blob: 950ac446487af9e44a44a6cfbb8041da046b2271 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
|
/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
* File Name : readme.txt
* Author : MCD Application Team
* Version : V2.0.1
* Date : 06/13/2008
* Description : Description of the TIM 7PWM_Output example.
********************************************************************************
* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
*******************************************************************************/
Example description
===================
This example shows how to configure the TIM1 peripheral to generate 7 PWM signals
with 4 different duty cycles.
TIM1CLK is fixed to 72 MHz, the TIM1 Prescaler is equal to 0 so the TIM1 counter
clock used is 72 MHz.
TIM1 frequency is defined as follow:
TIM1 frequency = TIM1CLK/(TIM1_Period + 1) = 17.57 KHz.
The TIM1 CCR1 register value is equal to 0x7FF, so the TIM1 Channel 1 and TIM1
Channel 1N generate a PWM signal with a frequency equal to 17.57 KHz
and a duty cycle equal to:
TIM1 Channel1 duty cycle = TIM1_CCR1 /( TIM1_Period + 1) = 50%.
The TIM1 CCR2 register value is equal to 0x5FF, so the TIM1 Channel 2 and TIM1
Channel 2N generate a PWM signal with a frequency equal to 17.57 KHz
and a duty cycle equal to:
TIM1 Channel2 duty cycle = TIM1_CCR2 / ( TIM1_Period + 1)= 37.5%.
The TIM1 CCR3 register value is equal to 0x3FF, so the TIM1 Channel 3 and TIM1
Channel 3N generate a PWM signal with a frequency equal to 17.57 KHz
and a duty cycle equal to:
TIM1 Channel3 duty cycle = TIM1_CCR3 / ( TIM1_Period + 1) = 25%.
The TIM1 CCR4 register value is equal to 0x1FF, so the TIM1 Channel 4
generate a PWM signal with a frequency equal to 17.57 KHz
and a duty cycle equal to:
TIM1 Channel4 duty cycle = TIM1_CCR4 / ( TIM1_Period + 1) = 12.5%.
The TIM1 waveform can be displayed using an oscilloscope.
Directory contents
==================
stm32f10x_conf.h Library Configuration file
stm32f10x_it.c Interrupt handlers
stm32f10x_it.h Interrupt handlers header file
main.c Main program
Hardware environment
====================
This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
boards and can be easily tailored to any other hardware.
Connect the TIM1 pins to an oscilloscope to monitor the different waveforms:
- TIM1_CH1 pin (PA.08)
- TIM1_CH1N pin (PB.13)
- TIM1_CH2 pin (PA.09)
- TIM1_CH2N pin (PB.14)
- TIM1_CH3 pin (PA.10)
- TIM1_CH3N pin (PB.15)
- TIM1_CH4 pin (PA.11)
How to use it
=============
In order to make the program work, you must do the following:
- Create a project and setup all your toolchain's start-up files
- Compile the directory content files and required Library files:
+ stm32f10x_lib.c
+ stm32f10x_tim.c
+ stm32f10x_gpio.c
+ stm32f10x_rcc.c
+ stm32f10x_nvic.c
+ stm32f10x_flash.c
- Link all compiled files and load your image into target memory
- Run the example
******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******
|