From d7212508f203d03b4931b94695fb10cb8a7862c2 Mon Sep 17 00:00:00 2001 From: bnewbold Date: Wed, 27 Aug 2014 19:02:33 -0400 Subject: docs: first pass removal of board-specific hardware info --- docs/source/_templates/indexcontent.html | 12 - docs/source/adc.rst | 8 +- docs/source/contents.rst | 15 - docs/source/epilog.rst | 4 + docs/source/external-interrupts.rst | 8 +- docs/source/fsmc.rst | 4 +- docs/source/gpio.rst | 10 +- docs/source/hardware/maple-mini.rst | 402 ------------------- docs/source/hardware/maple-native-beta.rst | 605 ---------------------------- docs/source/hardware/maple-native.rst | 6 - docs/source/hardware/maple-ret6.rst | 466 ---------------------- docs/source/hardware/maple.rst | 618 ----------------------------- docs/source/lang/api/analogread.rst | 5 +- docs/source/lang/api/board-values.rst | 8 +- docs/source/lang/api/disabledebugports.rst | 4 +- docs/source/lang/api/pwmwrite.rst | 5 +- docs/source/language.rst | 4 +- docs/source/libs/servo.rst | 2 +- docs/source/timers.rst | 8 +- docs/source/troubleshooting.rst | 62 --- docs/source/usart.rst | 8 +- 21 files changed, 41 insertions(+), 2223 deletions(-) delete mode 100644 docs/source/hardware/maple-mini.rst delete mode 100644 docs/source/hardware/maple-native-beta.rst delete mode 100644 docs/source/hardware/maple-native.rst delete mode 100644 docs/source/hardware/maple-ret6.rst delete mode 100644 docs/source/hardware/maple.rst (limited to 'docs') diff --git a/docs/source/_templates/indexcontent.html b/docs/source/_templates/indexcontent.html index 6724303..b4410c3 100644 --- a/docs/source/_templates/indexcontent.html +++ b/docs/source/_templates/indexcontent.html @@ -41,18 +41,6 @@ changes that are new in {{ release }}.

Toolchain -

Boards

- -

Programming

diff --git a/docs/source/adc.rst b/docs/source/adc.rst index 70417ea..c308215 100644 --- a/docs/source/adc.rst +++ b/docs/source/adc.rst @@ -55,10 +55,10 @@ additional functionality, cost, and package size. More information on these isolated pins is available in each board's hardware documentation: -* :ref:`Maple ` -* :ref:`Maple RET6 Edition ` -* :ref:`Maple Mini ` -* :ref:`Maple Native Beta ` +* `Leaflabs Maple`_ +* `Leaflabs Maple RET6`_ +* `Leaflabs Maple Mini`_ +* `Leaflabs Maple Native Beta`_ That said, there are a number of more general things you can do to try to get good readings. If your input voltage changes relatively diff --git a/docs/source/contents.rst b/docs/source/contents.rst index 0738d28..ee32306 100644 --- a/docs/source/contents.rst +++ b/docs/source/contents.rst @@ -53,18 +53,3 @@ Contents in Full systick usb usart - -.. _index-boards: - -**Boards** - -.. toctree:: - :maxdepth: 2 - - hardware/maple.rst - hardware/maple-ret6.rst - hardware/maple-mini.rst - hardware/maple-native-beta.rst - -.. TODO [Maple Native] write/include upon finished Native release -.. hardware/maple-native.rst diff --git a/docs/source/epilog.rst b/docs/source/epilog.rst index b548001..0c1a091 100644 --- a/docs/source/epilog.rst +++ b/docs/source/epilog.rst @@ -12,3 +12,7 @@ .. _Git: http://git-scm.com/ .. _dfu-util: http://wiki.openmoko.org/wiki/Dfu-util .. _easy_install: http://packages.python.org/distribute/easy_install.html +.. _Leaflabs Maple: http://leaflabs.com/docs/hardware/maple-mini.html +.. _Leaflabs Maple RET6: http://leaflabs.com/docs/hardware/maple-ret6.html +.. _Leaflabs Maple Mini: http://leaflabs.com/docs/hardware/maple-mini.html +.. _Leaflabs Maple Native Beta: http://leaflabs.com/docs/hardware/maple-native-beta.html diff --git a/docs/source/external-interrupts.rst b/docs/source/external-interrupts.rst index 209d5af..817b7a8 100644 --- a/docs/source/external-interrupts.rst +++ b/docs/source/external-interrupts.rst @@ -37,10 +37,10 @@ interrupts at a time [#fextisports]_. The EXTI Line Pin Map for your board lists which pins connect to which EXTI lines: -* :ref:`Maple ` -* :ref:`Maple RET6 Edition ` -* :ref:`Maple Mini ` -* :ref:`Maple Native Beta ` +* `Leaflabs Maple`_ +* `Leaflabs Maple RET6`_ +* `Leaflabs Maple Mini`_ +* `Leaflabs Maple Native Beta`_ Function Reference ------------------ diff --git a/docs/source/fsmc.rst b/docs/source/fsmc.rst index c8f0125..ff352c4 100644 --- a/docs/source/fsmc.rst +++ b/docs/source/fsmc.rst @@ -30,4 +30,6 @@ Recommended Reading ------------------- - Wikipedia article on `SRAM `_ -- :ref:`ST RM0008 ` chapter on FSMC. +- ST RM0008 chapter on FSMC. + +.. TODO direct link to ST RM0008 diff --git a/docs/source/gpio.rst b/docs/source/gpio.rst index 929173e..c844880 100644 --- a/docs/source/gpio.rst +++ b/docs/source/gpio.rst @@ -69,12 +69,10 @@ GPIO port and bit for each pin number. The GPIO documentation for your board includes its pin map, which also lists the other peripherals by pin number: -* :ref:`Maple ` -* :ref:`Maple RET6 Edition ` -* :ref:`Maple Mini ` -* :ref:`Maple Native (Beta) ` - -.. * :ref:`Maple Native ` +* `Leaflabs Maple`_ +* `Leaflabs Maple RET6`_ +* `Leaflabs Maple Mini`_ +* `Leaflabs Maple Native Beta`_ .. _gpio-5v-tolerant: diff --git a/docs/source/hardware/maple-mini.rst b/docs/source/hardware/maple-mini.rst deleted file mode 100644 index c28211d..0000000 --- a/docs/source/hardware/maple-mini.rst +++ /dev/null @@ -1,402 +0,0 @@ -.. _maple-mini: - -Maple Mini -========== - -This page is a general resource for information specific to the Maple -Mini. The Maple Mini is a smaller version of the Maple that fits on a -breadboard. - -.. contents:: Contents - :local: - -.. TODO [dma.rst] Ref to dma.rst in sequel instead of libmaple-dma - -Technical Specifications ------------------------- - -* MCU: :ref:`STM32F103CBT6 `, a 32-bit ARM Cortex - M3 microprocessor -* Clock Speed: **72 MHz** -* **128 KB Flash** and **20 KB SRAM** -* 34 :ref:`digital I/ pins (GPIOs) ` -* 12 :ref:`PWM ` pins at 16 bit resolution -* 9 :ref:`analog input (ADC) ` pins at 12 bit resolution -* 2 :ref:`SPI ` peripherals -* 2 :ref:`I2C ` peripherals -* 7 Channels of Direct Memory Access (**DMA**) (:ref:`libmaple-dma`) -* 3 :ref:`USART (serial port) ` peripherals -* 1 advanced and 3 general-purpose :ref:`timers ` -* Dedicated :ref:`USB ` port for programming and communications -* :ref:`jtag` -* Nested Vectored Interrupt Controller (NVIC) (including - :ref:`external interrupt ` on GPIOs) -* Supplies up to 500 mA at 3.3 V, with :ref:`separate 250 mA digital - and analog regulators ` for low-noise analog - performance -* :ref:`Open source, four layer design ` -* Support for low power, sleep, and standby modes (<500 μA) -* Operating Voltage: 3.3 V -* Input Voltage (recommended): 3 V — 12 V -* Dimensions: 2.02″ × 0.72″ - -.. _maple-mini-powering: - -Powering the Maple Mini ------------------------ - -You can power the Maple Mini via the USB plug or by powering Vin -directly. - -.. warning:: The silkscreen on the Maple Mini suggests it will accept - an input voltage up to 16 V. We recommend applying **no greater - than 12 V**, and potentially even lower depending upon the current - draw requirements of the application. Please see :ref:`Power - Regulation on the Maple Mini ` for - more information. - -.. _maple-mini-power-regulation: - -Power Regulation on the Maple Mini ----------------------------------- - -Power regulation on the Maple is provided by two low dropout linear -voltage regulators. (The part is the MCP1703 from Microchip, in the -SOT-23A package. You can download the datasheet `here -`_ ). One -of the regulators supplies power to the digital voltage plane; the -other supplies power to the analog voltage plane. - -These voltage regulators nominally take an input of up to 16V. In -addition, while the maximum continuous output current for the board is -250mA, if you are powering the board off higher voltages the amount -current it can supply goes down, due to the regulators needing to -dissipate the extra power. So if you are powering the board off 12V, -the max current is about 40mA at room temperature. In general (again, -at room temperature) the max power dissipation (PD) for the chip is -about .37W, and output current = PD/(Vin-Vout). For exact max current -calculations, please refer to the datasheet linked above. - -If you are planning to draw a lot of current from the Maple board, it -is necessary to provide input power as close to 3.3V as -possible. Powering the microcontroller circuitry and LEDs on the board -alone takes approximately 30mA, so if you are powering the board with -12V that leaves only 10mA (at best) available for powering any user -circuitry. Attempting to draw more than 10mA runs the risk of shorting -out the power regulators and bricking your board. - -.. _maple-mini-gpios: - -GPIO Information ----------------- - -The Maple Mini features 34 total input/output pins, numbered ``D0`` -through ``D33``. These numbers correspond to the numeric values next -to each header on the Maple Mini's silkscreen. However, some of them -have special uses by default [#fusedpins]_. - -.. _maple-mini-usb-pins: - -Pin ``D23`` is the :ref:`USB ` D+ line, and ``D24`` is the USB D- -line. To use them as GPIOs, your program will need to :ref:`disable -SerialUSB ` first. Be aware, however, that -disabling SerialUSB means that the :ref:`bootloader ` -won't work properly, and you'll need to use -:ref:`troubleshooting-perpetual-bootloader` to make your next upload. - -.. _maple-mini-but: - -Pin ``D32`` is the Mini's :ref:`button pin `. -It is thus mainly useful as an :ref:`input `. The -pin will :ref:`read ` ``HIGH`` when the :ref:`button -is pressed `. - -.. _maple-mini-led: - -Pin ``D33`` is the Mini's :ref:`LED pin `. It -is thus mainly useful as an :ref:`output `. The LED -will glow when ``HIGH`` is :ref:`written ` to it. -(It also supports :ref:`pwm`, for finer-grained brightness control). - -.. TODO [0.1.0] silkscreen pictures which expand abbreviations - -.. _maple-mini-pin-map-master: - -Master Pin Map -^^^^^^^^^^^^^^ - -This table shows a summary the available functionality on every GPIO -pin, by peripheral type. The "5 V?" column documents whether or not -the pin is :ref:`5 volt tolerant `. - -Note that this table is not exhaustive; on some pins, more peripherals -are available than are listed here. - -.. csv-table:: - :header: