup all your toolchain's start-up files
-- Compile the directory content files and required Library files :
-  + stm32f10x_lib.c
-  + stm32f10x_gpio.c
-  + stm32f10x_rcc.c
-  + stm32f10x_usart.c
-  + stm32f10x_nvic.c
-  + stm32f10x_flash.c
-  + stm32f10x_exti.c
-        
-- Link all compiled files and load your image into target memory
-- Run the example
-
-******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******