From d7d3dfe1a9ba483047d7a9835d526f540e00c417 Mon Sep 17 00:00:00 2001 From: bnewbold Date: Fri, 18 Jun 2010 22:00:35 -0400 Subject: info cleanup --- notes/i2c | 134 -------------------------------------------------------------- 1 file changed, 134 deletions(-) delete mode 100644 notes/i2c (limited to 'notes') diff --git a/notes/i2c b/notes/i2c deleted file mode 100644 index c324bb2..0000000 --- a/notes/i2c +++ /dev/null @@ -1,134 +0,0 @@ - -Maple ------------------------------------------------------------------------- - -We'll probably want both HardwareI2C and SoftI2C implementations, with the -soft being bitbanged on arbitrary pins (and possibly only master-mode; almost -certainly not multi-master). - -The first simple implementation will support up to 400khz operation, only -7-bit addresses, no clock stretching (on our part), only blocking master -read/write (with timeout), and only master n-write,n-read combined messages. - -A more advanced implementation would be event-driven, support DMA, higher -clock speeds, handle error interrupts, etc. - -Should all of these return a status code? or just fail? or fail silently? - -Ring buffers etc are not needed because the length of the read/write is always -known (or handled by the application code for slave mode). - -// port = {1,2} -i2c_init(port, freq) -i2c_disable(port) - -// blocking/polling -i2c_master_read(port, slave_addr, *data, len) // wrapper around writeread -i2c_master_write(port, slave_addr, *data, len) // wrapper around writeread -i2c_master_writeread(port, slave_addr, *wdata, wlen, *rdata, rlen) - -// callbacks/interrupts -i2c_slave_set_addr(port, addr) // enables callbacks etc if they aren't already; - // set ACK high -i2c_slave_set_rx_callback(port, *function) // takes a byte? -i2c_slave_set_tx_callback(port, *function) // gives a byte? - -How to init: - - setup pins - - setup peripheral input clock: 4MHz for fast mode - - configure clock control registers - - configure rise time register - - configure interrupts - - configure I2C_CR1 to enable the peripheral - - set ACK flag low: won't be a slave until addr is set - -How to master_write: - - START, addr[0:7], W, ACK, DATA[0:7], ACK, DATA[8:15], ..., STOP - - software sets START high, which toggles M/SL to master mode - - when START actually happens, SB is set and interrupt happens; hardware - waits until address is written to DR - - address shifts out and an interrupt is thrown with ADDR high; if LSB of - address was low, in transmitter mode. TRA reflects this - - software writes to the first byte to DR and clears ADDR - - first byte shifts out and when there's an ACK an interrupt is thrown - with TxE high; if no new byte was written to DR since the previous - transmission BTF goes high - - software writes next byte to DR and clears BTF, or sets STOP bit to end - data transmission, or sets START to begin next part of combined session - - after STOP is set, hardware goes back to slave mode - -How to master_read: - - START, addr[0:7], R, ACK, DATA[0:7], ACK, ..., NACK, DATA[-8:-1], STOP - - software sets START high, which toggles M/SL to master mode - - when START actually happens, SB is set and interrupt happens; hardware - waits until address is written to DR - - address shifts out and an interrupt is thrown with ADDR high; if LSB of - address was high, in receiver mode. TRA reflects this. - - software clears ADDR; hardware shifts in first byte from slave and sends ACK - if ACK is set. interrupt is thrown with RxNE high, with BTF set - - if only reading one byte, ACK should be set low and STOP high; hardware will - then NACK and STOP after reading - - software reads from DR and clears BTF bit. next byte is shifted in - - software sets NACK low after second-to-last byte is read by setting ACK low - after reading from DR, and either setting STOP or START high - - after STOP is set, hardware goes back to slave mode - -How to master_writeread: - - [START, addr[0:7], W, ACK, WDATA[0:7], ...], - [START, addr[0:7], R, ACK, RDATA[0:7], ACK, ..., NACK, RDATA[-8:-1]] - STOP - - implement the above read/write but set START high instead of STOP high at - the end - -How to slave tx (master read): - - if address is matched, ACK is send (if ACK flag is high) and ADDR goes high; - event interrupt is triggered if ITEVFEN flag is set. TRA indicates whether - this is a read or write request - - program sets DR degister and clears ADDR flag; hardware will clock stretch - until ADDR is low - - if ITVENFEN and ITBUFEN are set, the TxE interrupt is triggered after the - byte is sent and the master ACKs. now the hardware stretches until BTF is - cleared before sending again. - - after the STOP is sent, hardware sets STOPF, throws an event if ITEVFEN is - high, and waits for a read of SR1 and write CR1 - -How to slave rx (master write): - - if address is matched, ACK is send (if ACK flag is high) and ADDR goes high; - event interrupt is triggered if ITEVFEN flag is set. TRA indicates whether - this is a read or write request - - the hardware shifts in the byte to DR and sends an ACK if ACK flag is high - - if ITEVFEN and ITBUFEN are set, an RxNE interrupt is sent. hardware waits - until the BTF flag is reset - - after the STOP is sent, hardware sets STOPF, throws an event if ITEVFEN is - high, and waits for a read of SR1 and write CR1 - -i2c General Reference --------------------------------------------------------- - -http://en.wikipedia.org/wiki/I²C - -4 modes/roles for a given device. These designations are transaction specific; -a device can switch roles from one transaction to the next: - master transmit - master receive - slave transmit - slave receive - - -STM32 Specific Reference ------------------------------------------------------ - -see stm32 docs: reference manual (doc 13902 rev10) pg637/1003 - -see STM32F10x_StdPeriph_Lib_V3.2.0/Project/STM32F10x_StdPeriph_Examples/I2C/Interrupt for an example project (reading/writing between the two i2c buses) based on the stm32library - ->100khz is "fast mode", which goes up to 400khz. stm32 supports up to 400khz. - things are different in fast mode: 4mhz input clock - -interrupts see pg652/1003 -registers see pg654/1003 - -PEC = packet error checking. don't think this is i2c standard - -each i2c port has an error and an event interrupt - -the stm32 is in slave mode by default; it enters master only when executing -a request - -- cgit v1.2.3