Pin, :ref:`GPIO `, :ref:`ADC `, :ref:`Timer `, :ref:`I2C `, :ref:`UART `, :ref:`SPI `, 5 V? - - D0, PB11, -, -, 2_SDA, 3_RX, -, Yes - D1, PB10, -, -, 2_SCL, 3_TX, -, Yes - D2, PB2, -, -, -, -, -, Yes - D3, PB0, CH8, 3_CH3, -, -, -, - - D4, PA7, CH7, 3_CH2, -, -, 1_MOSI, - - D5, PA6, CH6, 3_CH1, -, -, 1_MISO, - - D6, PA5, CH5, -, -, -, 1_SCK, - - D7, PA4, CH4, -, -, 2_CK, 1_NSS, - - D8, PA3, CH3, 2_CH4, -, 2_RX, -, - - D9, PA2, CH2, 2_CH3, -, 2_TX, -, - - D10, PA1, CH1, 2_CH2, -, 2_RTS, -, - - D11, PA0, CH0, 2_CH1_ETR, -, 2_CTS, -, - - D12, PC15, -, -, -, -, -, - - D13, PC14, -, -, -, -, -, - - D14, PC13, -, -, -, -, -, - - D15, PB7, -, 4_CH2, 1_SDA, -, -, Yes - D16, PB6, -, 4_CH1, 2_SCL, -, -, Yes - D17, PB5, -, -, 1_SMBA, -, -, - - D18, PB4, -, -, -, -, -, Yes - D19, PB3, -, -, -, -, -, Yes - D20, PA15, -, -, -, -, -, Yes - D21, PA14, -, -, -, -, -, Yes - D22, PA13, -, -, -, -, -, Yes - D23, PA12, -, 1_ETR, -, 1_RTS, -, Yes - D24, PA11, -, 1_CH4, -, 1_CTS, -, Yes - D25, PA10, -, 1_CH3, -, 1_RX, -, Yes - D26, PA9, -, 1_CH2, -, 1_TX, -, Yes - D27, PA8, -, 1_CH1, -, 1_CK, -, Yes - D28, PB15, -, -, -, -, 2_MOSI, Yes - D29, PB14, -, -, -, 3_RTS, 2_MISO, Yes - D30, PB13, -, -, -, 3_CTS, 2_SCK, Yes - D31, PB12, -, 1_BKIN, 2_SMBA, 3_CK, 2_NSS, Yes - D32, PB8, -, 4_CH3, -, -, -, Yes - D33, PB1, CH9, 3_CH4, -, -, -, - - -.. _maple-mini-gpio-port-map: - -GPIO Port Pin Map -^^^^^^^^^^^^^^^^^ -The following table shows what pins are associated with each -:ref:`GPIO port `. - -.. csv-table:: - :header: GPIOA, GPIOB, GPIOC - - PA0: D11, PB0: D3, PC0: - - PA1: D10, PB1: D33, PC1: - - PA2: D9, PB2: D2, PC2: - - PA3: D8, PB3: D19, PC3: - - PA4: D7, PB4: D18, PC4: - - PA5: D6, PB5: D17, PC5: - - PA6: D5, PB6: D16, PC6: - - PA7: D4, PB7: D15, PC7: - - PA8: D27, PB8: D32, PC8: - - PA9: D26, PB9: -, PC9: - - PA10: D25, PB10: D1, PC10: - - PA11: D24, PB11: D0, PC11: - - PA12: D23, PB12: D31, PC12: - - PA13: D22, PB13: D30, PC13: D14 - PA14: D21, PB14: D29, PC14: D13 - PA15: D20, PB15: D28, PC15: D12 - -.. _maple-mini-timer-map: - -Timer Pin Map -^^^^^^^^^^^^^ - -The following table shows what pins are associated with a particular -timer's capture/compare channels. - -.. csv-table:: - :header: Timer, Ch. 1, Ch. 2, Ch. 3, Ch. 4 - :delim: | - - 1 | D27 | D26 | D25 | D24 - 2 | D11 | D10 | D9 | D8 - 3 | D5 | D4 | D3 | :ref:`D33 ` - 4 | D16 | D15 | :ref:`D32 ` | - -.. _maple-mini-exti-map: - -EXTI Line Pin Map -^^^^^^^^^^^^^^^^^ - -The following table shows which pins connect to which :ref:`EXTI lines -`. - -.. list-table:: - :widths: 1 1 - :header-rows: 1 - - * - EXTI Line - - Pins - * - EXTI0 - - D3, D11 - * - EXTI1 - - D10, D33 - * - EXTI2 - - D2, D9 - * - EXTI3 - - D8, D19 - * - EXTI4 - - D7, D18 - * - EXTI5 - - D6, D17 - * - EXTI6 - - D5, D16 - * - EXTI7 - - D4, D15 - * - EXTI8 - - D27, D32 - * - EXTI9 - - D26 - * - EXTI10 - - D1, D25 - * - EXTI11 - - D0, D24 - * - EXTI12 - - D23, D31 - * - EXTI13 - - D14, D22, D30 - * - EXTI14 - - D13, D21, D29 - * - EXTI15 - - D12, D20, D28 - -.. _maple-mini-usart-map: - -USART Pin Map -^^^^^^^^^^^^^ - -The Maple Mini has three serial ports (also known as :ref:`USARTs -`). They communicate using the pins given in the following -table. - -.. csv-table:: - :header: Serial Port, TX, RX, CK, CTS, RTS - :delim: | - - ``Serial1`` | D26 | D25 | D27 | D24 | D23 - ``Serial2`` | D9 | D8 | D7 | D11 | D10 - ``Serial3`` | D1 | D0 | D31 | D30 | D29 - -.. _maple-mini-adc-bank: - -Low-Noise ADC Pins -^^^^^^^^^^^^^^^^^^ - -Maple Mini has an electrically isolated analog power plane with its -own regulator, and a geometrically isolated ground plane, connected to -the digital plane by an inductor. Its analog input pins, D3 — D11, -are laid out to correspond with these analog planes, and our -measurements indicate that they generally offer low noise ADC -performance. However, analog performance may vary depending upon the -activity of the other GPIOs. Consult the :ref:`Maple Mini hardware -design files ` for more details. - -.. _maple-mini-board-values: - -Board-Specific Values ---------------------- - -This section lists the Maple Mini's :ref:`board-specific values -`. - -- ``CYCLES_PER_MICROSECOND``: 72 -- ``BOARD_BUTTON_PIN``: 32 -- ``BOARD_LED_PIN``: 33 -- ``BOARD_NR_GPIO_PINS``: 34 -- ``BOARD_NR_PWM_PINS``: 12 -- ``boardPWMPins``: 3, 4, 5, 8, 9, 10, 11, 15, 16, 25, 26, 27 -- ``BOARD_NR_ADC_PINS``: 9 -- ``boardADCPins``: 3, 4, 5, 6, 7, 8, 9, 10, 11 -- ``BOARD_NR_USED_PINS``: 4 -- ``boardUsedPins``: ``BOARD_LED_PIN``, ``BOARD_BUTTON_PIN``, 23, 24 - (23 and 24 are used by :ref:`USB `) -- ``BOARD_NR_USARTS``: 3 -- ``BOARD_USART1_TX_PIN``: 26 -- ``BOARD_USART1_RX_PIN``: 25 -- ``BOARD_USART2_TX_PIN``: 9 -- ``BOARD_USART2_RX_PIN``: 8 -- ``BOARD_USART3_TX_PIN``: 1 -- ``BOARD_USART3_RX_PIN``: 0 -- ``BOARD_NR_SPI``: 2 -- ``BOARD_SPI1_NSS_PIN``: 7 -- ``BOARD_SPI1_MOSI_PIN``: 4 -- ``BOARD_SPI1_MISO_PIN``: 5 -- ``BOARD_SPI1_SCK_PIN``: 6 -- ``BOARD_SPI2_NSS_PIN``: 31 -- ``BOARD_SPI2_MOSI_PIN``: 28 -- ``BOARD_SPI2_MISO_PIN``: 29 -- ``BOARD_SPI2_SCK_PIN``: 30 -- ``BOARD_JTMS_SWDIO_PIN``: 22 -- ``BOARD_JTCK_SWCLK_PIN``: 21 -- ``BOARD_JTDI_PIN``: 20 -- ``BOARD_JTDO_PIN``: 19 -- ``BOARD_NJTRST_PIN``: 18 - -.. _maple-mini-hardware: - -Hardware Design Files ---------------------- - -The hardware schematics and board layout files are available in the -`Maple Mini GitHub repository `_. - -From the GitHub repository main page, you can download the entire -repository by clicking the "Download" button. If you are familiar -with `Git `_, you can also clone the repository -at the command line with :: - - $ git clone git://github.com/leaflabs/maplemini.git - -Failure Modes -------------- - -The following known failure modes apply to all Maple boards. The -failure modes aren't design errors, but are easy ways to break or -damage your board permanently. - -* **High voltage on non-tolerant pins**: not all header pins are 5 V - compatible; so e.g. connecting certain serial devices in the wrong - way could over-voltage the pins. The :ref:`pin-mapping master table - ` details which pins are :ref:`5 - V-tolerant `. - -Errata ------- - -This section lists known issues and warnings for the Maple Mini Rev 2 -(the first Rev sold to the public). - -.. _maple-mini-vin: - -* **Silkscreen Vin voltage mistake**: The silkscreen on the Maple Mini - falsely indicates that Vin may be supplied with up to 16V. We - recommend an input voltage **no greater than 12V**, and potentially - even lower depending upon the current draw requirements of the - application. Please see :ref:`Power Regulation on the Maple Mini - ` for more information. - - -Recommended Reading -------------------- - -.. _maple-mini-stdocs: - -STMicro documentation for STM32F103CB microcontroller: - -* `Datasheet - `_ - (PDF); covers STM32F103x8, STM32F103xB. -* `Reference Manual RM0008 - `_ - (PDF); definitive resource for peripherals on the STM32F1 line. -* `Programming Manual PM0056 - `_ - (PDF); assembly language and register reference. -* `STM32F103CB `_ - overview page with links to further references. - -.. rubric:: Footnotes - -.. [#fusedpins] See :ref:`boardUsedPins ` - for more information. diff --git a/docs/source/hardware/maple-native-beta.rst b/docs/source/hardware/maple-native-beta.rst deleted file mode 100644 index bdfd216..0000000 --- a/docs/source/hardware/maple-native-beta.rst +++ /dev/null @@ -1,605 +0,0 @@ -.. highlight:: sh - -.. _maple-native-b: - -Maple Native β -============== - -This page is a general resource for information specific to the Maple -Native Beta. Since this is a beta release, the information here may -change slightly between now and the final Maple Native release. - -.. contents:: Contents - :local: - -Technical Specifications ------------------------- - -* MCU: `STM32F103ZET6 `, a 32-bit ARM Cortex M3 - microprocessor. -* Clock Speed: **72 MHz** -* **512 KB Flash**, **64 KB SRAM** (on-chip), **1 MB SRAM** (external) -* 106 :ref:`digital I/O pins ` -* 17 :ref:`PWM ` pins at 16 bit resolution -* 21 :ref:`analog input (ADC) ` pins at 12-bit resolution -* 3 :ref:`SPI ` peripherals -* 2 :ref:`I2C ` peripherals -* 12 Channels of Direct Memory Access (**DMA**) (:ref:`libmaple-dma`) - with 2 DMA controllers -* 3 :ref:`USART (serial port) ` peripherals, 2 **UART** peripherals -* 2 advanced, 4 general-purpose, and 2 basic :ref:`timers ` -* Dedicated :ref:`USB ` port for programming and communications -* :ref:`JTAG ` -* Nested Vectored Interrupt Controller (NVIC) (including - :ref:`external interrupt ` on GPIOs) -* Supplies up to 500 mA at 3.3 V, with :ref:`separate 250 mA digital - and analog regulators ` for low-noise analog - performance -* :ref:`Open-source, four layer design ` -* Support for low power, sleep, and standby modes (<500 μA) -* Operating Voltage: 3.3 V -* Input Voltage (recommended): 3 V — 12 V -* Dimensions: 4″ × 2.1″ - -.. _maple-native-b-powering: - -Powering the Maple Native -------------------------- - -The power source is determined by the header labeled "PWRSEL" on the -silkscreen. The Maple Native may be powered from USB (marked "USB" on -the PWRSEL header), a LiPo battery (marked "BAT"), or one of the two -"Vin" pins (marked "EXT"). Boards are shipped with a jumper on the -USB selector. In order to power it off of an alternative source, -unplug the Maple Native, then move the jumper to the desired selector -before reconnecting power. - -The "Vin" line is available on the pin labeled "Vin" on the vertical -header to the right of the PWRSEL header, as well as on the -unpopulated two-pin connector on the upper left corner of the -board. On this latter connector, polarity was accidentally left -unmarked: the leftmost, round pin should be power, while the square -pin should be ground. - -When powering the Maple Native board from a battery or the Vin lines, -care must be taken not to over-voltage the board. In general, an upper -limit of 12V input is acceptable, but this may vary depending upon the -current draw requirements of the application. Please see :ref:`Power -Regulation on the Maple Native ` for -more information. - -.. _maple-native-b-power-regulation: - -Power Regulation on the Maple Native ------------------------------------- - -Power