1 files changed, 0 insertions, 75 deletions
diff --git a/src/stm32lib/examples/I2C/SMBus/readme.txt b/src/stm32lib/examples/I2C/SMBus/readme.txt
deleted file mode 100755
index 15e395a..0000000
--- a/src/stm32lib/examples/I2C/SMBus/readme.txt
+++ /dev/null
@@ -1,75 +0,0 @@
-/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
-* File Name          : readme.txt
-* Author             : MCD Application Team
-* Version            : V2.0.1
-* Date               : 06/13/2008
-* Description        : Description of the I2C SMBus mode example.
-********************************************************************************
-* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
-* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
-* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
-* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
-* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
-* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
-*******************************************************************************/
-
-Example description
-===================
-This example provides a description of how to send an ARP command from I2C1 to
-I2C2 in SMBus mode.
-
-After configuring the I2C1 and I2C2 as SMBus Host and Device, respectively, both
-I2Cs are enabled. The PEC calculation is enabled for both I2Cs.
-The ARP capability is enabled for the slave I2C2. Following the start condition
-generation, the master I2C1 sends the SMBus default header and I2C2 responds by
-setting its SMBDEFAULT flag. The master I2C1 then issues the "Prepare to ARP"
-command to the slave I2C2. PEC transfer is then enabled for both I2Cs, and the
-PEC value received on I2C2 is stored into the PEC_Value variable.
-
-A correct transmission leads to obtaining the following variable values:
-         - Status = 0x01 (the flag SMBDEFAULT has been set)
-         - ReceivedCommand = 0x01 (the Command value has been correctly received)
-         
-The communication clock speed is set to 200KHz.
-
-
-Directory contents
-==================
-stm32f10x_conf.h  Library Configuration file
-stm32f10x_it.c    Interrupt handlers
-stm32f10x_it.h    Interrupt handlers header file
-main.c            Main program
-
-
-
-Hardware environment
-====================
-This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
-boards and can be easily tailored to any other hardware.
-
- - Connect I2C1 SCL pin (PB.06) to I2C2 SCL pin (PB.10)
- - Connect I2C1 SDA pin (PB.07) to I2C2 SDA pin	(PB.11)
- - Check that a pull-up resistor is connected on one I2C SDA pin
- - Check that a pull-up resistor is connected on one I2C SCL pin
-
-Note: The pull-up resitors are already implemented on the STM3210B-EVAL and
-      STM3210E-EVAL evaluation boards.
-      
-
-How to use it
-=============
-In order to make the program work, you must do the following :
-- Create a project and setup all your toolchain's start-up files
-- Compile the directory content files and required Library files :
-  + stm32f10x_lib.c
-  + stm32f10x_i2c.c
-  + stm32f10x_rcc.c
-  + stm32f10x_nvic.c
-  + stm32f10x_gpio.c
-  + stm32f10x_flash.c
-    
-- Link all compiled files and load your image into target memory
-- Run the example
-
-
-******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******