From d9f2a93159df96eef0d8084b96df7268533177ff Mon Sep 17 00:00:00 2001 From: Perry Hung Date: Thu, 26 May 2011 20:13:09 -0400 Subject: openocd: Detect openocd version Small script to detect the openocd version and choose the appropriate debug/flash script for use with JTAG debugging. --- support/make/build-rules.mk | 2 +- support/openocd/debug_0.3.cfg | 75 ++++++++++++++++++++++++++++++++++ support/openocd/debug_0.4.cfg | 75 ++++++++++++++++++++++++++++++++++ support/openocd/flash.cfg | 89 ----------------------------------------- support/openocd/flash_0.3.cfg | 89 +++++++++++++++++++++++++++++++++++++++++ support/openocd/flash_0.4.0.cfg | 89 ----------------------------------------- support/openocd/flash_0.4.cfg | 89 +++++++++++++++++++++++++++++++++++++++++ support/openocd/run.cfg | 75 ---------------------------------- support/openocd/run_0.4.0.cfg | 75 ---------------------------------- 9 files changed, 329 insertions(+), 329 deletions(-) create mode 100644 support/openocd/debug_0.3.cfg create mode 100644 support/openocd/debug_0.4.cfg delete mode 100644 support/openocd/flash.cfg create mode 100644 support/openocd/flash_0.3.cfg delete mode 100644 support/openocd/flash_0.4.0.cfg create mode 100644 support/openocd/flash_0.4.cfg delete mode 100644 support/openocd/run.cfg delete mode 100644 support/openocd/run_0.4.0.cfg (limited to 'support') diff --git a/support/make/build-rules.mk b/support/make/build-rules.mk index 4dcf00f..330cdd8 100644 --- a/support/make/build-rules.mk +++ b/support/make/build-rules.mk @@ -9,7 +9,7 @@ DISAS := arm-none-eabi-objdump OBJDUMP := arm-none-eabi-objdump SIZE := arm-none-eabi-size DFU := dfu-util -OPENOCD := openocd +OPENOCD_WRAPPER := support/scripts/openocd-wrapper.sh # Suppress annoying output unless V is set ifndef V diff --git a/support/openocd/debug_0.3.cfg b/support/openocd/debug_0.3.cfg new file mode 100644 index 0000000..87d33ae --- /dev/null +++ b/support/openocd/debug_0.3.cfg @@ -0,0 +1,75 @@ +# script for stm32 + +interface ft2232 +ft2232_device_desc "Olimex OpenOCD JTAG" +ft2232_layout olimex-jtag +ft2232_vid_pid 0x15ba 0x0003 + +if { [info exists CHIPNAME] } { + set _CHIPNAME $CHIPNAME +} else { + set _CHIPNAME stm32 +} + +if { [info exists ENDIAN] } { + set _ENDIAN $ENDIAN +} else { + set _ENDIAN little +} + +# jtag speed speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so ufse F_JTAG = 1MHz +jtag_khz 1000 + +jtag_nsrst_delay 100 +jtag_ntrst_delay 100 + +#use combined on interfaces or targets that can't set TRST/SRST separately +reset_config trst_and_srst + +#jtag scan chain +if { [info exists CPUTAPID ] } { + set _CPUTAPID $CPUTAPID +} else { + # See STM Document RM0008 + # Section 30.6.3 + set _CPUTAPID 0x3ba00477 +} + +jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID + +if { [info exists BSTAPID ] } { + # FIXME this never gets used to override defaults... + set _BSTAPID $BSTAPID +} else { + # See STM Document RM0008 + # Section 29.6.2 + # Low density devices, Rev A + set _BSTAPID1 0x06412041 + # Medium density devices, Rev A + set _BSTAPID2 0x06410041 + # Medium density devices, Rev B and Rev Z + set _BSTAPID3 0x16410041 + # High density devices, Rev A + set _BSTAPID4 0x06414041 + # Connectivity line devices, Rev A and Rev Z + set _BSTAPID5 0x06418041 +} +jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \ + -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \ + -expected-id $_BSTAPID4 -expected-id $_BSTAPID5 + + +set _TARGETNAME $_CHIPNAME.cpu +target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME + +$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x5000 -work-area-backup 0 + +flash bank stm32x 0x08000000 0x00020000 0 0 $_TARGETNAME + +proc nopforever {} { + puts "Resetting the chip..." + reset run +} + +init +nopforever diff --git