1 files changed, 0 insertions, 95 deletions
diff --git a/src/stm32lib/examples/TIM/ExtTrigger_Synchro/readme.txt b/src/stm32lib/examples/TIM/ExtTrigger_Synchro/readme.txt
deleted file mode 100755
index 78e8ace..0000000
--- a/src/stm32lib/examples/TIM/ExtTrigger_Synchro/readme.txt
+++ /dev/null
@@ -1,95 +0,0 @@
-/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
-* File Name          : readme.txt
-* Author             : MCD Application Team
-* Version            : V2.0.1
-* Date               : 06/13/2008
-* Description        : Description of the TIM ExTrigger_Synchro example.
-********************************************************************************
-* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
-* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
-* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
-* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
-* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
-* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
-*******************************************************************************/
-
-Example description
-===================
-
-This example shows how to synchronize TIM peripherals in cascade mode with an
-external trigger.
-In this example three timers are used:
-
-1/TIM2 is configured as Master Timer:
- - Toggle Mode is used
- - The TIM2 Enable event is used as Trigger Output 
- 
-2/TIM2 is configured as Slave Timer for an external Trigger connected to TIM2 TI2 pin 
-(TIM2 CH2 configured as input pin):
- - The TIM2 TI2FP2 is used as Trigger Input
- - Rising edge is used to enable and stop the TIM2: Gated Mode.
-  
-3/TIM3 is slave for TIM2 and Master for TIM4,
- - Toggle Mode is used
- - The ITR1(TIM2) is used as input trigger 
- - Gated mode is used, so start and stop of slave counter are controlled by the Master
-   trigger output signal(TIM2 enable event).
- - The TIM3 enable event is used as Trigger Output. 
-
-4/TIM4 is slave for TIM3,
- - Toggle Mode is used
- - The ITR2(TIM3) is used as input trigger
- - Gated mode is used, so start and stop of slave counter are controlled by the Master 
-trigger output signal(TIM3 enable event).
-
-The TIMxCLK is fixed to 72 MHZ, the Prescaler is equal to 2 so the TIMx clock counter
-is equal to 24 MHz.
-The Three Timers are running at: 
-TIMx frequency = TIMx clock counter/ 2*(TIMx_Period + 1) = 162.1 KHz.
-
-The starts and stops of the TIM2 counter are controlled by the external trigger.
-The TIM3 starts and stops are controlled by the TIM2, and the TIM4 starts and stops 
-are controlled by the TIM3.	 
-  
-
-Directory contents
-==================
-stm32f10x_conf.h  Library Configuration file
-stm32f10x_it.c    Interrupt handlers
-stm32f10x_it.h    Interrupt handlers header file
-main.c            Main program
- 
-
-Hardware environment
-====================
-This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
-boards and can be easily tailored to any other hardware.
-There is no need for any modification when switching between these two boards.
-
-- Connect an external trigger, with a frequency <= 40KHz, to the TIM2 CH2 pin (PA.01).
-  In this example the frequency is equal to 5 KHz.
-
-- Connect the:
-  - TIM2 CH1 (PA.00)
-  - TIM3 CH1 (PA.06)
-  - TIM4 CH1 (PB.06) 
-  pins to an oscilloscope to monitor the different waveforms.
-   
-  
-How to use it
-=============
-In order to make the program work, you must do the following:
-- Create a project and setup all your toolchain's start-up files
-- Compile the directory content files and required Library files:
-  + stm32f10x_lib.c
-  + stm32f10x_tim.c
-  + stm32f10x_gpio.c
-  + stm32f10x_rcc.c
-  + stm32f10x_nvic.c
-  + stm32ff10x_flash.c
-
-- Link all compiled files and load your image into target memory
-- Run the example
-
-
-******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******