From fb674494256d51cee09a3ce2c0ead3ac4dd86a46 Mon Sep 17 00:00:00 2001 From: Marti Bolivar Date: Thu, 7 Oct 2010 20:12:29 -0400 Subject: lots more docs --- docs/source/libraries.rst | 114 +++++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 113 insertions(+), 1 deletion(-) (limited to 'docs/source/libraries.rst') diff --git a/docs/source/libraries.rst b/docs/source/libraries.rst index 374b71c..1f298fa 100644 --- a/docs/source/libraries.rst +++ b/docs/source/libraries.rst @@ -1,7 +1,119 @@ +.. highlight:: c++ +.. default-domain:: cpp + .. _libraries: ========================= Maple Library Reference ========================= -Stub +This page briefly summarizes the Arduino libraries that have been ported to Maple. You can use a library from within a sketch by going to Sketch > Import Library... from within the IDE, then choosing the library you want. + +Any incompatibilities between the Maple and Arduino versions are noted in the description of the library. + +* :ref:`LiquidCrystal ` +* :ref:`Wire ` + +.. _liquid_crystal: + +LiquidCrystal +------------- + +The LiquidCrystal library allows Maple to control LCD screens. For more information, see the Arduino LiquidCrystal documentation. +Compatibility Note + +At this time, no incompatibilities between the Maple and Arduino versions are known. Any observed differences should be considered bugs, and reported on the forums. + +.. _wire: + +Wire +---- + +We provide a soft (bit-banged) implementation of the `Wire I2C library +`_. + +Compatibility Note +^^^^^^^^^^^^^^^^^^ + +This implementation is synchronous, and thus supports only a subset of +the full Wire interface (however, the functionality which is supported +is fully compatible with Arduino). For now, please use the function +reference which follows when developing projects using our +implementation. + +Please note that the current implementation only supports master mode +using a bit-banged (software) protocol. Future enhancements will use +the hardware i2c peripheral on the stm32 as well as the DMA for +performance. Support for slave, smBUS, and multimaster modes are also +slated for inclusion in the enhanced Wire port. + +Function Reference +^^^^^^^^^^^^^^^^^^ + +``Wire.begin()`` + Joins the i2c bus as master, using pin 20 as SDA and pin 21 as SCL + (this is compatible with the pin settings on the Arduino Mega). + +``Wire.begin(sda, scl)`` + Like ``Wire.begin()``, but with the given pins as SDA and + SCL. + +``Wire.beginTransmission(slave_address)`` + Set up a transmission to a slave device with the given (7-bit) + address. Bytes subsequently queued for transmission (using + ``Wire.send``) will be sent to ``slave_address`` when ``void + Wire.endTransmission()`` is called. + +``void Wire.send(byte)`` + Queues the given byte (``uint8`` or ``int``) to the slave address + previously specified by a call to ``Wire.beginTransmission``. At + most 32 bytes may be queued in a single transmission. + +``Wire.send(string)`` + Queues a given string (``char*``) for transmission. The characters + of the string are individually queued for transmission as + bytes. At most 32 bytes may be queued in a single transmission. + +``Wire.send(buffer, length)`` + Queues a byte buffer ``buffer`` (``uint8*`` or ``int*``), with + ``length`` elements, for transmission. At most 32 bytes may be + queued in a single transmission. + +``Wire.endTransmission()`` + Ends a transmission (begun by ``Wire.beginTransmission(uint8)``), + and actually sends the bytes queued by calls to Wire.send. + + The return value is one of the following status codes: + + * ``SUCCESS``: All bytes were transmitted successfully. + + * ``EDATA``: More than 32 bytes were queued for transmission. No + bytes are actually sent when this happens. + + * ``ENACKADDR``: Did not receive ACK on transmit of address. No + bytes are actually sent when this happens. + + * ``ENACKTRNS``: Did not receive ACK during transmit of data. Some + bytes may have been sent when this happens; however, the + transmission is aborted after the first byte of data which is + not ACKed by the slave device. + + * ``EOTHER``: Other error occurred. + +``Wire.requestFrom(address, num_bytes)`` + Requests ``num_bytes`` bytes from 7-bit slave address + address. Returns the actual number of bytes read. These bytes may + subsequently be read one at a time using ``Wire.receive()``. + + Note: if ``num_bytes`` exceeds the size of the transmit/receive + buffer (currently 32), it will be truncated to 32. + +``Wire.receive()`` + Get and return the next byte read during the previous call to + ``Wire.requestFrom(uint8, int)``. You can check how many bytes are + left to read using ``uint8 Wire.available()``. + +``Wire.available()`` + Returns the number of bytes which are still available for reading + (with ``Wire.receive()``) from the last call to + ``Wire.requestFrom(uint8, int)``. -- cgit v1.2.3