From 9fedecbc9a2621686cedb6c1259d50d5ed1bddc1 Mon Sep 17 00:00:00 2001
From: Marti Bolivar <mbolivar@leaflabs.com>
Date: Mon, 26 Sep 2011 14:39:30 -0400
Subject: test-fsmc.cpp: Switch to SerialUSB

This messes with timing a little, but makes it faster to test.  The
timing was never perfect anyway, due to incrementing count.

Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
---
 examples/test-fsmc.cpp | 61 +++++++++++++++++++++++---------------------------
 1 file changed, 28 insertions(+), 33 deletions(-)

(limited to 'examples')

diff --git a/examples/test-fsmc.cpp b/examples/test-fsmc.cpp
index 9102be6..7cb1764 100644
--- a/examples/test-fsmc.cpp
+++ b/examples/test-fsmc.cpp
@@ -19,14 +19,13 @@ void setup() {
     pinMode(BOARD_LED_PIN, OUTPUT);
     digitalWrite(BOARD_LED_PIN, HIGH);
 
-    Serial1.begin(115200);
-    Serial1.println("*** Beginning RAM chip test");
+    SerialUSB.println("*** Beginning RAM chip test");
 
     test_single_write();
     test_all_addresses();
 
-    Serial1.println("Tests pass, finished.");
-    Serial1.println("***\n");
+    SerialUSB.println("Tests pass, finished.");
+    SerialUSB.println("***\n");
 }
 
 void loop() {
@@ -36,17 +35,17 @@ void test_single_write() {
     uint16 *ptr = sram_start;
     uint16 tmp;
 
-    Serial1.print("Writing 0x1234... ");
+    SerialUSB.print("Writing 0x1234... ");
     *ptr = 0x1234;
-    Serial1.println("Done.");
+    SerialUSB.println("Done.");
 
-    Serial1.print("Reading... ");
+    SerialUSB.print("Reading... ");
     tmp = *ptr;
-    Serial1.print("Done: 0x");
-    Serial1.println(tmp, HEX);
+    SerialUSB.print("Done: 0x");
+    SerialUSB.println(tmp, HEX);
 
     if (tmp != 0x1234) {
-        Serial1.println("Mismatch; abort.");
+        SerialUSB.println("Mismatch; abort.");
         ASSERT(0);
     }
 }
@@ -56,10 +55,7 @@ void test_all_addresses() {
     uint16 count = 0;
     uint16 *ptr;
 
-    Serial1.println("Now writing all memory addresses (unrolled loop)");
-    // Turn off the USB interrupt, as it interferes most with timing
-    // (don't turn off SysTick, or we won't get micros()).
-    SerialUSB.end();
+    SerialUSB.println("Now writing all memory addresses (unrolled loop)");
     start = micros();
     for (ptr = sram_start; ptr < sram_end;) {
         *ptr++ = count++;
@@ -80,35 +76,34 @@ void test_all_addresses() {
         *ptr++ = count++;
     }
     end = micros();
-    SerialUSB.begin();
-    Serial1.print("Done. Elapsed time (us): ");
-    Serial1.println(end - start);
+    SerialUSB.print("Done. Elapsed time (us): ");
+    SerialUSB.println(end - start);
 
-    Serial1.println("Validating writes.");
+    SerialUSB.println("Validating writes.");
     for (ptr = sram_start, count = 0; ptr < sram_end; ptr++, count++) {
         uint16 value = *ptr;
         if (value != count) {
-            Serial1.print("mismatch: 0x");
-            Serial1.print((uint32)ptr);
-            Serial1.print(" = 0x");
-            Serial1.print(value, HEX);
-            Serial1.print(", should be 0x");
-            Serial1.print(count, HEX);
-            Serial1.println(".");
+            SerialUSB.print("mismatch: 0x");
+            SerialUSB.print((uint32)ptr);
+            SerialUSB.print(" = 0x");
+            SerialUSB.print(value, HEX);
+            SerialUSB.print(", should be 0x");
+            SerialUSB.print(count, HEX);
+            SerialUSB.println(".");
             ASSERT(0);
         }
     }
-    Serial1.println("Done; all writes seem valid.");
+    SerialUSB.println("Done; all writes seem valid.");
 
     ptrdiff_t nwrites = sram_end - sram_start;
     double us_per_write = double(end-start) / double(nwrites);
-    Serial1.print("Number of writes = ");
-    Serial1.print(nwrites);
-    Serial1.print("; avg. time per write = ");
-    Serial1.print(us_per_write);
-    Serial1.print(" us (");
-    Serial1.print(1 / us_per_write);
-    Serial1.println(" MHz)");
+    SerialUSB.print("Number of writes = ");
+    SerialUSB.print(nwrites);
+    SerialUSB.print("; avg. time per write = ");
+    SerialUSB.print(us_per_write);
+    SerialUSB.print(" us (");
+    SerialUSB.print(1 / us_per_write);
+    SerialUSB.println(" MHz)");
 }
 
 __attribute__((constructor)) void premain() {
-- 
cgit v1.2.3