a/support/openocd/debug_0.4.cfg b/support/openocd/debug_0.4.cfg new file mode 100644 index 0000000..bbc8864 --- /dev/null +++ b/support/openocd/debug_0.4.cfg @@ -0,0 +1,75 @@ +# script for stm32 + +interface ft2232 +ft2232_device_desc "Olimex OpenOCD JTAG" +ft2232_layout olimex-jtag +ft2232_vid_pid 0x15ba 0x0003 + +if { [info exists CHIPNAME] } { + set _CHIPNAME $CHIPNAME +} else { + set _CHIPNAME stm32 +} + +if { [info exists ENDIAN] } { + set _ENDIAN $ENDIAN +} else { + set _ENDIAN little +} + +# jtag speed speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so ufse F_JTAG = 1MHz +jtag_khz 1000 + +jtag_nsrst_delay 100 +jtag_ntrst_delay 100 + +#use combined on interfaces or targets that can't set TRST/SRST separately +reset_config trst_and_srst + +#jtag scan chain +if { [info exists CPUTAPID ] } { + set _CPUTAPID $CPUTAPID +} else { + # See STM Document RM0008 + # Section 30.6.3 + set _CPUTAPID 0x3ba00477 +} + +jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID + +if { [info exists BSTAPID ] } { + # FIXME this never gets used to override defaults... + set _BSTAPID $BSTAPID +} else { + # See STM Document RM0008 + # Section 29.6.2 + # Low density devices, Rev A + set _BSTAPID1 0x06412041 + # Medium density devices, Rev A + set _BSTAPID2 0x06410041 + # Medium density devices, Rev B and Rev Z + set _BSTAPID3 0x16410041 + # High density devices, Rev A + set _BSTAPID4 0x06414041 + # Connectivity line devices, Rev A and Rev Z + set _BSTAPID5 0x06418041 +} +jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \ + -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \ + -expected-id $_BSTAPID4 -expected-id $_BSTAPID5 + + +set _TARGETNAME $_CHIPNAME.cpu +target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME + +$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x5000 -work-area-backup 0 + +flash bank bank0 stm32x 0x08000000 0x00020000 0 0 $_TARGETNAME + +proc nopforever {} { + puts "Resetting the chip..." + reset run +} + +init +nopforever diff --git a/support/openocd/flash.cfg b/support/openocd/flash.cfg deleted file mode 100644 index 41c6532..0000000 --- a/support/openocd/flash.cfg +++ /dev/null @@ -1,89 +0,0 @@ -# script for stm32 - -interface ft2232 -ft2232_device_desc "Olimex OpenOCD JTAG" -ft2232_layout olimex-jtag -ft2232_vid_pid 0x15ba 0x0003 - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME stm32 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -# jtag speed speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so ufse F_JTAG = 1MHz -jtag_khz 1000 - -jtag_nsrst_delay 100 -jtag_ntrst_delay 100 - -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config trst_and_srst - -#jtag scan chain -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # See STM Document RM0008 - # Section 30.6.3 - set _CPUTAPID 0x3ba00477 -} - -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -if { [info exists BSTAPID ] } { - # FIXME this never gets used to override defaults... - set _BSTAPID $BSTAPID -} else { - # See STM Document RM0008 - # Section 29.6.2 - # Low density devices, Rev A - set _BSTAPID1 0x06412041 - # Medium density devices, Rev A - set _BSTAPID2 0x06410041 - # Medium density devices, Rev B and Rev Z - set _BSTAPID3 0x16410041 - # High density devices, Rev A - set _BSTAPID4 0x06414041 - # Connectivity line devices, Rev A and Rev Z - set _BSTAPID5 0x06418041 -} -jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \ - -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \ - -expected-id $_BSTAPID4 -expected-id $_BSTAPID5 - - -set _TARGETNAME $_CHIPNAME.cpu -target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x5000 -work-area-backup 0 -# TODO: native -#$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x10000 -work-area-backup 0 - -flash bank stm32x 0x08000000 0x00020000 0 0 $_TARGETNAME - -proc flash_chip {} { - echo "Halting..." - halt - echo "Erasing..." - flash erase_address 0x08000000 0x20000 - # TODO: native - #flash erase_address 0x08000000 0x80000 - echo "Flashing image..." - flash write_bank 0 build/maple.bin 0 - echo "Verifying image..." - verify_image build/maple.bin 0x08000000 bin - echo "Checksum verified, resetting chip" - reset run - echo "Daemon shutdown" - shutdown -} - -init -flash_chip diff --git a/support/openocd/flash_0.3.cfg b/support/openocd/flash_0.3.cfg new file mode 100644 index 0000000..41c6532 --- /dev/null +++ b/support/openocd/flash_0.3.cfg @@ -0,0 +1,89 @@ +# script for stm32 + +interface ft2232 +ft2232_device_desc "Olimex OpenOCD JTAG" +ft2232_layout olimex-jtag +ft2232_vid_pid 0x15ba 0x0003 + +if { [info exists CHIPNAME] } { + set _CHIPNAME $CHIPNAME +} else { + set _CHIPNAME stm32 +} + +if { [info exists ENDIAN] } { + set _ENDIAN $ENDIAN +} else { + set _ENDIAN little +} + +# jtag speed speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so ufse F_JTAG = 1MHz +jtag_khz 1000 + +jtag_nsrst_delay 100 +jtag_ntrst_delay 100 + +#use combined on interfaces or targets that can't set TRST/SRST separately +reset_config trst_and_srst + +#jtag scan chain +if { [info exists CPUTAPID ] } { + set _CPUTAPID $CPUTAPID +} else { + # See STM Document RM0008 + # Section 30.6.3 + set _CPUTAPID 0x3ba00477 +} + +jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID + +if { [info exists BSTAPID ] } { + # FIXME this never gets used to override defaults... + set _BSTAPID $BSTAPID +} else { + # See STM Document RM0008 + # Section 29.6.2 + # Low density devices, Rev A + set _BSTAPID1 0x06412041 + # Medium density devices, Rev A + set _BSTAPID2 0x06410041 + # Medium density devices, Rev B and Rev Z + set _BSTAPID3 0x16410041 + # High density devices, Rev A + set _BSTAPID4 0x06414041 + # Connectivity line devices, Rev A and Rev Z + set _BSTAPID5 0x06418041 +} +jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \ + -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \ + -expected-id $_BSTAPID4 -expected-id $_BSTAPID5 + + +set _TARGETNAME $_CHIPNAME.cpu +target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME + +$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x5000 -work-area-backup 0 +# TODO: native +#$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x10000 -work-area-backup 0 + +flash bank stm32x 0x08000000 0x00020000 0 0 $_TARGETNAME + +proc flash_chip {} { + echo "Halting..." + halt + echo "Erasing..." + flash erase_address 0x08000000 0x20000 + # TODO: native + #flash erase_address 0x08000000 0x80000 + echo "Flashing image..." + flash write_bank 0 build/maple.bin 0 + echo "Verifying image..." + verify_image build/maple.bin 0x08000000 bin + echo "Checksum verified, resetting chip" + reset run + echo "Daemon shutdown" + shutdown +} + +init +flash_chip diff --git a/support/openocd/flash_0.4.0.cfg b/support/openocd/flash_0.4.0.cfg deleted file mode 100644 index e66d28d..0000000 --- a/support/openocd/flash_0.4.0.cfg +++ /dev/null @@ -1,89 +0,0 @@ -# script for stm32 - -interface ft2232 -ft2232_device_desc "Olimex OpenOCD JTAG" -ft2232_layout olimex-jtag -ft2232_vid_pid 0x15ba 0x0003 - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME stm32 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -# jtag speed speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so ufse F_JTAG = 1MHz -jtag_khz 1000 - -jtag_nsrst_delay 100 -jtag_ntrst_delay 100 - -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config trst_and_srst - -#jtag scan chain -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # See STM Document RM0008 - # Section 30.6.3 - set _CPUTAPID 0x3ba00477 -} - -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -if { [info exists BSTAPID ] } { - # FIXME