/* *****************************************************************************
* The MIT License
*
* Copyright (c) 2010 Perry Hung.
*
* Permission is hereby granted, free of charge, to any person obtaining a copy
* of this software and associated documentation files (the "Software"), to deal
* in the Software without restriction, including without limitation the rights
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
* copies of the Software, and to permit persons to whom the Software is
* furnished to do so, subject to the following conditions:
*
* The above copyright notice and this permission notice shall be included in
* all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
* THE SOFTWARE.
* ****************************************************************************/
/**
* @file exti.h
*
* @brief External interrupt control prototypes and defines
*/
#ifndef _EXTI_H_
#define _EXTI_H_
/* Notes:
*
* To generate the interrupt, the interrupt line should be configured and
* enabled. This is done by programming the two trigger registers with the
* desired edge detection and by enabling the interrupt request by writing a
* '1' to the corresponding bit in the interrupt mask register. When the
* selected edge occurs on the external interrupt line, an interrupt request is
* generated. The pending bit corresponding to the interrupt line is also set.
* This request is reset by writing a '1' in the pending register.
*
* Hardware interrupt selection:
* To configure the 20 lines as interrupt sources, use the following procedure:
* 1) Configure AFIO_EXTIICR[y] to select the source input for EXTIx external
* interrupt
* 2) Configure the mask bits of the 20 interrupt lines (EXTI_IMR)
* 3) Configure the trigger selection bits of the interrupt lines (EXTI_RTSR and EXTI_FTSR)
* 4) Configure the enable and mask bits that control the NVIC_IRQ channel mapped to the External
* Interrupt Controller (EXTI) so that an inerrupt coming from one of the 20 lines
* can be correctly acknowledged.
*
* AFIO clock must be on.
*
* RM0008, page 107: "PD0, PD1 cannot be used for external interrupt/event generation
* on 36, 48, 64-bin packages."
*
* ----------------------------------------------------------------------------
* Pin to EXTI Line Mappings:
* EXTI0 EXTI1 EXTI2 EXTI3 EXTI4
* ----------------------------------------------------------------------------
* D2/PA0 D3/PA1 D1/PA2 D0/A6/PA3 D10/A10/PA4
* D26/EXT7/PB0 D27/EXT8/PB1 D16/A2/PC2 D17/A3/PC3 D18/A4/PC4
* D14/A0/PC0 D15/PC1 D25/EXT5/PD2
*
* EXTI5 EXTI6 EXTI7 EXTI8 EXTI9
* ----------------------------------------------------------------------------
* D13/A13/PA5 D12/A12/PA6 D11/A11/PA7 D6/PA8 D7/PA9
* D4/PB5 D5/PB6 D9/PB7 D38/PB8 D23/EXT4/PB9
* D19/A5/PC5 D34/EXTI15/PC6 D35/EXT16/PC7 D36/PC8 D37/EXT18/PC9
*
* EXTI10 EXTI11 EXTI12 EXTI13 EXTI14
* ----------------------------------------------------------------------------
* D8/PA10 D29/EXT10/PB11 D30/EXTI1/PB12 D31/EXTI12/PB13 D32/EXT13/PB14
* D28/PB10 D20/EXTI1/PC13 D21/EXT2/PC14
* D25/PC10
*
* EXTI15
* ----------------------------------------------------------------------------
* D33/EXTI14/PB15
* D22/EXT3/PC15
*
*
* The 16 EXTI interrupts are mapped to 7 interrupt handlers.
*
* EXTI Lines to Interrupt Mapping:
* EXTI0 -> EXTI0
* EXTI1 -> EXTI1
* EXTI2 -> EXTI2
* EXTI3 -> EXTI3
* EXTI4 -> EXTI4
* EXTI[5-9] -> EXT9_5
* EXTI[10-15] -> EXT15_10
*
*
* */
#define NR_EXTI_CHANNELS 16
#define NR_EXTI_PORTS 4
#define NR_EXTI_MODES 3
#define EXTI_IMR 0x40010400 // Interrupt mask register
#define EXTI_EMR (EXTI_IMR + 0x04) // Event mask register
#define EXTI_RTSR (EXTI_IMR + 0x08) // Rising trigger selection register
#define EXTI_FTSR (EXTI_IMR + 0x0C) // Falling trigger selection register
#define EXTI_SWIER (EXTI_IMR + 0x10) // Software interrupt event register
#define EXTI_PR (EXTI_IMR + 0x14) // Pending register
#define AFIO_EVCR 0x40010000
#define AFIO_EXTICR1 (AFIO_EVCR + 0x08)
#define AFIO_EXTICR2 (AFIO_EVCR + 0x0C)
#define AFIO_EXTICR3 (AFIO_EVCR + 0x10)
#define AFIO_EXTICR4 (AFIO_EVCR + 0x14)
#define EXTI_RISING 0
#define EXTI_FALLING 1
#define EXTI_RISING_FALLING 2
#define EXTI0 0
#define EXTI1 1
#define EXTI2 2
#define EXTI3 3
#define EXTI4 4
#define EXTI5 5
#define EXTI6 6
#define EXTI7 7
#define EXTI8 8
#define EXTI9 9
#define EXTI10 10
#define EXTI11 11
#define EXTI12 12
#define EXTI13 13
#define EXTI14 14
#define EXTI15 15
#define EXTI_CONFIG_PORTA 0
#define EXTI_CONFIG_PORTB 1
#define EXTI_CONFIG_PORTC 2
#define EXTI_CONFIG_PORTD 3
#ifdef __cplusplus
extern "C"{
#endif
void exti_attach_interrupt(uint8, uint8, voidFuncPtr, uint8);
void exti_detach_interrupt(uint8);
#ifdef __cplusplus
} // extern "C"
#endif
#endif