regulation on the Maple Native is provided by two low dropout -linear voltage regulators. (The part is the MCP1703 from Microchip, in -the SOT-23A package. You can download the datasheet `here -`_). One -of the regulators supplies power to the digital voltage plane; the -other supplies power to the analog voltage plane. - -These voltage regulators nominally take an input of up to 16V. In -addition, while the maximum continuous output current for the board is -250mA, if you are powering the board off higher voltages the current -it can supply goes down, due to the regulators needing to dissipate -the extra power. So if you are powering the board off 12V, the max -current is about 40mA at room temperature. In general (again, at room -temperature) the max power dissipation (PD) for the chip is about -.37W, and output current = PD/(Vin-Vout). For exact max current -calculations, please refer to the datasheet linked above. - -If you are planning to draw a lot of current from the Maple Native -board, it is necessary to provide input power as close to 3.3V as -possible. Powering the microcontroller circuitry and LEDs on the board -alone takes approximately 30mA, so if you are powering the board with -12V that leaves only 10mA (at best) available for powering any user -circuitry. Attempting to draw more than 10mA runs the risk of shorting -out the power regulators and bricking your board. - -Using the Built-in Battery Charger ----------------------------------- - -Maple Native includes a built-in LiPo battery charger. In order to -use it, put a jumper across the CHRG selector on the PWRSEL header and -across the USB, or EXT selectors, depending on whether you're charging -the battery via USB cable or Vin, respectively. The LED labeled CHRG -will light up while the battery is being charged. When the battery is -finished charging, the LED labeled DONE will light up. - -.. _maple-native-b-gpios: - -GPIO Information ----------------- - -The Maple Native features 106 total input/output pins, numbered ``D0`` -through ``D105``. In most cases, these numbers correspond to the -numeric values next to each header on the Maple Native's silkscreen. -However, pins ``D101`` through ``D105`` are broken out to the -:ref:`JTAG ` header, and are not numbered on the silkscreen. In -addition, some other pins have other uses by default [#fusedpins]_. - -.. _maple-native-b-but: - -Pin ``D6`` is the Native's :ref:`button pin `. -It is thus mainly useful as an :ref:`input `. The -pin will :ref:`read ` ``HIGH`` when the :ref:`button -is pressed `. - -.. _maple-native-b-led: - -Pin ``D22`` is the Native's :ref:`LED pin `. -It is thus mainly useful as an :ref:`output `. The -LED will glow when ``HIGH`` is :ref:`written ` to -it. - -.. _maple-native-b-fsmc: - -Many of the pins on the right header (pins ``D56`` through ``D100``, -the header is labeled :ref:`"FSMC" ` on the silkscreen) are -connected to the SRAM chip. Using these pins as GPIOs may render the -memory chip useless, which can cause your program to crash. For this -reason, we don't recommend that you use these pins unless you know -what you are doing. The following pins on the right header are not -connected to the SRAM and may be used with impunity: ``D57``, ``D60``, -``D63``, ``D66``, ``D69``, ``D72``, ``D75``, ``D80``, ``D83``. - -.. _maple-native-b-jtag: - -Pins ``D101`` through ``D105`` are connected to the pads on the -:ref:`JTAG ` header. In order to use them as GPIOs, you must -first disable the Maple Native's debug ports. You can do this by -calling :ref:`lang-disabledebugports`. (Note that this means you -won't be able to use JTAG or SW-Debug to debug your program). - -.. TODO [0.1.0] silkscreen pictures - -.. _maple-native-b-pin-map-master: - -Master Pin Map -^^^^^^^^^^^^^^ - -This table shows a summary the available functionality on every GPIO -pin, by peripheral type. The "5 V?" column documents whether or not -the pin is :ref:`5 volt tolerant `. - -Note that this table is not exhaustive; on some pins, more peripherals -are available than are listed here. - -**Top header:** - -.. csv-table:: - :header: Pin, :ref:`GPIO `, :ref:`ADC `, :ref:`Timer `, :ref:`I2C `, :ref:`UART `, :ref:`SPI `, 5 V? - - D0, PB10, -, -, 2_SCL, 3_TX, -, Yes - D1, PB11, -, -, 2_SDA, 3_RX, -, Yes - D2, PB12, -, 1_BKIN, 2_SMBA, 3_CK, 2_NSS, Yes - D3, PB13, -, -, -, 3_CTS, 2_SCK, Yes - D4, PB14, -, -, -, 3_RTS, 2_MISO, Yes - D5, PB15, -, -, -, -, 2_MOSI, Yes - D6, PG15, -, -, -, -, -, Yes - D7, PC0, 1_CH10, -, -, -, -, - - D8, PC1, 1_CH11, -, -, -, -, - - D9, PC2, 1_CH12, -, -, -, -, - - D10, PC3, 1_CH13, -, -, -, -, - - D11, PC4, 1_CH14, -, -, -, -, - - D12, PC5, 1_CH15, -, -, -, -, - - D13, PC6, -, 8_CH1, -, -, -, Yes - D14, PC7, -, 8_CH2, -, -, -, Yes - D15, PC8, -, 8_CH3, -, -, -, Yes - D16, PC9, -, 8_CH4, -, -, -, Yes - D17, PC10, -, -, -, 4_TX, -, Yes - D18, PC11, -, -, -, 4_RX, -, Yes - D19, PC12, -, -, -, 5_TX, -, Yes - D20, PC13, -, -, -, -, -, - - D21, PC14, -, -, -, -, -, - - D22, PC15, -, -, -, -, -, - - D23, PA8, -, 1_CH1, -, 1_CK, -, Yes - D24, PA9, -, 1_CH2, -, 1_TX, -, Yes - D25, PA10, -, 1_CH3, -, 1_RX, -, Yes - D26, PB9, -, 4_CH4, -, -, -, Yes - -**Bottom header:** - -.. note:: ``D48``, ``D49``, ``D50``, ``D51`` are also connected to - Timer 2 channels 1, 2, 3, and 4, respectively. - -.. csv-table:: - :header: Pin, :ref:`GPIO `, :ref:`ADC `, :ref:`Timer `, :ref:`I2C `, :ref:`UART `, :ref:`SPI `, 5 V? - - D27, PD2, -, 3_ETR, -, 5_RX, -, Yes - D28, PD3, -, -, -, -, -, Yes - D29, PD6, -, -, -, -, -, Yes - D30, PG11, -, -, -, -, -, Yes - D31, PG12, -, -, -, -, -, Yes - D32, PG13, -, -, -, -, -, Yes - D33, PG14, -, -, -, -, -, Yes - D34, PG8, -, -, -, -, -, Yes - D35, PG7, -, -, -, -, -, Yes - D36, PG6, -, -, -, -, -, Yes - D37, PB5, -, -, 1_SMBA, -, 3_MOSI, - - D38, PB6, -, 4_CH1, 1_SCL, -, -, Yes - D39, PB7, -, 4_CH2, 1_SDA, -, -, Yes - D40, PF11, -, -, -, -, -, Yes - D41, PF6, 3_CH4, -, -, -, -, - - D42, PF7, 3_CH5, -, -, -, -, - - D43, PF8, 3_CH6, -, -, -, -, - - D44, PF9, 3_CH7, -, -, -, -, - - D45, PF10, 3_CH8, -, -, -, -, - - D46, PB1, 1_CH9, 3_CH4, -, -, -, - - D47, PB0, 1_CH8, 3_CH3, -, -, -, - - D48, PA0, 1_CH0, 5_CH1, -, 2_CTS, -, - - D49, PA1, 1_CH1, 5_CH2, -, 2_RTS, -, - - D50, PA2, 1_CH2, 5_CH3, -, 2_TX, -, - - D51, PA3, 1_CH3, 5_CH4, -, 2_RX, -, - - D52, PA4, 1_CH4, -, -, 2_CK, 1_NSS, - - D53, PA5, 1_CH5, -, -, -, 1_SCK, - - D54, PA6, 1_CH6, 3_CH1, -, -, 1_MISO, - - D55, PA7, 1_CH7, 3_CH2, -, -, 1_MOSI, - - -.. _maple-native-b-fsmc-map: - -**Right (FSMC) header** - -All of the following pins are 5V-tolerant. Note that in the "FSMC" -column below, entries with a "Dn" value (D0, D1, etc.) don't refer to -pins; they refer to FSMC data lines. See :ref:`RM0008 -` for more information. - -.. warning:: Many of the pins on this header are used by the Maple - Native's SRAM chip. Don't use them as GPIOs unless you know what - you're doing, or your program may crash. :ref:`See above - ` for more information. - -.. csv-table:: - :header: Pin, :ref:`GPIO `, :ref:`FSMC ` - - D56, PF0, A0 - D57, PD11, A16 - D58, P14, D0 - D59, PF1, A1 - D60, PD12, A17 - D61, PD15, D1 - D62, PF2, A2 - D63, PD13, A18 - D64, PD0, D2 - D65, PF3, A3 - D66, PE3, A19 - D67, PD1, D3 - D68, PF4, A4 - D69, PE4, A20 - D70, PE7, D4 - D71, PF5, A5 - D72, PE5, A21 - D73, PE8, D8 - D74, PF12, A6 - D75, PE6, A22 - D76, PE9, D6 - D77, PF13, A7 - D78, PE10, D7 - D79, PF14, A8 - D80, PG9, NE2/NCE3 - D81, PE11, D8 - D82, PF15, A9 - D83, PG10, NCE4_1/NE3/NCE4_2 - D84, PE12, D9 - D85, PG0, A10 - D86, PD5, NWE - D87, PE13, D10 - D88, PG1, A11 - D89, PD4, NOE - D90, PE14, D11 - D91, PG2, A12 - D92, PE1, NBL1 - D93, PE15, D12 - D94, PG3, A13 - D95, PE0, NBL0 - D96, PD8, D13 - D97, PG4, A14 - D98, PD9, D14 - D99, PG5, A15 - D100, PD10, D15 - -**JTAG header pins** - -.. note:: See :ref:`above ` for more information on - these pins. - -.. csv-table:: - :header: Pin, :ref:`GPIO `, :ref:`SPI `, 5 V? - - D101, PA13, -, Yes - D102, PA14, -, Yes - D103, PA15, 3_NSS, Yes - D104, PB3, 3_SCK, Yes - D105, PB4, 3_MISO, Yes - -.. _maple-native-b-gpio-port-map: - -GPIO Port Pin Map -^^^^^^^^^^^^^^^^^ - -The following tables show what pins are associated with each -:ref:`GPIO port `. - -.. csv-table:: - :header: GPIOA, GPIOB, GPIOC, GPIOD - - PA0: D48, PB0: D47, PC0: D7, PD0: D64 - PA1: D49, PB1: D46, PC1: D8, PD1: D67 - PA2: D50, PB2: -, PC2: D9, PD2: D27 - PA3: D51, PB3: D104, PC3: D10, PD3: D28 - PA4: D52, PB4: D105, PC4: D11, PD4: D89 - PA5: D53, PB5: D37, PC5: D12, PD5: D86 - PA6: D54, PB6: D38, PC6: D13, PD6: D29 - PA7: D55, PB7: D39, PC7: D14, PD7: - - PA8: D23, PB8: -, PC8: D15, PD8: D96 - PA9: D24, PB9: D26, PC9: D16, PD9: D98 - PA10: D25, PB10: D0, PC10: D17, PD10: D100 - PA11: -, PB11: D1, PC11: D18, PD11: D57 - PA12: -, PB12: D2, PC12: D19, PD12: D60 - PA13: D101, PB13: D3, PC13: D20, PD13: D63 - PA14: D102, PB14: D4, PC14: D21, PD14: D58 - -.. csv-table:: - :header: GPIOE, GPIOF, GPIOG - - PE0: D95, PF0: D56, PG0: D85 - PE1: D92, PF1: D59, PG1: D88 - PE2: - PF2: D62, PG2: D91, - PE3: D66, PF3: D65, PG3: D94 - PE4: D69, PF4: D68, PG4: D97 - PE5: D72, PF5: D71, PG5: D99 - PE6: D75, PF6: D41, PG6: D36 - PE7: D70, PF7: D42, PG7: D35 - PE8: D73, PF8: D43, PG8: D34 - PE9: D76, PF9: D44, PG9: D80 - PE10: D78, PF10: D45, PG10: D83 - PE11: D81, PF11: D40, PG11: D30 - PE12: D84, PF12: D74, PG12: D31 - PE13: D87, PF13: D77, PG13: D32 - PE14: D90, PF14: D79, PG14: D33 - -.. _maple-native-b-timer-map: - -Timer Pin Map -^^^^^^^^^^^^^ - -The following table shows what pins are associated with a particular -timer's capture/compare channels. - -There is no mistake between timers 2 and 5. They really do share -those pins. If you like, you can remap some of the timer 2 channels -to get extra PWM pins; see :ref:`afio_remap() (in gpio.h) -`. - -.. csv-table:: - :header: Timer, Ch. 1, Ch. 2, Ch. 3, Ch. 4 - :delim: | - - 1 | D23 | D24 | D25 | - 2 | D48 | D49 | D50 | D51 - 3 | D54 | D55 | D47 | D46 - 4 | D38 | D39 | | D26 - 5 | D48 | D49 | D50 | D51 - 8 | D13 | D14 | D15 | D16 - -.. _maple-native-b-exti-map: - -EXTI Line Pin Map -^^^^^^^^^^^^^^^^^ - -The following table shows which pins connect to which :ref:`EXTI lines -`. - -.. list-table:: - :widths: 1 3 - :header-rows: 1 - - * - EXTI Line - - Pins - * - EXTI0 - - D7, D47, D48, D56, D64, D85, D95 - * - EXTI1 - - D8, D46, D49, D59, D67, D88, D92 - * - EXTI2 - - D9, D27, D50, D62, D91 - * - EXTI3 - - D10, D28, D51, D65, D66, D94, D104 - * - EXTI4 - - D11, D52, D68, D69, D89, D97, D105 - * - EXTI5 - - D12, D37, D53, D71, D72, D86, D99 - * - EXTI6 - - D13, D29, D36, D38, D41, D54, D75 - * - EXTI7 - - D14, D35, D39, D42, D55, D70 - * - EXTI8 - - D15, D23, D34, D43, D73, D96 - * - EXTI9 - - D16, D24, D26, D44, D76, D80, D98 - * - EXTI10 - - D0, D17, D25, D45, D78, D83, D100 - * - EXTI11 - - D1, D18, D30, D40, D57, D81 - * - EXTI12 - - D2, D19, D31, D60, D74, D84 - * - EXTI13 - - D3, D20, D32, D63, D77, D87, D101 - * - EXTI14 - - D4, D21, D33, D58, D79, D90, D102 - * - EXTI15 - - D5, D6, D22, D61, D82, D93, D103 - -.. _maple-native-b-usart-map: - -USART Pin Map -^^^^^^^^^^^^^ - -The Maple Native has 3 :ref:`USART ` serial ports. They -communicate using the pins given in the following table. - -.. csv-table:: - :header: Serial port, TX, RX, CK, CTS, RTS - :delim: | - - ``Serial1`` | D24 | D25 | D23 | | - ``Serial2`` | D50 | D51 | D52 | D48 | D49 - ``Serial3`` | D0 | D1 | D2 | D3 | D4 - -The Maple Native also has 2 UART serial ports. Unlike USARTS, these -only communicate asynchronously, and thus only have TX and RX pins. -These are given in the following table. - -.. csv-table:: - :header: Serial port, TX, RX - :delim: | - - ``Serial4`` | D17 | D18 - ``Serial5`` | D19 | D27 - -.. _maple-native-b-adc-bank: - -Low-Noise ADC Pins -^^^^^^^^^^^^^^^^^^ - -There are fifteen pins at the bottom right of the board (``D41`` — -``D55``) that generally offer lower-noise ADC performance than other -pins on the board. If you're concerned about getting good ADC -readings, we recommend using one of these pins to take your -measurements. - -Maple Native has an electrically isolated analog power plane with its -own regulator, and a geometrically isolated ground plane. Analog input -pins D41 — D55 are laid out to correspond with these analog planes, -and our measurements indicate that they generally ofer low noise ADC -performance. However, analog performance may vary depending upon the -activity of other GPIOs. In particular, using PWM on any of pins -``D46`` — ``D51``, ``D54``, and ``D55`` may cause digital noise. -Consult the :ref:`Maple Native beta hardware design files -` for more details. - -.. _maple-native-b-board-values: - -Board-Specific Values ---------------------- - -This section lists the Maple Native's :ref:`board-specific values -`. - -- ``CYCLES_PER_MICROSECOND``: 72 -- ``BOARD_BUTTON_PIN``: 6 -- ``BOARD_LED_PIN``: 22 -- ``BOARD_NR_GPIO_PINS``: 106 -- ``BOARD_NR_PWM_PINS``: 18 -- ``boardPWMPins``: 13, 14, 15, 16, 23, 24, 25, 26, 38, 39, 46, 47, - 48, 49, 50, 51, 54, 55 -- ``BOARD_NR_ADC_PINS``: 21 -- ``boardADCPins``: 7, 8, 9, 10, 11, 12, 41, 42, 43, 44, 45, 46, 47, - 48, 49, 50, 51, 52, 53, 54, 55 -- ``BOARD_NR_USED_PINS``: 43 -- ``boardUsedPins``: ``BOARD_LED_PIN``, ``BOARD_BUTTON_PIN``, - ``BOARD_JTMS_SWDIO_PIN``, ``BOARD_JTCK_SWCLK_PIN``, - ``BOARD_JTDI_PIN``, ``BOARD_JTDO_PIN``, ``BOARD_NJTRST_PIN``, and - all pins on FSMC header except those mentioned :ref:`above - `. -- ``BOARD_NR_USARTS``: 5 -- ``BOARD_USART1_TX_PIN``: 24 -- ``BOARD_USART1_RX_PIN``: 25 -- ``BOARD_USART2_TX_PIN``: 50 -- ``BOARD_USART2_RX_PIN``: 51 -- ``BOARD_USART3_TX_PIN``: 0 -- ``BOARD_USART3_RX_PIN``: 1 -- ``BOARD_UART4_TX_PIN``: 17 -- ``BOARD_UART4_RX_PIN``: 18 -- ``BOARD_UART5_TX_PIN``: 19 -- ``BOARD_UART5_RX_PIN``: 27 -- ``BOARD_NR_SPI``: 3 -- ``BOARD_SPI1_NSS_PIN``: 52 -- ``BOARD_SPI1_MOSI_PIN``: 55 -- ``BOARD_SPI1_MISO_PIN``: 54 -- ``BOARD_SPI1_SCK_PIN``: 53 -- ``BOARD_SPI2_NSS_PIN``: 2 -- ``BOARD_SPI2_MOSI_PIN``: 5 -- ``BOARD_SPI2_MISO_PIN``: 4 -- ``BOARD_SPI2_SCK_PIN``: 3 -- ``BOARD_SPI3_NSS_PIN``: 103 (on :ref:`JTAG header `) -- ``BOARD_SPI3_MOSI_PIN``: 37 -- ``BOARD_SPI3_MISO_PIN``: 105 (JTAG header) -- ``BOARD_SPI3_SCK_PIN``: 104 (JTAG header) -- ``BOARD_JTMS_SWDIO_PIN``: :ref:`103 ` -- ``BOARD_JTCK_SWCLK_PIN``: 102 -- ``BOARD_JTDI_PIN``: 103 -- ``BOARD_JTDO_PIN``: 104 -- ``BOARD_NJTRST_PIN``: 105 - -.. _maple-native-b-hardware: - -Hardware Design Files -^^^^^^^^^^^^^^^^^^^^^ - -The hardware schematics and board layout files are available in the -`Maple Native GitHub repository -`_. Download the `beta -version's hardware design files -`_ (ZIP format). - -If you're familiar with Git, you can clone the entire repository and -checkout the commit tagged "beta" using the following:: - - $ git clone git://github.com/leaflabs/maplenative.git - $ git checkout beta - -Failure Modes -------------- - -The following known failure modes apply to the Maple Native Beta. The -failure modes aren't design errors, but are easy ways to break or -damage your board permanently. - -* **Reversing Vin and GND**: when powering the Maple Native Beta via - the Vin and ground (GND) pins at the top left of the board, it is - possible to carelessly cause a short or switch the connections, - applying the high voltage to GND and ground to Vin. - - If this happens, you will reverse bias the diode beneath these pins, - most likely damaging it. This may cause excess voltage to - subsequently be delivered to the board once the reversed pins are - connected properly. - -Errata ------- - -This section lists known issues and warnings for the Maple Native -Beta. - -* **PWM on pin 39**: PWM on pin 39 appears to be nonfunctional. We - are looking into this issue. - -* **VREF is nonfunctional**: Due to a routing error, VREF is - permanently tied to 3.3V at VAA. - -Recommended Reading -------------------- - -.. _maple-native-b-stdocs: - -STMicro documentation for STM32F103ZE microcontroller: - -* `Datasheet - `_ - (PDF); covers STM32F103xC, STM3F103xD, STM32F103xE. -* `Reference Manual RM0008 - `_ - (PDF); definitive resource for peripherals on the STM32F1 line. -* `Programming Manual PM0056 - `_ - (PDF); assembly language and register reference. -* `STM32F103RE `_ - overview page with links to further references. - -.. rubric:: Footnotes - -.. [#fusedpins] See :ref:`boardUsedPins ` - for more information. diff --git a/docs/source/hardware/maple-native.rst b/docs/source/hardware/maple-native.rst deleted file mode 100644 index 79115fc..0000000 --- a/docs/source/hardware/maple-native.rst +++ /dev/null @@ -1,6 +0,0 @@ -.. _hardware-maple-native: - -Maple Native -============ - -Stub. diff --git a/docs/source/hardware/maple-ret6.rst b/docs/source/hardware/maple-ret6.rst deleted file mode 100644 index 3d2d037..0000000 --- a/docs/source/hardware/maple-ret6.rst +++ /dev/null @@ -1,466 +0,0 @@ -.. highlight:: sh - -.. _maple-ret6: - -Maple RET6 Edition -================== - -This page is a general resource for information specific to the Maple -RET6 Edition. The Maple RET6 Edition is a "beta" board released as a -simple way to get a more powerful chip (the STM32F103\ **RET6**, hence -the name) than the one on the base Maple (the STM32F103\ **RBT6**) in -the hands of Maple developers. - -.. contents:: Contents - :local: - -.. TODO [dma.rst] Ref to source/dma.rst in sequel instead of libmaple-dma -.. TODO [dac.rst] Ref to source/dac.rst in sequel instead of libmaple-dac -.. TODO [nvic.rst] Ref to source/nvic.rst in sequel - -Technical Specifications ------------------------- - -* MCU: :ref:`STM32F103RET6 `, a 32-bit ARM Cortex - M3 microprocessor -* Clock Speed: **72 MHz** -* **512 KB Flash** and **64 KB SRAM** -* 43 :ref:`digital I/O pins (GPIOs) ` -* 18 :ref:`PWM ` pins at 16 bit resolution -* 15 :ref:`analog input (ADC) ` pins at 12 bit resolution -* Built-in, 2 channel **DAC** at 12 bit resolution (:ref:`libmaple-dac`). -* 2 :ref:`SPI ` peripherals with **I2S** support -* 2 :ref:`I2C ` peripherals -* 12 Channels of Direct Memory Access (**DMA**) (:ref:`libmaple-dma`) - with 2 DMA controllers -* 3 :ref:`USART (serial port) ` peripherals -* 2 advanced, 4 general-purpose, and 2 basic :ref:`timers ` -* Dedicated :ref:`USB ` port for programming and communications -* :ref:`JTAG ` -* Nested Vectored Interrupt Controller (NVIC) (including - :ref:`external interrupt ` on GPIOs) -* Supplies up to 500 mA at 3.3 V, with :ref:`separate 250 mA digital - and analog regulators ` for low-noise analog - performance -* :ref:`Open-source, four layer design ` -* Support for low power, sleep, and standby modes (<500 μA) -* Operating Voltage: 3.3 V -* Input Voltage (recommended): 4 V — 12 V -* Dimensions are 2.05″ × 2.1″ - -.. _maple-ret6-powering: - -Powering the Maple RET6 Edition -------------------------------- - -The Maple RET6 Edition is powered in the :ref:`same way as the -standard Maple `. - -.. warning:: The RET6 Edition silkscreen falsely indicates that the - barrel jack accepts up to 18 V. We recommend a barrel jack input - voltage **no greater than 12V**, and potentially even lower - depending upon the current draw requirements of the - application. The same goes for powering off LiPo batteries. - - Please see :ref:`Power Regulation on the Maple - ` for more information. - -.. _maple-ret6power-regulation: - -Power Regulation on the Maple RET6 ----------------------------------- - -Power regulation on the Maple RET6 works in the :ref:`same way as the -standard Maple `. - -Using the Built-in Battery Charger ----------------------------------- - -The RET6 Edition has a built-in LiPo battery charger. In order to use -it, put a jumper across the CHRG header on the power selection header -and across the USB, or EXT selectors, depending on whether you're -charging the battery via USB cable or barrel jack connector. The LED -labeled CHRG will light up while the battery is being charged. When -the battery is finished charging, the LED labeled DONE will light up. - -.. _maple-ret6-gpios: - -GPIO Information ----------------- - -The RET6 Edition features 38 ready-to-use general purpose input/output -(see :ref:`gpio`) pins for digital input/output, numbered ``D0`` -through ``D37``. These numbers correspond to the numeric values next -to each header on the Maple silkscreen. - -.. _maple-ret6-but: - -Pin ``D38`` is the board's :ref:`button pin `. -It is thus