From 3cc4517f4be4044b761d16f8293b0a8b979e8c89 Mon Sep 17 00:00:00 2001 From: Marti Bolivar Date: Thu, 7 Jun 2012 05:20:35 -0400 Subject: libmaple/timer.h: Doxygen beautification and fixups Make the Doxygen comments nicer to look at. Some of the docstrings are out-of-date since F2 support was added, so update them. Signed-off-by: Marti Bolivar --- libmaple/include/libmaple/timer.h | 207 ++++++++++++++++++++------------------ 1 file changed, 109 insertions(+), 98 deletions(-) (limited to 'libmaple') diff --git a/libmaple/include/libmaple/timer.h b/libmaple/include/libmaple/timer.h index 3563749..f411f17 100644 --- a/libmaple/include/libmaple/timer.h +++ b/libmaple/include/libmaple/timer.h @@ -596,27 +596,32 @@ extern timer_dev *TIMER14; */ /** - * Used to configure the behavior of a timer channel. Note that not - * all timers can be configured in every mode. + * @brief Used to configure the behavior of a timer channel. + * + * Be careful: not all timers can be configured in every mode. */ -/* TODO TIMER_PWM_CENTER_ALIGNED, TIMER_INPUT_CAPTURE, TIMER_ONE_PULSE */ typedef enum timer_mode { - TIMER_DISABLED, /**< In this mode, the timer stops counting, - channel interrupts are detached, and no state - changes are output. */ - TIMER_PWM, /**< PWM output mode. This is the default mode for pins - after initialization. */ - /* TIMER_PWM_CENTER_ALIGNED, /\**< Center-aligned PWM output mode. *\/ */ - TIMER_OUTPUT_COMPARE, /**< In this mode, the timer counts from 0 - to its reload value repeatedly; every - time the counter value reaches one of - the channel compare values, the - corresponding interrupt is fired. */ - /* TIMER_INPUT_CAPTURE, /\**< In this mode, the timer can measure the */ - /* pulse lengths of input signals. *\/ */ - /* TIMER_ONE_PULSE /\**< In this mode, the timer can generate a single */ - /* pulse on a GPIO pin for a specified amount of */ - /* time. *\/ */ + /** + * The timer stops counting, channel interrupts are detached, and + * no state changes are output. */ + TIMER_DISABLED, + + /** PWM output. */ + TIMER_PWM, + + /* TIMER_PWM_CENTER_ALIGNED, TODO: Center-aligned PWM output mode. */ + + /** + * The timer counts from 0 to its reload value repeatedly; every + * time the counter value reaches one of the channel compare + * values, the corresponding interrupt is fired. */ + TIMER_OUTPUT_COMPARE, + + /* TIMER_INPUT_CAPTURE, TODO: In this mode, the timer can measure the + * pulse lengths of input signals */ + /* TIMER_ONE_PULSE, TODO: In this mode, the timer can generate a single + * pulse on a GPIO pin for a specified amount of + * time. */ } timer_mode; /** Timer channel numbers */ @@ -646,23 +651,21 @@ int timer_has_cc_channel(timer_dev *dev, uint8 channel); /** * @brief Timer interrupt number. * - * Not all timers support all of these values. General purpose timers - * can be a special nuisance in this regard. + * Not all timers support all of these values. All timers support + * TIMER_UPDATE_INTERRUPT. "General purpose" timers can be a special + * nuisance in this regard, as they individually support different + * subsets of the available interupts. Consult your target's reference + * manual for the details. */ typedef enum timer_interrupt_id { - TIMER_UPDATE_INTERRUPT, /**< Update interrupt, available on all timers. */ - TIMER_CC1_INTERRUPT, /**< Capture/compare 1 interrupt, available - on general and advanced timers only. */ - TIMER_CC2_INTERRUPT, /**< Capture/compare 2 interrupt, general and - advanced timers only. */ - TIMER_CC3_INTERRUPT, /**< Capture/compare 3 interrupt, general and - advanced timers only. */ - TIMER_CC4_INTERRUPT, /**< Capture/compare 4 interrupt, general and - advanced timers only. */ - TIMER_COM_INTERRUPT, /**< COM interrupt, advanced timers only */ - TIMER_TRG_INTERRUPT, /**< Trigger interrupt, general and advanced - timers only */ - TIMER_BREAK_INTERRUPT /**< Break interrupt, advanced timers only. */ + TIMER_UPDATE_INTERRUPT, /**< Update interrupt. */ + TIMER_CC1_INTERRUPT, /**< Capture/compare 1 interrupt. */ + TIMER_CC2_INTERRUPT, /**< Capture/compare 2 interrupt. */ + TIMER_CC3_INTERRUPT, /**< Capture/compare 3 interrupt. */ + TIMER_CC4_INTERRUPT, /**< Capture/compare 4 interrupt. */ + TIMER_COM_INTERRUPT, /**< COM interrupt. */ + TIMER_TRG_INTERRUPT, /**< Trigger interrupt. */ + TIMER_BREAK_INTERRUPT, /**< Break interrupt. */ } timer_interrupt_id; void timer_attach_interrupt(timer_dev *dev, @@ -957,41 +960,46 @@ static inline void timer_dma_set_burst_len(timer_dev *dev, uint8 length) { * Defines the base address for DMA transfers. */ typedef enum timer_dma_base_addr { - TIMER_DMA_BASE_CR1 = TIMER_DCR_DBA_CR1, /**< Base is control register 1 */ - TIMER_DMA_BASE_CR2 = TIMER_DCR_DBA_CR2, /**< Base is control register 2 */ - TIMER_DMA_BASE_SMCR = TIMER_DCR_DBA_SMCR, /**< Base is slave mode - control register */ - TIMER_DMA_BASE_DIER = TIMER_DCR_DBA_DIER, /**< Base is DMA interrupt enable - register */ - TIMER_DMA_BASE_SR = TIMER_DCR_DBA_SR, /**< Base is status register */ - TIMER_DMA_BASE_EGR = TIMER_DCR_DBA_EGR, /**< Base is event generation - register */ - TIMER_DMA_BASE_CCMR1 = TIMER_DCR_DBA_CCMR1, /**< Base is capture/compare - mode register 1 */ - TIMER_DMA_BASE_CCMR2 = TIMER_DCR_DBA_CCMR2, /**< Base is capture/compare - mode register 2 */ - TIMER_DMA_BASE_CCER = TIMER_DCR_DBA_CCER, /**< Base is capture/compare - enable register */ - TIMER_DMA_BASE_CNT = TIMER_DCR_DBA_CNT, /**< Base is counter */ - TIMER_DMA_BASE_PSC = TIMER_DCR_DBA_PSC, /**< Base is prescaler */ - TIMER_DMA_BASE_ARR = TIMER_DCR_DBA_ARR, /**< Base is auto-reload - register */ - TIMER_DMA_BASE_RCR = TIMER_DCR_DBA_RCR, /**< Base is repetition - counter register */ - TIMER_DMA_BASE_CCR1 = TIMER_DCR_DBA_CCR1, /**< Base is capture/compare - register 1 */ - TIMER_DMA_BASE_CCR2 = TIMER_DCR_DBA_CCR2, /**< Base is capture/compare - register 2 */ - TIMER_DMA_BASE_CCR3 = TIMER_DCR_DBA_CCR3, /**< Base is capture/compare - register 3 */ - TIMER_DMA_BASE_CCR4 = TIMER_DCR_DBA_CCR4, /**< Base is capture/compare - register 4 */ - TIMER_DMA_BASE_BDTR = TIMER_DCR_DBA_BDTR, /**< Base is break and - dead-time register */ - TIMER_DMA_BASE_DCR = TIMER_DCR_DBA_DCR, /**< Base is DMA control - register */ - TIMER_DMA_BASE_DMAR = TIMER_DCR_DBA_DMAR /**< Base is DMA address for - full transfer */ + /** Base is control register 1 */ + TIMER_DMA_BASE_CR1 = TIMER_DCR_DBA_CR1, + /** Base is control register 2 */ + TIMER_DMA_BASE_CR2 = TIMER_DCR_DBA_CR2, + /** Base is slave mode control register */ + TIMER_DMA_BASE_SMCR = TIMER_DCR_DBA_SMCR, + /** Base is DMA interrupt enable register */ + TIMER_DMA_BASE_DIER = TIMER_DCR_DBA_DIER, + /** Base is status register */ + TIMER_DMA_BASE_SR = TIMER_DCR_DBA_SR, + /** Base is event generation register */ + TIMER_DMA_BASE_EGR = TIMER_DCR_DBA_EGR, + /** Base is capture/compare mode register 1 */ + TIMER_DMA_BASE_CCMR1 = TIMER_DCR_DBA_CCMR1, + /** Base is capture/compare mode register 2 */ + TIMER_DMA_BASE_CCMR2 = TIMER_DCR_DBA_CCMR2, + /** Base is capture/compare enable register */ + TIMER_DMA_BASE_CCER = TIMER_DCR_DBA_CCER, + /** Base is counter */ + TIMER_DMA_BASE_CNT = TIMER_DCR_DBA_CNT, + /** Base is prescaler */ + TIMER_DMA_BASE_PSC = TIMER_DCR_DBA_PSC, + /** Base is auto-reload register */ + TIMER_DMA_BASE_ARR = TIMER_DCR_DBA_ARR, + /** Base is repetition counter register */ + TIMER_DMA_BASE_RCR = TIMER_DCR_DBA_RCR, + /** Base is capture/compare register 1 */ + TIMER_DMA_BASE_CCR1 = TIMER_DCR_DBA_CCR1, + /** Base is capture/compare register 2 */ + TIMER_DMA_BASE_CCR2 = TIMER_DCR_DBA_CCR2, + /** Base is capture/compare register 3 */ + TIMER_DMA_BASE_CCR3 = TIMER_DCR_DBA_CCR3, + /** Base is capture/compare register 4 */ + TIMER_DMA_BASE_CCR4 = TIMER_DCR_DBA_CCR4, + /** Base is break and dead-time register */ + TIMER_DMA_BASE_BDTR = TIMER_DCR_DBA_BDTR, + /** Base is DMA control register */ + TIMER_DMA_BASE_DCR = TIMER_DCR_DBA_DCR, + /** Base is DMA address for full transfer */ + TIMER_DMA_BASE_DMAR = TIMER_DCR_DBA_DMAR, } timer_dma_base_addr; /** @@ -1027,35 +1035,38 @@ static inline void timer_dma_set_base_addr(timer_dev *dev, * Timer output compare modes. */ typedef enum timer_oc_mode { - TIMER_OC_MODE_FROZEN = 0 << 4, /**< Frozen: comparison between output - compare register and counter has no - effect on the outputs. */ - TIMER_OC_MODE_ACTIVE_ON_MATCH = 1 << 4, /**< OCxREF signal is forced - high when the count matches - the channel capture/compare - register. */ - TIMER_OC_MODE_INACTIVE_ON_MATCH = 2 << 4, /**< OCxREF signal is forced - low when the counter matches - the channel capture/compare - register. */ - TIMER_OC_MODE_TOGGLE = 3 << 4, /**< OCxREF toggles when counter - matches the cannel capture/compare - register. */ - TIMER_OC_MODE_FORCE_INACTIVE = 4 << 4, /**< OCxREF is forced low. */ - TIMER_OC_MODE_FORCE_ACTIVE = 5 << 4, /**< OCxREF is forced high. */ - TIMER_OC_MODE_PWM_1 = 6 << 4, /**< PWM mode 1. In upcounting, channel is - active as long as count is less than - channel capture/compare register, else - inactive. In downcounting, channel is - inactive as long as count exceeds - capture/compare register, else - active. */ - TIMER_OC_MODE_PWM_2 = 7 << 4 /**< PWM mode 2. In upcounting, channel is - inactive as long as count is less than - capture/compare register, else active. - In downcounting, channel is active as - long as count exceeds capture/compare - register, else inactive. */ + /** + * Frozen: comparison between output compare register and counter + * has no effect on the outputs. */ + TIMER_OC_MODE_FROZEN = 0 << 4, + /** + * OCxREF signal is forced high when the count matches the channel + * capture/compare register. */ + TIMER_OC_MODE_ACTIVE_ON_MATCH = 1 << 4, + /** + * OCxREF signal is forced low when the counter matches the + * channel capture/compare register. */ + TIMER_OC_MODE_INACTIVE_ON_MATCH = 2 << 4, + /** + * OCxREF toggles when counter matches the channel capture/compare + * register. */ + TIMER_OC_MODE_TOGGLE = 3 << 4, + /** OCxREF is forced low. */ + TIMER_OC_MODE_FORCE_INACTIVE = 4 << 4, + /** OCxREF is forced high. */ + TIMER_OC_MODE_FORCE_ACTIVE = 5 << 4, + /** + * PWM mode 1. In upcounting, channel is active as long as count + * is less than channel capture/compare register, else inactive. + * In downcounting, channel is inactive as long as count exceeds + * capture/compare register, else active. */ + TIMER_OC_MODE_PWM_1 = 6 << 4, + /** + * PWM mode 2. In upcounting, channel is inactive as long as count + * is less than capture/compare register, else active. In + * downcounting, channel is active as long as count exceeds + * capture/compare register, else inactive. */ + TIMER_OC_MODE_PWM_2 = 7 << 4, } timer_oc_mode; /** -- cgit v1.2.3