this never gets used to override defaults... - set _BSTAPID $BSTAPID -} else { - # See STM Document RM0008 - # Section 29.6.2 - # Low density devices, Rev A - set _BSTAPID1 0x06412041 - # Medium density devices, Rev A - set _BSTAPID2 0x06410041 - # Medium density devices, Rev B and Rev Z - set _BSTAPID3 0x16410041 - # High density devices, Rev A - set _BSTAPID4 0x06414041 - # Connectivity line devices, Rev A and Rev Z - set _BSTAPID5 0x06418041 -} -jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \ - -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \ - -expected-id $_BSTAPID4 -expected-id $_BSTAPID5 - - -set _TARGETNAME $_CHIPNAME.cpu -target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x5000 -work-area-backup 0 -# TODO: native -#$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x10000 -work-area-backup 0 - -flash bank bank0 stm32x 0x08000000 0x00020000 0 0 $_TARGETNAME - -proc flash_chip {} { - echo "Halting..." - halt - echo "Erasing..." - flash erase_address 0x08000000 0x20000 - # TODO: native - #flash erase_address 0x08000000 0x80000 - echo "Flashing image..." - flash write_bank 0 build/maple.bin 0 - echo "Verifying image..." - verify_image build/maple.bin 0x08000000 bin - echo "Checksum verified, resetting chip" - reset run - echo "Daemon shutdown" - shutdown -} - -init -flash_chip diff --git a/support/openocd/flash_0.4.cfg b/support/openocd/flash_0.4.cfg new file mode 100644 index 0000000..e66d28d --- /dev/null +++ b/support/openocd/flash_0.4.cfg @@ -0,0 +1,89 @@ +# script for stm32 + +interface ft2232 +ft2232_device_desc "Olimex OpenOCD JTAG" +ft2232_layout olimex-jtag +ft2232_vid_pid 0x15ba 0x0003 + +if { [info exists CHIPNAME] } { + set _CHIPNAME $CHIPNAME +} else { + set _CHIPNAME stm32 +} + +if { [info exists ENDIAN] } { + set _ENDIAN $ENDIAN +} else { + set _ENDIAN little +} + +# jtag speed speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so ufse F_JTAG = 1MHz +jtag_khz 1000 + +jtag_nsrst_delay 100 +jtag_ntrst_delay 100 + +#use combined on interfaces or targets that can't set TRST/SRST separately +reset_config trst_and_srst + +#jtag scan chain +if { [info exists CPUTAPID ] } { + set _CPUTAPID $CPUTAPID +} else { + # See STM Document RM0008 + # Section 30.6.3 + set _CPUTAPID 0x3ba00477 +} + +jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID + +if { [info exists BSTAPID ] } { + # FIXME this never gets used to override defaults... + set _BSTAPID $BSTAPID +} else { + # See STM Document RM0008 + # Section 29.6.2 + # Low density devices, Rev A + set _BSTAPID1 0x06412041 + # Medium density devices, Rev A + set _BSTAPID2 0x06410041 + # Medium density devices, Rev B and Rev Z + set _BSTAPID3 0x16410041 + # High density devices, Rev A + set _BSTAPID4 0x06414041 + # Connectivity line devices, Rev A and Rev Z + set _BSTAPID5 0x06418041 +} +jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \ + -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \ + -expected-id $_BSTAPID4 -expected-id $_BSTAPID5 + + +set _TARGETNAME $_CHIPNAME.cpu +target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME + +$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x5000 -work-area-backup 0 +# TODO: native +#$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x10000 -work-area-backup 0 + +flash bank bank0 stm32x 0x08000000 0x00020000 0 0 $_TARGETNAME + +proc flash_chip {} { + echo "Halting..." + halt + echo "Erasing..." + flash erase_address 0x08000000 0x20000 + # TODO: native + #flash erase_address 0x08000000 0x80000 + echo "Flashing image..." + flash write_bank 0 build/maple.bin 0 + echo "Verifying image..." + verify_image build/maple.bin 0x08000000 bin + echo "Checksum verified, resetting chip" + reset run + echo "Daemon shutdown" + shutdown +} + +init +flash_chip diff --git