mainly useful as an :ref:`input `. The -pin will :ref:`read ` ``HIGH`` when the :ref:`button -is pressed `. - -More GPIOs (numbered ``D39``\ --``D42`` on the back of the RET6 -Edition's silkscreen) are available if you use the -:ref:`lang-disabledebugports` function; see the :ref:`board-specific -debug pin constants ` for more information. -(See :ref:`this erratum ` for information about -the pin numbered ``43`` on the silkscreen). - -.. TODO [0.1.0] silkscreen pictures which expand abbreviations - -.. _maple-ret6-pin-map-master: - -Master Pin Map -^^^^^^^^^^^^^^ - -This table shows a summary of the available functionality on every -GPIO pin, by peripheral type. The "5 V?" column documents whether or -not the pin is :ref:`5 volt tolerant `. - -Note that this table is not exhaustive; on some pins, more peripherals -are available than are listed here. - -.. csv-table:: - :header: Pin, :ref:`GPIO `, :ref:`ADC `, :ref:`Timer `, :ref:`I2C `, :ref:`UART/USART `, :ref:`SPI `, 5 V? - - D0, PA3, CH3, 2_CH4, -, 2_RX, -, - - D1, PA2, CH2, 2_CH3, -, 2_TX, -, - - D2, PA0, CH0, 2_CH1_ETR, -, 2_CTS, -, - - D3, PA1, CH1, 2_CH2, -, 2_RTS, -, - - D4, PB5, -, -, 1_SMBA, -, 3_MOSI, - - D5, PB6, -, 4_CH1, 1_SCL, -, -, Yes - D6, PA8, -, 1_CH1, -, 1_CK, -, Yes - D7, PA9, -, 1_CH2, -, 1_TX, -, Yes - D8, PA10, -, 1_CH3, -, 1_RX, -, Yes - D9, PB7, -, 4_CH2, 1_SDA, -, -, Yes - D10, PA4, CH4, -, -, 2_CK, 1_NSS, - - D11, PA7, CH7, 3_CH2, -, -, 1_MOSI, - - D12, PA6, CH6, 3_CH1, -, -, 1_MISO, - - D13, PA5, CH5, -, -, -, 1_SCK, - - D14, PB8, -, 4_CH3, -, -, -, Yes - D15, PC0, CH10, -, -, -, -, - - D16, PC1, CH11, -, -, -, -, - - D17, PC2, CH12, -, -, -, -, - - D18, PC3, CH13, -, -, -, -, - - D19, PC4, CH14, -, -, -, -, - - D20, PC5, CH15, -, -, -, -, - - D21, PC13, -, -, -, -, -, - - D22, PC14, -, -, -, -, -, - - D23, PC15, -, -, -, -, -, - - D24, PB9, -, 4_CH4, -, -, -, Yes - D25, PD2, -, 3_ETR, -, -, 5_RX, Yes - D26, PC10, -, -, -, -, 4_TX, Yes - D27, PB0, CH8, 3_CH3, -, -, -, - - D28, PB1, CH9, 3_CH4, -, -, -, - - D29, PB10, -, -, 2_SCL, 3_TX, -, Yes - D30, PB11, -, -, 2_SDA, 3_RX, -, Yes - D31, PB12, -, 1_BKIN, 2_SMBA, 3_CK, 2_NSS, Yes - D32, PB13, -, 1_CH1N, -, 3_CTS, 2_SCK, Yes - D33, PB14, -, 1_CH2N, -, 3_RTS, 2_MISO, Yes - D34, PB15, -, 1_CH3N, -, -, 2_MOSI, Yes - D35, PC6, -, 8_CH1, -, -, -, Yes - D36, PC7, -, 8_CH2, -, -, -, Yes - D37, PC8, -, 8_CH3, -, -, -, Yes - D38, PC9, -, 8_CH4, -, -, -, Yes - D39, PA13, -, -, -, -, -, Yes - D40, PA14, -, -, -, -, -, Yes - D41, PA15, -, -, -, -, 3_NSS, Yes - D42, PB3, -, -, -, -, 3_SCK, Yes - -.. _maple-ret6-gpio-port-map: - -GPIO Port Pin Map -^^^^^^^^^^^^^^^^^ - -The following table shows what pins are associated with each -:ref:`GPIO port `. - -.. csv-table:: - :header: GPIOA, GPIOB, GPIOC - - PA0: D2, PB0: D27, PC0: D15 - PA1: D3, PB1: D28, PC1: D16 - PA2: D1, PB2: -, PC2: D17 - PA3: D0, PB3: D42, PC3: D18 - PA4: D10, PB4: D43, PC4: D19 - PA5: D13, PB5: D4, PC5: D20 - PA6: D12, PB6: D5, PC6: D35 - PA7: D11, PB7: D9, PC7: D36 - PA8: D6, PB8: D14, PC8: D37 - PA9: D7, PB9: D24, PC9: D38 - PA10: D8, PB10: D29, PC10: D26 - PA11: -, PB11: D30, PC11: - - PA12: -, PB12: D31, PC12: - - PA13: D39, PB13: D32, PC13: D21 - PA14: D40, PB14: D33, PC14: D22 - PA15: D41, PB15: D34, PC15: D23 - -.. _maple-ret6-timer-map: - -Timer Pin Map -^^^^^^^^^^^^^ - -The following table shows what pins are associated with a particular -timer's capture/compare channels. Note that timer 5's channels share -pins with timer 2 (e.g., timer 5 channel 1 is also available on D2, -channel 2 on D3, etc.). - -.. csv-table:: - :header: Timer, Ch. 1, Ch. 2, Ch. 3, Ch. 4 - :delim: | - - 1 | D6 | D7 | D8 | - - 2 | D2 | D3 | D1 | D0 - 3 | D12 | D11 | D27 | D28 - 4 | D5 | D9 | D14 | D24 - 8 | D35 | D36 | D37 | :ref:`D38 ` - -.. _maple-ret6-exti-map: - -EXTI Line Pin Map -^^^^^^^^^^^^^^^^^ - -The following table shows which pins connect to which :ref:`EXTI lines -` on the Maple RET6 Edition. - -.. list-table:: - :widths: 1 1 - :header-rows: 1 - - * - EXTI Line - - Pins - * - EXTI0 - - D2, D15, D27 - * - EXTI1 - - D3, D16, D28 - * - EXTI2 - - D1, D17, D25 - * - EXTI3 - - D0, D18, D42 - * - EXTI4 - - D10, D19 - * - EXTI5 - - D4, D13, D20 - * - EXTI6 - - D5, D12, D35 - * - EXTI7 - - D9, D11, D36 - * - EXTI8 - - D6, D14, D37 - * - EXTI9 - - D7, D24, D38 - * - EXTI10 - - D8, D26, D29 - * - EXTI11 - - D30 - * - EXTI12 - - D31 - * - EXTI13 - - D21, D32, D39 - * - EXTI14 - - D22, D33, D40 - * - EXTI15 - - D23, D34, D41 - -.. _maple-ret6-usart-map: - -USART Pin Map -^^^^^^^^^^^^^ - -The Maple RET6 Edition has three serial ports whose pins are broken -out to headers (also known as :ref:`USARTs `). They communicate -using the pins given in the following table. - -.. csv-table:: - :header: Serial Port, TX, RX, CK, CTS, RTS - :delim: | - - ``Serial1`` | D7 | D8 | D6 | | - ``Serial2`` | D1 | D0 | D10 | D2 | D3 - ``Serial3`` | D29 | D30 | D31 | D32 | D33 - -Unfortunately, :ref:`UART4 and UART5 aren't completely available -`. - -.. _maple-ret6-adc-bank: - -Low-Noise ADC Pins -^^^^^^^^^^^^^^^^^^ - -The six pins at the bottom right of the board (D15—D20) generally -offer lower-noise ADC performance than other pins on the board. If -you’re concerned about getting good ADC readings, we recommend using -one of these pins to take your measurements. More details in the -:ref:`Maple hardware documentation `. - -Board-Specific Values ---------------------- - -This section lists the Maple RET6 Edition's :ref:`board-specific -values `. - -- ``CYCLES_PER_MICROSECOND``: 72 -- ``BOARD_BUTTON_PIN``: 38 -- ``BOARD_LED_PIN``: 13 -- ``BOARD_NR_GPIO_PINS``: 44 (however, :ref:`pin D43 is not usable - `) -- ``BOARD_NR_PWM_PINS``: 18 -- ``boardPWMPins``: 0, 1, 2, 3, 5, 6, 7, 8, 9, 11, 12, 14, 24, 27, 28, - 35, 36, 37 -- ``BOARD_NR_ADC_PINS``: 15 -- ``boardADCPins``: 0, 1, 2, 3, 10, 11, 12, 15, 16, 17, 18, 19, 20, 27, 28 -- ``BOARD_NR_USED_PINS``: 7 -- ``boardUsedPins``: ``BOARD_LED_PIN``, ``BOARD_BUTTON_PIN``, - ``BOARD_JTMS_SWDIO_PIN``, ``BOARD_JTCK_SWCLK_PIN``, - ``BOARD_JTDI_PIN``, ``BOARD_JTDO_PIN``, ``BOARD_NJTRST_PIN`` -- ``BOARD_NR_USARTS``: 3 (unfortunately, :ref:`due to the Maple Rev 5 - design `, UARTs 4 and 5 have pins which are not - broken out). -- ``BOARD_USART1_TX_PIN``: 7 -- ``BOARD_USART1_RX_PIN``: 8 -- ``BOARD_USART2_TX_PIN``: 1 -- ``BOARD_USART2_RX_PIN``: 0 -- ``BOARD_USART3_TX_PIN``: 29 -- ``BOARD_USART3_RX_PIN``: 30 -- ``BOARD_NR_SPI``: 2 (unfortunately, :ref:`due to the Maple Rev 5 - design `, SPI3 is unavailable). -- ``BOARD_SPI1_NSS_PIN``: 10 -- ``BOARD_SPI1_MOSI_PIN``: 11 -- ``BOARD_SPI1_MISO_PIN``: 12 -- ``BOARD_SPI1_SCK_PIN``: 13 -- ``BOARD_SPI2_NSS_PIN``: 31 -- ``BOARD_SPI2_MOSI_PIN``: 34 -- ``BOARD_SPI2_MISO_PIN``: 33 -- ``BOARD_SPI2_SCK_PIN``: 32 -- ``BOARD_JTMS_SWDIO_PIN``: 39 -- ``BOARD_JTCK_SWCLK_PIN``: 40 -- ``BOARD_JTDI_PIN``: 41 -- ``BOARD_JTDO_PIN``: 42 -- ``BOARD_NJTRST_PIN``: :ref:`43 ` - -.. _maple-ret6-hardware: - -Hardware Design Files ---------------------- - -The hardware schematics and board layout files are available in the -`Maple GitHub repository `_. Other -than the processor used, the design files for the Maple RET6 edition -are identical to the Maple Rev 5, which are in the ``maple-r5`` -subdirectory of the Maple repository. A schematic for a JTAG adapter -suitable for use with Maple is available in the ``jtagadapter`` -directory. - -From the GitHub repository main page, you can download the entire -repository by clicking the "Download" button. If you are familiar -with `Git `_, you can also clone the repository -at the command line with :: - - $ git clone git://github.com/leaflabs/maple.git - -.. _maple-ret6-failure-modes: - -Failure Modes -------------- - -The following known failure modes apply to all Maple boards. The -failure modes aren't design errors, but are easy ways to break or -damage your board permanently. - -* **High voltage on non-tolerant pins**: not all header pins are 5V - compatible; so e.g. connecting certain serial devices in the wrong - way could over-voltage the pins. The :ref:`pin-mapping master table - ` details which pins are - :ref:`5V-tolerant `. - -Errata ------- - -This section lists known issues and warnings for the Maple RET6 -Edition. Some of these are simply due to the RET6 Edition using the -Maple's circuit board, which was not designed to accomodate extra -features only available on the STM32F103RET6. - -.. _maple-ret6-barrel-jack: - -* **Barrel jack power supply voltage mistake**: The acceptable voltage - range given next to the barrel jack on the Maple RET6 is - **incorrect**. The given range is 7V — 18V. In fact, **18V is too - high** and should not be supplied to your board. The original - voltage regulators used on the Maple were rated up to 18V. However, - the voltage regulators on current Maple Revs are rated up to only - 16V, and due to the current draw requirements of the board, operate - properly only up to 12V. The recommended maximum voltage you should - apply is **12V**, and potentially even lower depending upon the - current draw requirements of the application. Please see :ref:`Power - Regulation on the Maple ` for more - information. - -* **Power supply marketing mistake**: We originally sold the Maple - RET6 Edition advertising that it was capable of supplying up to 800 - mA; the correct value is 500 mA. - -.. _maple-ret6-uarts: - -* **UART4, UART5 GPIOs unavailable**: Pins related to UARTs 4 and 5 - are not broken out to headers (specifically, PC11/UART4_RX and - PC12/UART5_TX). This is due to the RET6 Edition's board layout - being that of the Maple Rev 5, which was not designed with these - RET6-specific features in mind. - -.. _maple-ret6-dac-ch2: - -* **DAC channel 2 on BOARD_LED_PIN**: The Maple Rev 5 connects PA5 to - the board's built-in LED; this is the same GPIO bit which is - connected to the DAC's channel 2 output. This is also due to the - RET6 Edition's board layout being that of the Maple Rev 5. The DAC - output channel is still available, and (if you use the - :ref:`standard libmaple DAC interface `) its output is - buffered by default, so this may not significantly interfere with - its functionality. - -.. _maple-ret6-nrst-pb4: - -* **Reset