From c000038c8b16a9be40ac95231c309aad05a57158 Mon Sep 17 00:00:00 2001
From: Marti Bolivar <mbolivar@leaflabs.com>
Date: Wed, 13 Jun 2012 11:57:56 -0400
Subject: examples/test-usart-dma.cpp: Use HardwareSerial::c_dev().

Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
---
 examples/test-usart-dma.cpp | 37 +++++++++++++++++++------------------
 1 file changed, 19 insertions(+), 18 deletions(-)

(limited to 'examples')

diff --git a/examples/test-usart-dma.cpp b/examples/test-usart-dma.cpp
index 7dafc3a..b3c766e 100644
--- a/examples/test-usart-dma.cpp
+++ b/examples/test-usart-dma.cpp
@@ -29,9 +29,9 @@
  * Configuration and state
  */
 
-// USART and DMA configuration
-#define USART USART2
-#define USART_HWSER Serial2
+// USART and DMA configuration. You can change these to suit your
+// purposes.
+HardwareSerial *serial = &Serial2;
 #define USART_DMA_DEV DMA1
 #define USART_RX_DMA_CHANNEL DMA_CH6
 #define BAUD 9600
@@ -60,16 +60,17 @@ void rx_dma_irq(void) {
 // 1. Turn it on.
 // 2. Set the "DMA request on RX" bit in USART_CR3 (USART_CR3_DMAR).
 void init_usart(void) {
-    USART_HWSER.begin(BAUD);
-    USART->regs->CR3 = USART_CR3_DMAR;
+    serial->begin(BAUD);
+    usart_dev *serial_dev = serial->c_dev();
+    serial_dev->regs->CR3 = USART_CR3_DMAR;
 }
 
 // Configure the DMA controller to serve DMA requests from the USART.
 void init_dma_xfer(void) {
     dma_init(USART_DMA_DEV);
     dma_setup_transfer(USART_DMA_DEV, USART_RX_DMA_CHANNEL,
-                       &USART->regs->DR, DMA_SIZE_8BITS,
-                       rx_buf,           DMA_SIZE_8BITS,
+                       &serial->c_dev()->regs->DR, DMA_SIZE_8BITS,
+                       rx_buf,                     DMA_SIZE_8BITS,
                        (DMA_MINC_MODE | DMA_CIRC_MODE | DMA_TRNS_CMPLT));
     dma_set_num_transfers(USART_DMA_DEV, USART_RX_DMA_CHANNEL,
                           BUF_SIZE - 1);
@@ -95,15 +96,15 @@ void loop(void) {
     // See if the interrupt handler got called since the last time we
     // checked.
     if (irq_fired) {
-        USART_HWSER.println("** IRQ **");
+        serial->println("** IRQ **");
         // Notice how the ISR bits show transfer complete _and_
         // half-complete here, but the ISR bits we print next will be
         // zero. That's because the variable "isr" gets set _inside_
         // rx_dma_irq(). After it exits, libmaple cleans up by
         // clearing the ISR bits. (If it didn't, and we forgot to, the
         // interrupt would repeatedly fire forever.)
-        USART_HWSER.print("ISR bits: 0x");
-        USART_HWSER.println(isr, HEX);
+        serial->print("ISR bits: 0x");
+        serial->println(isr, HEX);
         irq_fired = 0;
     }
 
@@ -116,20 +117,20 @@ void loop(void) {
     // right times no matter what; we just don't get interrupted
     // unless we asked. (If an error or other problem occurs, the
     // relevant ISR bits will get set in the same way).
-    USART_HWSER.print("[");
-    USART_HWSER.print(millis());
-    USART_HWSER.print("]\tISR bits: 0x");
+    serial->print("[");
+    serial->print(millis());
+    serial->print("]\tISR bits: 0x");
     uint8 isr_bits = dma_get_isr_bits(USART_DMA_DEV, USART_RX_DMA_CHANNEL);
-    USART_HWSER.print(isr_bits, HEX);
+    serial->print(isr_bits, HEX);
 
     // Print the contents of rx_buf. If you keep typing after it fills
     // up, the new characters will overwrite the old ones, thanks to
     // DMA_CIRC_MODE.
-    USART_HWSER.print("\tCharacter buffer contents: '");
-    USART_HWSER.print(rx_buf);
-    USART_HWSER.println("'");
+    serial->print("\tCharacter buffer contents: '");
+    serial->print(rx_buf);
+    serial->println("'");
     if (isr_bits == 0x7) {
-        USART_HWSER.println("** Clearing ISR bits.");
+        serial->println("** Clearing ISR bits.");
         dma_clear_isr_bits(USART_DMA_DEV, USART_RX_DMA_CHANNEL);
     }
 }
-- 
cgit v1.2.3