1 files changed, 0 insertions, 71 deletions
diff --git a/src/stm32lib/examples/ADC/RegSimul_DualMode/readme.txt b/src/stm32lib/examples/ADC/RegSimul_DualMode/readme.txt
deleted file mode 100755
index ded3195..0000000
--- a/src/stm32lib/examples/ADC/RegSimul_DualMode/readme.txt
+++ /dev/null
@@ -1,71 +0,0 @@
-/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
-* File Name          : readme.txt
-* Author             : MCD Application Team
-* Version            : V2.0.1
-* Date               : 06/13/2008
-* Description        : Description of the ADC regular simultaneous dual mode Example.
-********************************************************************************
-* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
-* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
-* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
-* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
-* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
-* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
-*******************************************************************************/
-
-Example description
-===================
-This example describes how to use ADC1 and ADC2 in regular simultaneous dual mode.
-ADC1 is configured to convert channel14 and channel17 regular channels continuously.
-ADC2 is configured to convert channel11 and channel12 regular channels continuously.
-The connection between internal Vref and channel17 is enabled for ADC1.
-
-Once the regular channels conversion is started by software, channel14 is converted
-on ADC1 and channel11 is converted on ADC2 on the same time. The 32bits conversion 
-result is then stored on ADC1 DR register. The DMA will transfer this data which
-will be stored ADC_DualConvertedValueTab table. Consecutively to those conversion,
-channel17 is converted on ADC1 and channel12 on ADC2. The combined conversion
-result is also transfered by DMA to the same destination buffer. 
-
-The same procedure is repeated until the specified number of data to be transfered
-by DMA is reached.
-
-The ADC1 clock is set to 14 MHz.
-
-
-Directory contents
-==================
-stm32f10x_conf.h  Library Configuration file
-stm32f10x_it.c    Interrupt handlers
-stm32f10x_it.h    Interrupt handlers header file
-main.c            Main program
-
-
-Hardware environment
-====================
-This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
-boards and can be easily tailored to any other hardware.
-
- - Connect a known voltage, between 0-3.3V, to ADC Channel14 mapped on pin PC.04
-   (potentiometer RV1 on STM3210B-EVAL and STM3210E-EVAL boards),ADC Channel11 mapped 
-   on pin PC.01 and ADC Channel12 mapped on pin PC.02.
-   
-      
-How to use it
-=============
-In order to make the program work, you must do the following :
-- Create a project and setup all your toolchain's start-up files
-- Compile the directory content files and required Library files :
-  + stm32f10x_lib.c
-  + stm32f10x_adc.c
-  + stm32f10x_dma.c
-  + stm32f10x_gpio.c
-  + stm32f10x_rcc.c
-  + stm32f10x_nvic.c
-  + stm32f10x_flash.c
-    
-- Link all compiled files and load your image into target memory
-- Run the example
-
-
-******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******