and PB4 tied together**: The RET6 Edition's reset line is - also connected to PB4, which is labeled on the silkscreen as pin 43. - Thus, attempting to use pin 43 as a GPIO can reset your board. This - has other implications. Since PB4 is also the JTAG NJTRST line, - this prevents the :ref:`JTAG ` "reset halt" command from - working properly. Also, since PB4 is SPI3_MISO, the SPI3 peripheral - is not fully usable. - -.. _maple-ret6-sdio: - -* **SDIO lines not broken out**: The RET6 Edition's SDIO peripheral is - not usable, as some of its data lines are either not broken out or - used for other purposes. This is also due to the RET6 Edition's - board layout being that of the Maple Rev 5. - -.. _maple-ret6-adc-led: - -* **ADC on BOARD_LED_PIN**: We originally sold the Maple RET6 Edition - advertising 16 analog input lines. However, one of them (the one on - pin 13) is also connected to the built-in LED. The voltage drop - across the LED means that the analog to digital converter on that - pin is not really useful. While it is still usable, its readings - will be incorrect. - -Recommended Reading -------------------- - -.. _maple-ret6-stdocs: - -STMicro documentation for STM32F103RE microcontroller: - -* `Datasheet - `_ - (PDF); covers STM32F103xC, STM32F103xD, STM32F103xE. -* `Reference Manual RM0008 - `_ - (PDF); definitive resource for peripherals on the STM32F1 line. -* `Programming Manual PM0056 - `_ - (PDF); assembly language and register reference. -* `STM32F103RE `_ - overview page with links to further references. diff --git a/docs/source/hardware/maple.rst b/docs/source/hardware/maple.rst deleted file mode 100644 index b187115..0000000 --- a/docs/source/hardware/maple.rst +++ /dev/null @@ -1,618 +0,0 @@ -.. highlight:: sh - -.. _maple: - -Maple -===== - -This page is a general resource for information specific to the Maple. - -.. contents:: Contents - :local: - -.. TODO [dma.rst] Ref to dma.rst in sequel instead of libmaple-dma -.. TODO [nvic.rst] Ref to nvic.rst in sequel - -Technical Specifications ------------------------- - -* MCU: :ref:`STM32F103RBT6 `, a 32-bit ARM Cortex M3 - microprocessor -* Clock Speed: **72 MHz** -* **128 KB Flash** and **20 KB SRAM** -* 43 :ref:`digital I/O pins (GPIOs) ` -* 15 :ref:`PWM ` pins at 16 bit resolution -* 15 :ref:`analog input (ADC) ` pins at 12-bit resolution -* 2 :ref:`SPI ` peripherals -* 2 :ref:`I2C ` peripherals -* 7 Channels of Direct Memory Access (**DMA**) (:ref:`libmaple-dma`) -* 3 :ref:`USART (serial port) ` peripherals -* One advanced and three general-purpose :ref:`timers ` -* Dedicated :ref:`USB ` port for programming and communications -* :ref:`JTAG ` -* Nested Vectored Interrupt Controller (NVIC) (including - :ref:`external interrupt ` on GPIOs) -* Supplies up to 500 mA at 3.3 V, with separate 250 mA digital and - analog regulators for low-noise analog performance -* :ref:`Open source, four layer design ` -* Support for low power, sleep, and standby modes (<500 μA) -* Operating Voltage: 3.3 V -* Input Voltage (recommended): 4 V — 12 V -* Dimensions: 2.05″ × 2.1″ - -.. _maple-identify-rev: - -Identifying your Rev --------------------- - -We went through three versions ("Revs") of the Maple hardware: Rev 1, -Rev 3, and Rev 5 [#frev2_4]_; Rev 5, the final design, is currently on -sale. The following sections will help you to help you identify your -Rev. - -Rev 5 -^^^^^ - -These boards went on sale in November 2010. They have white buttons -and "r5" in small print near the "LeafLabs Maple" text next to the -"infinity leaf" logo. The Maple Rev 5 repositioned the double header -on the right hand side to better fit 0.1 inch pitch breadboard. This -necessitated the removal of pins 21 and 22 from the double header; -they are still available, but don't have any headers installed on -them. - -.. figure:: /_static/img/maple_rev5.png - :align: center - :alt: Maple Rev 5 - -Rev 3 -^^^^^ - -This batch of boards went on sale beginning in May 2010. They have a -darker red silkscreen and the "infinity leaf" logo. The Maple Rev 3 -was the first version which includes the built-in button, labeled BUT. - -.. figure:: /_static/img/maple_rev3.png - :align: center - :alt: Maple Rev 3 - -Rev 1 -^^^^^ - -A small number of Maple Rev 1 boards went on sale in late 2009. They -have a light red silkscreen and a single pixelated leaf as a logo. - -.. figure:: /_static/img/maple_rev1.png - :align: center - :alt: Maple Rev 1 - -.. _maple-powering: - -Powering the Maple ------------------- - -The Maple's power source is determined by the header to the left of -the "LeafLabs" label on the silkscreen. All versions of the Maple can -be powered from the barrel jack connector, USB, or a LiPo battery. We -ship the Maple with a jumper on the USB selector. In order to power -it off of an alternative source, unplug the Maple, then move the -jumper to the desired selector before reconnecting power. - -You can also power the Maple via the pin labeled "Vin" on the lower -header. This pin feeds into both the digital and analog voltage -regulators. However, don't do this while simultaneously powering the -board from another source, or you could damage it. - -When powering the board from a barrel jack, **double check the -polarity of the barrel.** The appropriate polarity is noted on the -silkscreen right next to the connector. - -.. warning:: Silkscreens on Maples up through Rev 5s manufactured in - Spring 2011 falsely indicated that the barrel jack could be - supplied by up to 18V. (Rev5s manufactured after Spring 2011 may - still have this error on the silk, but it has been marked over.) We - recommend a barrel jack input voltage **no greater than 12V**, and - potentially even lower depending upon the current draw requirements - of the application. The same goes for powering off LiPo batteries. - - Please see :ref:`Power Regulation on the Maple - ` for more information. - -.. _maple-power-regulation: - -Power Regulation on the Maple ------------------------------ - -Power regulation on the Maple is provided by two low dropout linear -voltage regulators. (The part is the MCP1703 from Microchip, in the -SOT-23A package. You can download the datasheet `here -`_ ). One -of the regulators supplies power to the digital voltage plane; the -other supplies power to the analog voltage plane. - -These voltage regulators nominally take an input of up to 16V. In -addition, while the maximum continuous output current for the board is -250mA, if you are powering the board off higher voltages the current -it can supply goes down, due to the regulators needing to dissipate -the extra power. So if you are powering the board off 12V, the max -current is about 40mA at room temperature. In general (again, at room -temperature) the max power dissipation (PD) for the chip is about -.37W, and output current = PD/(Vin-Vout). For exact max current -calculations, please refer to the datasheet linked above. - -If you are planning to draw a lot of current from the Maple board, it -is necessary to provide input power as close to 3.3V as -possible. Powering the microcontroller circuitry and LEDs on the board -alone takes approximately 30mA, so if you are powering the board with -12V that leaves only 10mA (at best) available for powering any user -circuitry. Attempting to draw more than 10mA runs the risk of shorting -out the power regulators and bricking your board. - -Using the Built-in Battery Charger ----------------------------------- - -Maples Rev 3 and Rev 5 also have a built-in LiPo battery charger. In -order to use it, put a jumper across the CHRG header on the power -selection header and across the USB, or EXT selectors, depending on -whether you're charging the battery via USB cable or barrel jack -connector. The LED labeled CHRG will light up while the battery is -being charged. When the battery is finished charging, the LED labeled -DONE will light up. - -.. _maple-gpios: - -GPIO Information ----------------- - -The Maple features 38 ready-to-use general purpose input/output (see -:ref:`gpio`) pins for digital input/output, numbered ``D0`` through -``D37``. These numbers correspond to the numeric values next to each -header on the Maple silkscreen. - -.. _maple-ret6-but: - -Pin ``D38`` is the board's :ref:`button pin `. -It is thus mainly useful as an :ref:`input `. The -pin will :ref:`read ` ``HIGH`` when the :ref:`button -is pressed `. - -More GPIOs (numbered ``D39``\ --``D42`` on the back of the Maple's -silkscreen) are available if you use the :ref:`lang-disabledebugports` -function; see the :ref:`board-specific debug pin constants -` for more information. (See :ref:`this -erratum ` for information about the pin numbered -``43`` on the silkscreen). - -.. TODO [0.1.0] silkscreen pictures which expand abbreviations - -.. _maple-pin-map-master: - -Master Pin Map -^^^^^^^^^^^^^^ - -This table shows a summary of the available functionality on every -GPIO pin, by peripheral type. The "5 V?" column documents whether or -not the pin is :ref:`5 volt tolerant `. - -Note that this table is not exhaustive; on some pins, more peripherals -are available than are listed here. - -.. csv-table:: - :header: Pin, :ref:`GPIO `, :ref:`ADC `, :ref:`Timer `, :ref:`I2C `, :ref:`UART `, :ref:`SPI `, 5 V? - - D0, PA3, CH3, 2_CH4, -, 2_RX, -, - - D1, PA2, CH2, 2_CH3, -, 2_TX, -, - - D2, PA0, CH0, 2_CH1_ETR, -, 2_CTS, -, - - D3, PA1, CH1, 2_CH2, -, 2_RTS, -, - - D4, PB5, -, -, 1_SMBA, -, -, - - D5, PB6, -, 4_CH1, 1_SCL, -, -, Yes - D6, PA8, -, 1_CH1, -, 1_CK, -, Yes - D7, PA9, -, 1_CH2, -, 1_TX, -, Yes - D8, PA10, -, 1_CH3, -, 1_RX, -, Yes - D9, PB7, -, 4_CH2, 1_SDA, -, -, Yes - D10, PA4, CH4, -, -, 2_CK, 1_NSS, - - D11, PA7, CH7, 3_CH2, -, -, 1_MOSI, - - D12, PA6, CH6, 3_CH1, -, -, 1_MISO, - - D13, PA5, CH5, -, -, -, 1_SCK, - - D14, PB8, -, 4_CH3, -, -, -, Yes - D15, PC0, CH10, -, -, -, -, - - D16, PC1, CH11, -, -, -, -, - - D17, PC2, CH12, -, -, -, -, - - D18, PC3, CH13, -, -, -, -, - - D19, PC4, CH14, -, -, -, -, - - D20, PC5, CH15, -, -, -, -, - - D21, PC13, -, -, -, -, -, - - D22, PC14, -, -, -, -, -, - - D23, PC15, -, -, -, -, -, - - D24, PB9, -, 4_CH4, -, -, -, Yes - D25, PD2, -, 3_ETR, -, -, -, Yes - D26, PC10, -, -, -, -, -, Yes - D27, PB0, CH8, 3_CH3, -, -, -, - - D28, PB1, CH9, 3_CH4, -, -, -, - - D29, PB10, -, -, 2_SCL, 3_TX, -, Yes - D30, PB11, -, -, 2_SDA, 3_RX, -, Yes - D31, PB12, -, -, 2_SMBA, 3_CK, 2_NSS, Yes - D32, PB13, -, -, -, 3_CTS, 2_SCK, Yes - D33, PB14, -, -, -, 3_RTS, 2_MISO, Yes - D34, PB15, -, -, -, -, 2_MOSI, Yes - D35, PC6, -, -, -, -, -, Yes - D36, PC7, -, -, -, -, -, Yes - D37, PC8, -, -, -, -, -, Yes - D38, PC9, -, -, -, -, -, Yes - D39, PA13, -, -, -, -, -, Yes - D40, PA14, -, -, -, -, -, Yes - D41, PA15, -, -, -, -, -, Yes - D42, PB3, -, -, -, -, -, Yes - -.. _maple-gpio-port-map: - -GPIO Port Pin Map -^^^^^^^^^^^^^^^^^ - -The following table shows what pins are associated with each -:ref:`GPIO port `. - -.. csv-table:: - :header: GPIOA, GPIOB, GPIOC - - PA0: D2, PB0: D27, PC0: D15 - PA1: D3, PB1: D28, PC1: D16 - PA2: D1, PB2: -, PC2: D17 - PA3: D0, PB3: D42, PC3: D18 - PA4: D10, PB4: D43, PC4: D19 - PA5: D13, PB5: D4, PC5: D20 - PA6: D12, PB6: D5, PC6: D35 - PA7: D11, PB7: D9, PC7: D36 - PA8: D6, PB8: D14, PC8: D37 - PA9: D7, PB9: D24, PC9: D38 - PA10: D8, PB10: D29, PC10: D26 - PA11: -, PB11: D30, PC11: - - PA12: -, PB12: D31, PC12: - - PA13: D39, PB13: D32, PC13: D21 - PA14: D40, PB14: D33, PC14: D22 - PA15: D41, PB15: D34, PC15: D23 - -.. _maple-timer-map: - -Timer Pin Map -^^^^^^^^^^^^^ - -The following table shows what pins are associated with a particular -timer's capture/compare channels. - -.. csv-table:: - :header: Timer, Ch. 1, Ch. 2, Ch. 3, Ch. 4 - :delim: | - - 1 | D6 | D7 | D8 | - - 2 | D2 | D3 | D1 | D0 - 3 | D12 | D11 | D27 | D28 - 4 | D5 | D9 | D14 | D24 - -.. _maple-exti-map: - -EXTI Line Pin Map -^^^^^^^^^^^^^^^^^ - -The following table shows which pins connect to which :ref:`EXTI lines -` on the Maple. - -.. list-table:: - :widths: 1 1 - :header-rows: 1 - - * - EXTI Line - - Pins - * - EXTI0 - - D2, D15, D27 - * - EXTI1 - - D3, D16, D28 - * - EXTI2 - - D1, D17, D25 - * - EXTI3 - - D0, D18, D42 - * - EXTI4 - - D10, D19 - * - EXTI5 - - D4, D13, D20 - * - EXTI6 - - D5, D12, D35 - * - EXTI7 - - D9, D11, D36 - * - EXTI8 - - D6, D14, D37 - * - EXTI9 - - D7, D24, D38 - * - EXTI10 - - D8, D26, D29 - * - EXTI11 - - D30 - * - EXTI12 - - D31 - * - EXTI13 - - D21, D32, D39 - * - EXTI14 - - D22, D33, D40 - * - EXTI15 - - D23, D34, D41 - -.. _maple-usart-map: - -USART Pin Map -^^^^^^^^^^^^^ - -The Maple has three serial ports (also known as :ref:`USARTs -`): ``Serial1``, ``Serial2``, and ``Serial3``. They communicate -using the pins given in the following table. - -.. csv-table:: - :header: Serial Port, TX, RX, CK, CTS, RTS - :delim: | - - ``Serial1`` | D7 | D8 | D6 | | - ``Serial2`` | D1 | D0 | D10 | D2 | D3 - ``Serial3`` | D29 | D30 | D31 | D32 | D33 - -.. _maple-adc-bank: - -Low-Noise ADC Pins -^^^^^^^^^^^^^^^^^^ - -The six pins at the bottom right of the board (D15—D20) generally -offer lower-noise ADC performance than other pins on the board. If -you’re concerned about getting good ADC readings, we recommend using -one of these pins to take your measurements. - -Maple has an electrically isolated analog power plane with its own -regulator, and a geometrically isolated ground plane. Pins D15—D20 are -laid out to correspond with these analog planes, and our measurements -indicate that they generally have the lowest noise of all the analog -lines. However, analog performance may vary depending upon the -activity of the other GPIOs. Consult the :ref:`Maple hardware design -files ` for more details. - -Board-Specific Values ---------------------- - -This section lists the Maple's :ref:`board-specific values -`. - -- ``CYCLES_PER_MICROSECOND``: 72 -- ``BOARD_BUTTON_PIN``: 38 -- ``BOARD_LED_PIN``: 13 -- ``BOARD_NR_GPIO_PINS``: 44 (however, :ref:`pin D43 is not usable - `) -- ``BOARD_NR_PWM_PINS``: 15 -- ``boardPWMPins``: 0, 1, 2, 3, 5, 6, 7, 8, 9, 11, 12, 14, 24, 27, 28 -- ``BOARD_NR_ADC_PINS``: 15 -- ``boardADCPins``: 0, 1, 2, 3, 10, 11, 12, 15, 16, 17, 18, 19, 20, 27, 28 -- ``BOARD_NR_USED_PINS``: 7 -- ``boardUsedPins``: ``BOARD_LED_PIN``, ``BOARD_BUTTON_PIN``, - ``BOARD_JTMS_SWDIO_PIN``, ``BOARD_JTCK_SWCLK_PIN``, - ``BOARD_JTDI_PIN``, ``BOARD_JTDO_PIN``, ``BOARD_NJTRST_PIN`` -- ``BOARD_NR_USARTS``: 3 -- ``BOARD_USART1_TX_PIN``: 7 -- ``BOARD_USART1_RX_PIN``: 8 -- ``BOARD_USART2_TX_PIN``: 1 -- ``BOARD_USART2_RX_PIN``: 0 -- ``BOARD_USART3_TX_PIN``: 29 -- ``BOARD_USART3_RX_PIN``: 30 -- ``BOARD_NR_SPI``: 2 -- ``BOARD_SPI1_NSS_PIN``: 10 -- ``BOARD_SPI1_MOSI_PIN``: 11 -- ``BOARD_SPI1_MISO_PIN``: 12 -- ``BOARD_SPI1_SCK_PIN``: 13 -- ``BOARD_SPI2_NSS_PIN``: 31 -- ``BOARD_SPI2_MOSI_PIN``: 34 -- ``BOARD_SPI2_MISO_PIN``: 33 -- ``BOARD_SPI2_SCK_PIN``: 32 -- ``BOARD_JTMS_SWDIO_PIN``: 39 -- ``BOARD_JTCK_SWCLK_PIN``: 40 -- ``BOARD_JTDI_PIN``: 41 -- ``BOARD_JTDO_PIN``: 42 -- ``BOARD_NJTRST_PIN``: :ref:`43 ` - -.. _maple-hardware: - -Hardware Design Files ---------------------- - -The hardware schematics and board layout files are available in the -`Maple GitHub repository `_. The -design files for Rev 1, Rev 3, and Rev 5 are respectively in the -``maple-r1``, ``maple-r3``, and ``maple-r5`` subdirectories. A -schematic for a JTAG adapter suitable for use with Maple is available -in the ``jtagadapter`` directory. - -From the GitHub repository main page, you can download the entire -repository by clicking the "Download" button. If you are familiar -with `Git `_, you can also clone the repository -at the command line with :: - - $ git clone git://github.com/leaflabs/maple.git - -.. _maple-failure-modes: - -Failure Modes -------------- - -The following are known failure modes. The failure modes aren't -design errors, but are easy ways to break or damage your board -permanently. - -* **High voltage on non-tolerant pins**: not all header pins are 5V - compatible; so e.g. connecting certain serial devices in the wrong - way could over-voltage the pins. The :ref:`pin-mapping master table - ` details which pins are :ref:`5 V tolerant - `. - -Errata ------- - -This section documents design flaws and other errors. - -General -^^^^^^^ - -.. _maple-barrel-jack: - -* **Barrel jack power supply voltage mistake**: The acceptable voltage - range given next to the barrel jack on the Maple through Rev 5s - manufactured in Spring 2011 is **incorrect**. The given range is 7V - — 18V. In fact, **18V is too high** and should not be supplied to - your board. The original voltage regulators used on the Maple were - rated up to 18V. However, the voltage regulators on current Maple - Revs are rated up to only 16V, and due to the current draw - requirements of the board, operate properly only up to 12V. The - recommended maximum voltage you should apply is **12V**, and - potentially even lower depending upon the current draw requirements - of the application. Please see :ref:`Power Regulation on the Maple - ` for more information. - -.. _maple-nrst-pb4: - -* **Reset and PB4 tied together**: The Maple's reset line is also - connected to PB4, which is labeled on the silkscreen as pin 43. - Thus, attempting to use pin 43 as a GPIO can reset your board. This - has other implications. Since PB4 is also the JTAG NJTRST line, - this prevents the :ref:`JTAG ` "reset halt" command from - working properly. - -.. _maple-power-supply: - -* **Power supply marketing mistake**: We originally sold the Maple - advertising that it was capable of supplying up to 800 mA; the - correct value is 500 mA. - -.. _maple-pwm-marketing: - -* **PWM marketing mistake**: We originally advertised the Maple as - having 22 PWM-capable pins; the correct number is 15. - -.. _maple-adc-marketing: - -* **ADC marketing mistake**: We originally advertised the Maple as - having 16 analog input pins. Due to :ref:`the following issue - `, the correct number is 15. - -.. _maple-adc-led: - -* **ADC on BOARD_LED_PIN**: We originally sold the Maple RET6 Edition - advertising 16 analog input lines. However, one of them (the one on - pin 13) is also connected to the built-in LED. The voltage drop - across the LED means that the analog to digital converter on that - pin is not really useful. While it is still usable, its readings - will be incorrect. - - -By Rev -^^^^^^ - -The following subsections lists known issues and warnings for each -revision of the Maple board. - -Rev 5 -~~~~~ - -* **Pin 3 AIN missing**: Pin 3 is capable of analog input, but on Rev - 5s manufactured during Fall 2010, the corresponding "AIN" is missing - from its silkscreen. This mistake was fixed in later manufacturing - runs. - -Rev 3 -~~~~~ - -* **Pin 3 AIN missing**: Pin 3 is capable of analog input, but the - corresponding "AIN" is missing from the Rev 3 silkscreen. - -.. _maple-rev3-bad-buttons: - -* **Bad/Sticky Buttons**: a number of Rev 3 boards sold in May-June 2010 - have questionable RESET and BUT buttons. - - What seems to have happened is that the flux remover we used to - clean the boards before shipping eroded the plastic internals, which - resulted in intermittent functionality. All buttons on all shipped - boards did function in testing, but some may have been unreliable in - regular use. - - If you have this problem, we will be happy to ship you new buttons - if you think you can re-solder them yourself, or you can ship us - your board and we will swap out that part. - - For reference, the button part number is KMR211GLFS and the flux - remover we used is "Precision Electronics Cleaner" from RadioShack, - which is "Safe on most plastics" and contains: dipropylene glycol - monomethyl ether, hydrotreated heavy naphtha, dipropylene glycol - methyl ether acetate (say that three times fast!), and carbon - dioxide. - -* **Resistors on pins 0 and 1**: these header pins, which are RX/TX on - USART2 (:ref:`Serial2 `), have resistors in-line - between the STM32 and the headers. These resistors increase the - impedance of the lines for ADC reads and affect the open drain GPIO - functionality of the pins. - - These resistors were accidentally copied over from older Arduino USB - designs, where they appear to protect the USB-Serial converter from - TTL voltage on the headers. - -* **Silkscreen Errors**: the silkscreen on the bottom indicated PWM - functionality on pin 25 and listen the