.. highlight:: cpp .. _lang-serialusb: ``SerialUSB`` ============= Used for communication between the Maple board and a computer. .. contents:: Contents :local: Introduction ------------ In addition to three :ref:`serial ports `, the Maple's STM32 microprocessor includes a dedicated USB peripheral. This peripheral is used to emulate a regular serial port for use as a terminal. The emulated terminal is relatively slow; it is best for transferring data at regular serial speeds (kilobaud). Library access to the emulated serial port is provided through the ``SerialUSB`` object. You can mostly use ``SerialUSB`` as a drop-in replacement for ``Serial1``, ``Serial2``, and ``Serial3``. .. warning:: The ``SerialUSB`` functionality includes a 50 millisecond timeout for writes, and does not try to detect if the USB host is "really" connected, or just enumerated and initialized. This means that if you have a number of calls to one of the ``SerialUSB`` ``write()`` or ``print()`` functions in your code, and you are not monitoring ``SerialUSB`` on a computer, your program will run much slower than if it is being monitored or totally disconnected (run off of a battery). You can avoid this behavior by :ref:`deciphering the port status using the DTR and RTS line status ` (the behavior of these control lines is platform dependent and we no longer interpret them by default). Library Documentation --------------------- The ``SerialUSB`` object is an instance of the ``USBSerial`` class, which is documented in this section. This means that you can use any of these functions by writing ``SerialUSB.functionName(arguments...)``. For example, to print the message "hello, world!", you can write ``USBSerial.println("hello, world!")``. .. cpp:class:: USBSerial Emulated serial-over-USB class. ``SerialUSB`` is the predefined (singleton) instance. .. _lang-serialusb-begin: .. cpp:function:: USBSerial::begin() Set up the USB peripheral for emulated serial communication. The peripheral is configured this way by default; calling this function should only be necessary if you have disabled the peripheral using ``SerialUSB.end()``. .. _lang-serialusb-end: .. cpp:function:: USBSerial::end() Disables the USB peripheral. Note that using this function will terminate all USB communications between the Maple and the USB host; in particular, it implies that you won't be able to upload any new programs without resetting the board or using :ref:`perpetual bootloader mode `. .. cpp:function:: unsigned int USBSerial::available() Returns the number of bytes available for reading. .. _lang-serialusb-read: .. cpp:function:: unsigned char USBSerial::read() Returns the next available, unread character. If there are no available characters (you can check this with :cpp:func:`available `), the call will block until one becomes available. .. cpp:function:: USBSerial::print(unsigned char b) Print the given byte over the USB connection. .. cpp:function:: USBSerial::print(char c) Print the given character over the USB connection. 7-bit clean characters are typically interpreted as ASCII text. .. cpp:function:: USBSerial::print(const char *str) Print the given null-terminated string over the USB connection. .. cpp:function:: USBSerial::print(int n) Print the argument's digits over the USB connection, in decimal format. Negative values will be prefixed with a ``'-'`` character. .. cpp:function:: USBSerial::print(unsigned int n) Print the argument's digits over the USB connection, in decimal format. .. cpp:function:: USBSerial::print(long n) Print the argument's digits over the USB connection, in decimal format. Negative values will be prefixed with a ``'-'`` character. .. cpp:function:: USBSerial::print(unsigned long n) Print the argument's digits over the USB connection, in decimal format. .. cpp:function:: USBSerial::print(long n, int base) Print the digits of ``n`` over the USB connection, in base ``base`` (which may be between 2 and 16). The ``base`` value 2 corresponds to binary, 8 to octal, 10 to decimal, and 16 to hexadecimal. Negative values will be prefixed with a ``'-'`` character. .. cpp:function:: USBSerial::print(double n) Print ``n``, accurate to 2 digits after the decimal point. .. _lang-serialusb-println: .. cpp:function:: USBSerial::println(char c) Like ``print(c)``, followed by ``"\r\n"``. .. cpp:function:: USBSerial::println(const char *c) Like ``print(c)``, followed by ``"\r\n"``. .. cpp:function:: USBSerial::println(unsigned char b) Like ``print(b)``, followed by ``"\r\n"``. .. cpp:function:: USBSerial::println(int n) Like ``print(n)``, followed by ``"\r\n"``. .. cpp:function:: USBSerial::println(unsigned int n) Like ``print(n)``, followed by ``"\r\n"``. .. cpp:function:: USBSerial::println(long n) Like ``print(n)``, followed by ``"\r\n"``. .. cpp:function:: USBSerial::println(unsigned long n) Like ``print(n)``, followed by ``"\r\n"``. .. cpp:function:: USBSerial::println(long n, int base) Like ``print(n, b)``, followed by ``"\r\n"``. .. cpp:function:: USBSerial::println(double n) Like ``print(n)``, followed by ``"\r\n"``. .. cpp:function:: USBSerial::println() Prints ``"\r\n"`` over the USB connection. .. cpp:function:: USBSerial::write(unsigned char ch) Sends one character over the USB connection. This function is currently blocking, although nonblocking writes are a planned future extension. This is a low-level function. One of the ``print()`` or ``println()`` functions is likely to be more useful when printing multiple characters, when formatting numbers for printing, etc. .. cpp:function:: USBSerial::write(const char* str) Send the given null-terminated character string over the USB connection. This is a low-level function. One of the ``print()`` or ``println()`` functions is likely to be more useful when printing multiple characters, when formatting numbers for printing, etc. .. cpp:function:: USBSerial::write(void *buf, unsigned int size) Writes the first ``size`` bytes of ``buf`` over the USB connection. Each byte is transmitted as an individual character. This is a low-level function. One of the ``print()`` or ``println()`` functions is likely to be more useful when printing multiple characters, when formatting numbers for printing, etc. Examples -------- .. _lang-serialusb-safe-print: **Safe print**: This function should run smoothly and not block; the LED should blink at roughly the same speed whether being monitored, running from battery, or connected but not monitored. You may need to experiment with the DTR/RTS logic for your platform and device configuration. :: #define LED_PIN BOARD_LED_PIN void setup() { /* Set up the LED to blink */ pinMode(LED_PIN, OUTPUT); } void loop() { // LED will stay off if we are disconnected, and will blink // quickly if USB is unplugged (battery power, etc.). if(SerialUSB.isConnected()) { digitalWrite(LED_PIN, 1); } delay(100); // If this logic fails to detect if bytes are going to be read // by the USB host, then the println() take a long time, // causing a very slow LED blink. If the characters are // printed and read, the blink will only slow a small amount // when "really" connected, and will be fast fast when the // virtual port is only configured. if(SerialUSB.isConnected() && (SerialUSB.getDTR() || SerialUSB.getRTS())) { for(int i = 0; i < 10; i++) { SerialUSB.println(123456, BIN); } } digitalWrite(LED_PIN, 0); delay(100); }