a/support/openocd/run.cfg b/support/openocd/run.cfg deleted file mode 100644 index 87d33ae..0000000 --- a/support/openocd/run.cfg +++ /dev/null @@ -1,75 +0,0 @@ -# script for stm32 - -interface ft2232 -ft2232_device_desc "Olimex OpenOCD JTAG" -ft2232_layout olimex-jtag -ft2232_vid_pid 0x15ba 0x0003 - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME stm32 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -# jtag speed speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so ufse F_JTAG = 1MHz -jtag_khz 1000 - -jtag_nsrst_delay 100 -jtag_ntrst_delay 100 - -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config trst_and_srst - -#jtag scan chain -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # See STM Document RM0008 - # Section 30.6.3 - set _CPUTAPID 0x3ba00477 -} - -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -if { [info exists BSTAPID ] } { - # FIXME this never gets used to override defaults... - set _BSTAPID $BSTAPID -} else { - # See STM Document RM0008 - # Section 29.6.2 - # Low density devices, Rev A - set _BSTAPID1 0x06412041 - # Medium density devices, Rev A - set _BSTAPID2 0x06410041 - # Medium density devices, Rev B and Rev Z - set _BSTAPID3 0x16410041 - # High density devices, Rev A - set _BSTAPID4 0x06414041 - # Connectivity line devices, Rev A and Rev Z - set _BSTAPID5 0x06418041 -} -jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \ - -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \ - -expected-id $_BSTAPID4 -expected-id $_BSTAPID5 - - -set _TARGETNAME $_CHIPNAME.cpu -target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x5000 -work-area-backup 0 - -flash bank stm32x 0x08000000 0x00020000 0 0 $_TARGETNAME - -proc nopforever {} { - puts "Resetting the chip..." - reset run -} - -init -nopforever diff --git a/support/openocd/run_0.4.0.cfg b/support/openocd/run_0.4.0.cfg deleted file mode 100644 index bbc8864..0000000 --- a/support/openocd/run_0.4.0.cfg +++ /dev/null @@ -1,75 +0,0 @@ -# script for stm32 - -interface ft2232 -ft2232_device_desc "Olimex OpenOCD JTAG" -ft2232_layout olimex-jtag -ft2232_vid_pid 0x15ba 0x0003 - -if { [info exists CHIPNAME] } { - set _CHIPNAME $CHIPNAME -} else { - set _CHIPNAME stm32 -} - -if { [info exists ENDIAN] } { - set _ENDIAN $ENDIAN -} else { - set _ENDIAN little -} - -# jtag speed speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so ufse F_JTAG = 1MHz -jtag_khz 1000 - -jtag_nsrst_delay 100 -jtag_ntrst_delay 100 - -#use combined on interfaces or targets that can't set TRST/SRST separately -reset_config trst_and_srst - -#jtag scan chain -if { [info exists CPUTAPID ] } { - set _CPUTAPID $CPUTAPID -} else { - # See STM Document RM0008 - # Section 30.6.3 - set _CPUTAPID 0x3ba00477 -} - -jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID - -if { [info exists BSTAPID ] } { - # FIXME this never gets used to override defaults... - set _BSTAPID $BSTAPID -} else { - # See STM Document RM0008 - # Section 29.6.2 - # Low density devices, Rev A - set _BSTAPID1 0x06412041 - # Medium density devices, Rev A - set _BSTAPID2 0x06410041 - # Medium density devices, Rev B and Rev Z - set _BSTAPID3 0x16410041 - # High density devices, Rev A - set _BSTAPID4 0x06414041 - # Connectivity line devices, Rev A and Rev Z - set _BSTAPID5 0x06418041 -} -jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \ - -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \ - -expected-id $_BSTAPID4 -expected-id $_BSTAPID5 - - -set _TARGETNAME $_CHIPNAME.cpu -target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME - -$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x5000 -work-area-backup 0 - -flash bank bank0 stm32x 0x08000000 0x00020000 0 0 $_TARGETNAME - -proc nopforever {} { - puts "Resetting the chip..." - reset run -} - -init -nopforever -- cgit v1.2.3