1 files changed, 0 insertions, 72 deletions
diff --git a/src/stm32lib/examples/SPI/Simplex_Interrupt/readme.txt b/src/stm32lib/examples/SPI/Simplex_Interrupt/readme.txt
deleted file mode 100755
index 4f5d768..0000000
--- a/src/stm32lib/examples/SPI/Simplex_Interrupt/readme.txt
+++ /dev/null
@@ -1,72 +0,0 @@
-/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
-* File Name          : readme.txt
-* Author             : MCD Application Team
-* Version            : V2.0.1
-* Date               : 06/13/2008
-* Description        : Description of the SPI Simplex_Intrerrupt Example.
-********************************************************************************
-* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
-* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
-* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
-* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
-* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
-* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
-*******************************************************************************/
-
-Example description
-===================
-This example provides a description of how to set a communication between two
-SPIs in simplex mode and performs a data buffer transfer from Master to Slave 
-using TxE interrupt for master and RxNE interrupt for slave.
-
-Both SPIs are configured with 8bit data frame and a 9Mbit/s communication speed.
-SPI1 is configured to be a master transmitter and SPI2 as slave receiver. 
-The TxE interrupt is enabled for the master and the RxNE interrupt is enabled for
-the slave.
-
-Once both SPIs are enabled, first TxE interrupt is generated for the master
-and in its interrupt service routine the first data is sent from SPI1_Buffer_Tx. 
-Once this data is received by the slave a RxNE interrupt is generated and in the 
-routine this data is stored in the SPI2_Buffer_Rx.
-
-The same procedure is followed for the remaining SPI1_Buffer_Tx data.
-Once all data buffer are received by the slave the TxE interrupt is disabled.
-A comparison is done and TransferStatus gives the data transfer status where 
-it is PASSED if transmitted and received data are the same otherwise it is FAILED.
-
-
-Directory contents
-==================
-stm32f10x_conf.h     Library Configuration file
-stm32f10x_it.c       Interrupt handlers
-stm32f10x_it.h       Header for stm32f10x_it.c
-main.c               Main program
-
-
-Hardware environment
-====================
-This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
-boards and can be easily tailored to any other hardware.
-There is no need for any modification when switching between these two boards.
-
- - Connect SPI1 SCK pin (PA.05) to SPI2 SCK pin (PB.13)
- - Connect SPI1 MOSI pin (PA.07) to SPI2 MISO pin (PB.14)
-
-
-How to use it
-=============
-In order to make the program work, you must do the following :
-- Create a project and setup all your toolchain's start-up files
-- Compile the directory content files and required Library files :
-  + stm32f10x_lib.c
-  + stm32f10x_spi.c
-  + stm32f10x_rcc.c
-  + stm32f10x_gpio.c
-  + stm32f10x_nvic.c
-  + stm32f10x_flash.c
-    
-- Link all compiled files and load your image into target memory
-- Run the example
-
-
-******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******