aboutsummaryrefslogtreecommitdiffstats
path: root/libmaple/include
Commit message (Collapse)AuthorAgeFilesLines
* usb_cdcacm: Expose line coding state.Marti Bolivar2012-08-041-0/+27
| | | | | | | This was already supported, so just move the line coding structure to the header and add some functions for accessing the current values. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* usb_cdcacm: various fixups.Marti Bolivar2012-08-041-25/+0
| | | | | | | | | | Mark internal state static. Properly reset the RX/TX state on USB reset. Choose better names for countTx and newBytes. Move the exposed configuration back into the .c; this information is not beneficial to hooks. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* usb_cdcacm: Rename "notification" -> "management".Marti Bolivar2012-08-011-4/+4
| | | | | | This keeps things in line with the specification, helping readability. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* Move bootloader details out of libmaple.h.Marti Bolivar2012-07-311-8/+0
| | | | | | Finally! Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* Move bootloader reset signal detection to Wirish.Marti Bolivar2012-07-311-1/+0
| | | | | | | | Use usb_cdcacm hooks to move the DTR edge and "1EAF" magic packet detection to usb_serial.cpp. We'll later be able to extend this system to support Leonardo-style reset signalling. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* usb_cdcacm: Add usb_cdcacm_peek().Marti Bolivar2012-07-311-0/+1
| | | | | | | | | | | We need this so the bootloader reset signal detector can look ahead in the byte stream without stealing bytes from the user when "1EAF" isn't received. While we're doing this, take the time to fix a bunch of RX-related code (dead code removal, adding volatile, etc.) Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* usb_cdcacm: Add hook system.Marti Bolivar2012-07-311-0/+13
| | | | | | | | Provide hooks so users can reach into the CDC ACM callbacks with their own code. We'll use this to move the bootloader reset signals to Wirish. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* usb_cdcacm: Expose some internal configuration and values.Marti Bolivar2012-07-311-0/+42
| | | | | | | | | Mark the API as unstable so people don't rely on these too hard. (This header is not part of the official libmaple docs). We'll need some of this configuration elsewhere later, and it doesn't make much sense to expose it piecemeal. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* <libmaple/scb.h>: Add FIXME to check for F2 compatibility.Marti Bolivar2012-07-131-0/+4
| | | | Signed-off-by: Marti Bolivar <mbolivar@lozenge.(none)>
* <libmaple/scb.h>: Don't use BIT().Marti Bolivar2012-07-131-60/+60
| | | | | | Also, assert copyright LeafLabs 2012. Signed-off-by: Marti Bolivar <mbolivar@lozenge.(none)>
* <libmaple/scb.h>: Assert LeafLabs copyright.Marti Bolivar2012-07-131-0/+1
| | | | Signed-off-by: Marti Bolivar <mbolivar@lozenge.(none)>
* Doxygen hacks and fixups.Marti Bolivar2012-06-284-14/+11
| | | | | | | | - Shut Doxygen up in various places - Fix some genuine docs bugs - Ignore sources we're not responsible for Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* <libmaple/i2c.h>: Add I2C_CCR_DUTY bit value definitions.Marti Bolivar2012-06-221-1/+3
| | | | Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* i2c_dev: deprecate .gpio_port.Marti Bolivar2012-06-221-1/+18
| | | | | | | | | | | | | This won't work on F2, which at times has SDA and SCL on different ports (e.g. I2C3 SDA on PC9, SCL on PA8). Add .sda_port and .scl_port replacements, which are used when the now-deprecated .gpio_port is null. Use them correctly everywhere, with some new i2c_private.h helper functionality. Sigh. The F1 I2C code tries too hard to guess what you wanted; it's not porting well at all. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* I2C: Deprecate I2C_REMAP flag.Marti Bolivar2012-06-221-1/+1
| | | | | | | | This is ad-hoc and nonportable. If you really want I2C mapped elsewhere, then mess with the I2C device fields and call afio_remap() yourself. (This is also cleaner for F2). Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* I2C: Move F1-only errata workarounds out of libmaple/i2c.c.Marti Bolivar2012-06-221-0/+18
| | | | | | | | | The IRQ priority hack is unnecessary on targets with properly functioning I2C IRQ handlers, so we shouldn't use it unless we have to. Add a mechanism so a series header can provide such a hack if necessary. Have the F1 series header use this mechanism. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* I2C: Add i2c_config_gpios(), i2c_master_release_bus().Marti Bolivar2012-06-221-0/+25
| | | | | | These are necessary to pull out some calls to gpio_set_mode(). Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* <libmaple/i2c.h>: Fix Doxygen.Marti Bolivar2012-06-221-3/+3
| | | | | | | Existing Doxygen was commenting I2C_IRQ_ERROR instead of i2c_enable_irq(), as desired. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* libmaple/i2c.h: Better comments.Marti Bolivar2012-06-221-2/+16
| | | | Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* <libmaple/i2c.h>: Move low-level routines to end of file.Marti Bolivar2012-06-221-71/+73
| | | | Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* I2C: Fix Doxygen F1-isms.Marti Bolivar2012-06-221-3/+6
| | | | | | | | I'm not sure these functions should even exist in their present form,, but I don't understand the code well enough to make a real fix. For now, just replace references to RM0008 with "chip reference manual". Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* i2c_set_input_clk(): fix an F1-ism.Marti Bolivar2012-06-221-1/+16
| | | | | | | | | | | | | | | i2c_set_input_clk()'s documentation says that the maximum peripheral clock frequency is 36 MHz, but that's a hard-coded magic number. The actual limit is the device's APB frequency or 46 MHz, whichever is lower (F2 and F4 share the 46 MHz limit). Fix the documentation to reflect that fact, and add an internal series-provided function to get the maximum clock frequency for a device. To help users porting to F2, have i2c_set_input_clk() assert-check that the provided frequency is less than that maximum value and the hard 46 MHz limit. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* Move i2c_dev and i2c_state into new i2c_common.h.Marti Bolivar2012-06-222-27/+80
| | | | | | | This is necessary to add series-specific infrastructure to clean up some F1-isms in <libmaple/i2c.h>'s inline functions. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* libmaple/i2c.h: Cosmetics.Marti Bolivar2012-06-221-1/+4
| | | | Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* I2C: Restore on F1, refactoring prep for F2.Marti Bolivar2012-06-221-16/+1
| | | | | | | | | | | | | | | | | | | | | | | | | Bring back <libmaple/i2c.h> support on STM32F1 with a view towards how it'll be implemented on STM32F2. There are still many F1-isms in libmaple/i2c.c and <libmaple/i2c.h>, to be dealt with subsequently. Move device declarations and base pointer definitions to a new F1 <series/i2c.h>. The register maps and bit definitions themselves are identical on both series, so leave them in the libmaple header. Add i2c_private.h, which contains: - I2C_DEV(), a convenience macro for defining an i2c_dev, and - declarations for the event and error IRQ handlers. The IRQ handlers are large, and I2C is slow anyway, so I see no reason to make them inline in the private header (as we do for some other peripherals). We just expose the existing ones that were formerly static in libmaple/i2c.c, but prefix the names with underscore. Move the device declarations and IRQ handlers into new stm32f1/i2c.c. These use the i2c_private.h API. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* <libmaple/i2c.h>: Cosmetics.Marti Bolivar2012-06-221-6/+6
| | | | | | Put CCR definitions after SR2, to keep them in register map order. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* <libmaple/i2c.h>: Cosmetics.Marti Bolivar2012-06-221-20/+20
| | | | | | | Reorder register bit definitions by descending bit number, for consistency with the rest of the library. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* <libmaple/i2c.h>: Add missing register bit defns.Marti Bolivar2012-06-221-0/+22
| | | | Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* libmaple/i2c.h: Assert LeafLabs copyright.Marti Bolivar2012-06-221-0/+1
| | | | Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* Fix I2C_CR2_FREQ bit definition.Marti Bolivar2012-06-221-1/+1
| | | | | | The existing value clobbers the entire register. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* libmaple/i2c.h: Cosmetics.Marti Bolivar2012-06-221-1/+1
| | | | Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* libmaple/i2c.h: Don't use BIT().Marti Bolivar2012-06-221-40/+40
| | | | Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* <libmaple/dma.h>: Assert LeafLabs copyright.Marti Bolivar2012-06-211-0/+1
| | | | Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* DMA: prep for F2 with new "tube" API.Marti Bolivar2012-06-152-26/+490
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To prepare for STM32F2/F4 DMA support, introduce a new libmaple DMA API, and move some code around to make priority level and interrupt handling more generic. The new API is based on a new set of types (dma_tube, struct dma_tube_reg_map, enum dma_request_src, enum dma_cfg_flags, and struct dma_tube_config). The central abstraction is the dma_tube type. STM32F2/F4 use DMA streams to control dataflow, and STM32F1 uses channels. dma_tube stands for whichever is appropriate for the current target. Dealing with tubes allows for configuring and using DMA with opaque tube values in the same source, instead of (as with ST's firmware) requiring two separate codebases. The new API is also more user-friendly, as it doesn't require knowing which DMA address registers to set and which configuration register flags go along with them. It now suffices to specify the source and destination for the DMA transfer, along with their sizes. This avoids confusion (e.g. for memory-to-memory transfers, data flows from the peripheral address register to the memory register, which might be surprising on F2, which has two memory address registers). The old API (based on enum dma_mode_flags and dma_setup_transfer()) is still available on F1, but deprecate it. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* enum spi_mode: Add more descriptive enumerators, documentation.Marti Bolivar2012-06-071-11/+16