external header GND pin as - number 38 (actually 38 is connected to the BUT button). We manually - sharpied over both of these mistakes. - -Rev 1 -~~~~~ - -* **ADC noise**: generally very high, in particular when the USB port - is being used for communications (including keep-alive pings when - connected to a computer). - - This issue was resolved in Rev 3 with a 4-layer design and a - :ref:`geometrically isolated ADC Vref plane `. - -* **Resistors on pins 0 and 1**: these header pins, which are RX/TX on - USART2 (:ref:`Serial2 `), have resistors in-line - between the STM32 and the headers. These resistors increase the - impedance of the lines for ADC reads and affect the open drain GPIO - functionality of the pins. - - These resistors were accidentally copied over from older Arduino USB - designs, where they appear to protect the USB-Serial converter from - TTL voltage on the headers. - -* **Silkscreen Differences**: the pin numbering scheme on Rev 1 is - different from Rev 3, and thus Rev 3 software is difficult to use - with Rev 1 boards. Notably, the analog input bank is labeled A0-A4 - on Rev 1 but 15-20 on Rev 3, and the extra header bank does not have - a pinout table on the bottom. - -* **No BUT Button**: the BUT button, useful for serial bootloading, - was only added in Rev 3. As a workaround, you can directly short the - appropriate MCU pin to Vcc; see `this forum posting - `_. - -Recommended Reading -------------------- - -.. _maple-stdocs: - -STMicro documentation for STM32F103RB microcontroller: - -* `Datasheet - `_ - (PDF); covers STM32F103x8, STM32F103xB. -* `Reference Manual RM0008 - `_ - (PDF); definitive resource for peripherals on the STM32F1 line. -* `Programming Manual PM0056 - `_ - (PDF); assembly language and register reference. -* `STM32F103RB `_ - overview page with links to further references. - -.. rubric:: Footnotes - -.. [#frev2_4] Revs 2 and 4 were prototypes that didn't pass internal - testing. diff --git a/docs/source/lang/api/analogread.rst b/docs/source/lang/api/analogread.rst index 6665a94..59eab79 100644 --- a/docs/source/lang/api/analogread.rst +++ b/docs/source/lang/api/analogread.rst @@ -40,9 +40,8 @@ listed underneath their number on your board's silkscreen. These pin numbers are available to your program in the :ref:`boardADCPins ` board-specific array. The number of pins which are capable of analog to digital conversion on your board -is given by the ``BOARD_NR_ADC_PINS`` constant. These values are -documented for each board in the :ref:`Board Hardware Documentation -` pages. +is given by the ``BOARD_NR_ADC_PINS`` constant. See your board's +documentation for these values. .. note:: Pin 3 is not marked ``AIN`` on the silkscreen for Maple revisions through Rev 5; however **it does work** as an analog diff --git a/docs/source/lang/api/board-values.rst b/docs/source/lang/api/board-values.rst index d944c8d..70eff60 100644 --- a/docs/source/lang/api/board-values.rst +++ b/docs/source/lang/api/board-values.rst @@ -7,8 +7,8 @@ Board-Specific Values There are a number of board-specific values: constants or variables which are different depending on which LeafLabs board you have. The -exact values for each board are given in your :ref:`board's hardware -documentation `. +exact values for each board are given in your board's hardware +documentation. This page lists and documents the board-specific values. You should use these when appropriate in your own programs. This will help make @@ -122,8 +122,8 @@ Constants `). However, they can be used as ordinary GPIOs if you call the :ref:`lang-disabledebugports` function. (Be careful with this on the Maple and Maple RET6 - Edition, as writing to ``BOARD_NJTRST_PIN`` :ref:`may cause your - board to reset `\ !). + Edition, as writing to ``BOARD_NJTRST_PIN`` may cause your + board to reset!). .. _lang-board-values-pwm-pins: diff --git a/docs/source/lang/api/disabledebugports.rst b/docs/source/lang/api/disabledebugports.rst index 283cdbf..071d4c3 100644 --- a/docs/source/lang/api/disabledebugports.rst +++ b/docs/source/lang/api/disabledebugports.rst @@ -30,4 +30,6 @@ See Also -------- - :ref:`lang-enabledebugports` -- :ref:`Important erratum on Maple pin 43 ` +- Important erratum on Maple pin 43 + +.. TODO direct off-site link to diff --git a/docs/source/lang/api/pwmwrite.rst b/docs/source/lang/api/pwmwrite.rst index 5cc112e..aa39ab1 100644 --- a/docs/source/lang/api/pwmwrite.rst +++ b/docs/source/lang/api/pwmwrite.rst @@ -15,9 +15,8 @@ The pins which support PWM have ``PWM`` listed underneath their number on your board's silkscreen. These pin numbers are available to your program in the :ref:`boardPWMPins ` board-specific array. The number of pins which are capable of PWM on -your board is given by the ``BOARD_NR_PWM_PINS`` constant. These -values are documented for each board in the :ref:`Board Hardware -Documentation ` pages. +your board is given by the ``BOARD_NR_PWM_PINS`` constant. See your +board's documentation for these values. The Arduino function :ref:`analogWrite() ` is an alias for ``pwmWrite()``, but it is badly named, and its use is diff --git a/docs/source/language.rst b/docs/source/language.rst index a24bb5f..d145334 100644 --- a/docs/source/language.rst +++ b/docs/source/language.rst @@ -420,8 +420,8 @@ Which could plausibly be turned into the final source file :: Recommended Reading ------------------- -* :ref:`Your board's documentation ` page, which - includes references to the relevant ST materials (reference manual, +* Your board's documentation, which should include + references to the relevant ST materials (reference manual, datashseet, etc.) for your board. * `ARM Cortex-M3 Technical Reference Manual, Revision r1p1 `_ (PDF). This ARM manual specifies the Cortex-M3 architecture, diff --git a/docs/source/libs/servo.rst b/docs/source/libs/servo.rst index 549e86f..cc2dac7 100644 --- a/docs/source/libs/servo.rst +++ b/docs/source/libs/servo.rst @@ -53,7 +53,7 @@ to attach to pins that support PWM**. To determine if a pin supports PWM, you can either check if "PWM" appears next to its number on your board's silkscreen, or look for it in the list of :ref:`boardPWMPins ` in -your board's :ref:`hardware documentation `. +your board's hardware documentation. RC Servos expect a pulse approximately every 20ms. In the Maple implementation, :ref:`periods ` are set diff --git a/docs/source/timers.rst b/docs/source/timers.rst index 0fa0976..a7281f2 100644 --- a/docs/source/timers.rst +++ b/docs/source/timers.rst @@ -82,10 +82,10 @@ you want to use both timer interrupts and PWM in the same program. Refer to your board's timer pin map to match up timer channels and pin numbers: -* :ref:`Maple ` -* :ref:`Maple RET6 Edition ` -* :ref:`Maple Mini ` -* :ref:`Maple Native Beta ` +* `Leaflabs Maple`_ +* `Leaflabs Maple RET6`_ +* `Leaflabs Maple Mini`_ +* `Leaflabs Maple Native Beta`_ Overhead ^^^^^^^^ diff --git a/docs/source/troubleshooting.rst b/docs/source/troubleshooting.rst index 181c3d4..0e9e13d 100644 --- a/docs/source/troubleshooting.rst +++ b/docs/source/troubleshooting.rst @@ -10,68 +10,6 @@ This page documents common problems and their solutions. .. contents:: Contents :local: -=================== - Hardware problems -=================== - -.. _troubleshooting-throb: - -The LED is throbbing and my program is stopped! ------------------------------------------------ - -The LED throbs when there has been a failed software :ref:`ASSERT() -` or some other error. - -In the case of a failed assertion, a first debugging step you can take -is to find out the file and line where the failed assertion took place -(for instructions on this, see the ``ASSERT()`` documentation linked -to above). This may give you some clue about the source of the error. - -:ref:`libmaple` often uses ``ASSERT()`` to halt immediately when it -detects that something has gone wrong, so if you're not using -assertions, then what's probably happening is that some bug is causing -the failed ``ASSERT()`` lower down. - -If it's not a failed assertion, then you're likely looking at -something like a `hard fault -`_. - -There are a few issues with the bootloader which mean you might not be -able to upload your program when this happens. You can still -reprogram by using :ref:`perpetual bootloader mode -`. - -My board is bricked! I can't upload via the bootloader no matter what! ----------------------------------------------------------------------- - -Don't panic. First, make sure that the board is plugged in correctly -for program upload. If that doesn't work, -try using :ref:`perpetual bootloader mode -`. - -If that doesn't work, then you've got a problem. All is not lost, -however! You can always try to :ref:`re-flash the bootloader -` over serial (or :ref:`JTAG `). - -If your board really is bricked, and you think it's our fault, -`contact us `_\ ! - -My 5v peripheral doesn't work! (I2C, SPI, USART, etc) ------------------------------------------------------ - -Yup, the Maple is a 3.3v board. You may need to use a level -converter. See the :ref:`Arduino Compatibility -`, :ref:`GPIO `, or other :ref:`hardware -specific documentation ` for more information. - -The reset and D38/serial buttons don't seem to work reliably! -------------------------------------------------------------- - -A few Maple Rev3 boards shipped in May-June 2010 may have had -unreliable buttons; see the :ref:`Maple Errata -` for details. `We're happy to replace these -for you `_\ ! - .. _troubleshooting-ide-install: ======================= diff --git a/docs/source/usart.rst b/docs/source/usart.rst index dbbc81c..7fb8db7 100644 --- a/docs/source/usart.rst +++ b/docs/source/usart.rst @@ -31,10 +31,10 @@ Which pins correspond to the USART TX and RX pins are given on your board's silkscreen, and also in the board-specific USART pin maps available here: -* :ref:`Maple ` -* :ref:`Maple RET6 Edition ` -* :ref:`Maple Mini ` -* :ref:`Maple Native Beta ` +* `Leaflabs Maple`_ +* `Leaflabs Maple RET6`_ +* `Leaflabs Maple Mini`_ +* `Leaflabs Maple Native Beta`_ If you use a particular serial port, you cannot also use its communication pins for other purposes at the same time. -- cgit v1.2.3