From d9f2a93159df96eef0d8084b96df7268533177ff Mon Sep 17 00:00:00 2001
From: Perry Hung <iperry@gmail.com>
Date: Thu, 26 May 2011 20:13:09 -0400
Subject: openocd: Detect openocd version

Small script to detect the openocd version and choose the appropriate
debug/flash script for use with JTAG debugging.
---
 support/openocd/flash_0.4.0.cfg | 89 -----------------------------------------
 1 file changed, 89 deletions(-)
 delete mode 100644 support/openocd/flash_0.4.0.cfg

(limited to 'support/openocd/flash_0.4.0.cfg')

diff --git a/support/openocd/flash_0.4.0.cfg b/support/openocd/flash_0.4.0.cfg
deleted file mode 100644
index e66d28d..0000000
--- a/support/openocd/flash_0.4.0.cfg
+++ /dev/null
@@ -1,89 +0,0 @@
-# script for stm32
-
-interface ft2232
-ft2232_device_desc "Olimex OpenOCD JTAG"
-ft2232_layout olimex-jtag
-ft2232_vid_pid 0x15ba 0x0003
-
-if { [info exists CHIPNAME] } {
-   set  _CHIPNAME $CHIPNAME
-} else {
-   set  _CHIPNAME stm32
-}
-
-if { [info exists ENDIAN] } {
-   set  _ENDIAN $ENDIAN
-} else {
-   set  _ENDIAN little
-}
-
-# jtag speed speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so ufse F_JTAG = 1MHz
-jtag_khz 1000
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
-
-#jtag scan chain
-if { [info exists CPUTAPID ] } {
-   set _CPUTAPID $CPUTAPID
-} else {
-  # See STM Document RM0008
-  # Section 30.6.3
-   set _CPUTAPID 0x3ba00477
-}
-
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-if { [info exists BSTAPID ] } {
-   # FIXME this never gets used to override defaults...
-   set _BSTAPID $BSTAPID
-} else {
-  # See STM Document RM0008
-  # Section 29.6.2
-  # Low density devices, Rev A
-  set _BSTAPID1 0x06412041
-  # Medium density devices, Rev A
-  set _BSTAPID2 0x06410041
-  # Medium density devices, Rev B and Rev Z
-  set _BSTAPID3 0x16410041
-  # High density devices, Rev A
-  set _BSTAPID4 0x06414041
-  # Connectivity line devices, Rev A and Rev Z
-  set _BSTAPID5 0x06418041
-}
-jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
-           -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \
-           -expected-id $_BSTAPID4 -expected-id $_BSTAPID5
-
-
-set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME
-
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x5000 -work-area-backup 0
-# TODO: native
-#$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 0x10000 -work-area-backup 0
-
-flash bank bank0 stm32x 0x08000000 0x00020000 0 0 $_TARGETNAME
-
-proc flash_chip {} {
-    echo "Halting..."
-    halt
-    echo "Erasing..."
-    flash erase_address 0x08000000 0x20000
-    # TODO: native
-    #flash erase_address 0x08000000 0x80000
-    echo "Flashing image..."
-    flash write_bank 0 build/maple.bin 0
-    echo "Verifying image..."
-    verify_image build/maple.bin 0x08000000 bin
-    echo "Checksum verified, resetting chip"
-    reset run
-    echo "Daemon shutdown"
-    shutdown
-}
-
-init
-flash_chip
-- 
cgit v1.2.3