1 files changed, 0 insertions, 94 deletions
diff --git a/src/stm32lib/examples/USART/IrDA/Transmit/readme.txt b/src/stm32lib/examples/USART/IrDA/Transmit/readme.txt
deleted file mode 100755
index e5dd1e2..0000000
--- a/src/stm32lib/examples/USART/IrDA/Transmit/readme.txt
+++ /dev/null
@@ -1,94 +0,0 @@
-/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
-* File Name          : readme.txt
-* Author             : MCD Application Team
-* Version            : V2.0.1
-* Date               : 06/13/2008
-* Description        : Description of the USART IrDA Transmit Example.
-********************************************************************************
-* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
-* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
-* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
-* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
-* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
-* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
-*******************************************************************************/
-
-Example description
-===================
-This example provides a basic communication USART3 IrDA transmit mode. Five pins,
-configured in input floating mode, are used to select the byte to be send at 
-each pin state change. 
-
-These bytes are:
-  - 0x00 if no key pressed
-  - 0x01 if SEL pin state change
-  - 0x02 if RIGHT pin state change 
-  - 0x03 if LEFT pin state change 
-  - 0x04 if UP pin state change 
-  - 0x05 if DOWN pin state change 
-  
-USART3 configured as follow:
-   - BaudRate = 115200 baud  
-   - Word Length = 8 Bits
-   - One Stop Bit
-   - No parity
-   - Hardware flow control disabled (RTS and CTS signals)
-   - Receive and transmit enabled
-
-The USART IrDA example provides two IrDA program: transmitter&receiver and requires two boards
-to be able to run the full demonstration:
- - one board will act as IrDA transmitter
- - one board will act as IrDA receiver
-
-
-Directory contents
-==================
-platform_config.h    Evaluation board specific configuration file
-stm32f10x_conf.h     Library Configuration file
-stm32f10x_it.h       Interrupt handlers header file
-stm32f10x_it.c       Interrupt handlers
-main.c               Main program
-
-
-Hardware environment
-====================
-This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
-boards and can be easily tailored to any other hardware.
-To select the STMicroelectronics evaluation board used to run the example, uncomment
-the corresponding line in platform_config.h file.
-
- + STM3210B-EVAL 
-    - Use DOWN push-button connected to pin PD.14
-    - Use UP push-button connected to pin PD.08
-    - Use SEL push-button connected to pin PD.12
-    - Use RIGHT push-button connected to pin PE.00
-    - Use RIGHT push-button connected to pin PE.01                   
-    - Use an IrDA tranceiver connected to the USART3 Tx pin (U11 connector, JP5 
-      jumper must be fitted).
- 
- + STM3210E-EVAL
-    - Use DOWN push-button connected to pin PD.03
-    - Use UP push-button connected to pin PG.15
-    - Use SEL push-button connected to pin PG.07
-    - Use RIGHT push-button connected to pin PG.13
-    - Use RIGHT push-button connected to pin PG.14   
-    - Use an IrDA tranceiver connected to the USART3 Tx pin (U13 connector, JP21
-      and JP22 jumper must be fitted).
-  
-  
-How to use it
-=============
-In order to make the program work, you must do the following:
-- Create a project and setup all your toolchain's start-up files
-- Compile the directory content files and required Library files:
-  + stm32f10x_lib.c
-  + stm32f10x_gpio.c
-  + stm32f10x_rcc.c
-  + stm32f10x_usart.c
-  + stm32f10x_nvic.c
-  + stm32f10x_flash.c
-      
-- Link all compiled files and load your image into target memory
-- Run the example
-
-******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******