| | | | | | | | | Instead of requiring everyone to figure it out for themselves, add enumerators specifying the idle logic level and what clock edge triggers data capture. Yes, it's easy enough to figure it out. It's also convenient to have these. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* Bring back <libmaple/spi.h>.Marti Bolivar2012-06-071-1/+1
| | | | | | | | | | | Add a spi_private.h with a SPI_DEV(), for convenience. Use it in the F1 and F2 implementations. We could probably unify these with an STM32_HAVE_SPI(n) macro, but we'll leave that for the future. Most everything from F1 is portable; F2 has some additional bit definitions and a spi_get_af() routine, but that's about it. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* libmaple/timer.h: Capitalization fixMarti Bolivar2012-06-071-2/+2
| | | | Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* libmaple/timer.h: Lose BIT().Marti Bolivar2012-06-071-90/+90
| | | | Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* libmaple/timer.h: Move deprecated bits to bottom.Marti Bolivar2012-06-071-66/+67
| | | | Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* struct timer_dev: Don't touch ->handlers!Marti Bolivar2012-06-071-3/+1
| | | | Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* libmaple/timer.h: Nuke useless comment.Marti Bolivar2012-06-071-1/+1
| | | | Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* libmaple/timer.h: Doxygen beautification and fixupsMarti Bolivar2012-06-071-98/+109
| | | | | | | Make the Doxygen comments nicer to look at. Some of the docstrings are out-of-date since F2 support was added, so update them. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* Move timer_dev definitions into libmaple/timer.c.Marti Bolivar2012-06-071-0/+42
| | | | | | | | | The addition of STM32_HAVE_TIMER() allows us to avoid some repetition. There's still an issue with names on F1 preventing us from moving the IRQ handlers to libmaple/timer.c, but once that's resolved, we'll be able to remove even more. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* Bring back libmaple/dac.h.Marti Bolivar2012-06-041-68/+56
| | | | | | | Minor variations on F2: DMA underrun interrupts, and a status register to hold the notification bits. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* stm32.h: Add STM32_HAVE_DAC feature-test.Marti Bolivar2012-06-041-0/+6
| | | | Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* STM32F2: Add EXTI support.Marti Bolivar2012-06-031-3/+1
| | | | | | | | Add series headers to keep the base pointers, and (on F2) use SYSCFG to tell exti_do_select() where the EXTI control registers are. No surprises. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* STM32F2: Add SYSCFG support.Marti Bolivar2012-06-031-0/+151
| | | | | | Turn it on at init() time on F2. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* Bring back EXTI on F1, with deprecations for gpio.h on F1.Marti Bolivar2012-06-032-14/+105
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Tested on Maple Mini with examples/mini-exti-test. Changes to Wirish are minor: use the new EXTI types exti_num and exti_cfg (see below) in place of now-deprecated variants in ext_interrupts.cpp. The way I originally did libmaple/exti.h was stupid, and fixing it turned out to be a little disruptive. libmaple/exti.h depends on libmaple/gpio.h (for AFIO), but that's a classic case of exposed implementation detail. So invert the dependency: make gpio.h depend on exti.h. Do this by adding exti_num and exti_cfg to exti.h; these respectively replace afio_exti_num and afio_exti_port. The afio_* variants are now deprecated. (Throw in a typedef and some macros at the bottom of the F1 series/gpio.h for backwards compatibility). Make exti_attach_interrupt() and exti_detach_interrupt() take exti_num/exti_cfg arguments instead of the afio_* variants. Make the EXTI dispatch routines __always_inline to defeat GCC -Os. Many renames throughout libmaple/stm32f1/ to stop using the deprecated names. Also move the previously F1-only gpio_exti_port() function into the public libmaple header. Reimplementing it in terms of rcc_clk_ids lets us deprecate the gpio_dev->exti_port field, which will save space in the future. While we're there, I notice that struct gpio_dev is defined once per series. That's dumb, as it misses the entire point of having device structs: they contain what's portable. So put the F1 version (which has the extra EXTI port field) into libmaple/gpio.h, and add the necessary exti_ports to libmaple/stm32f2/gpio.c. Sigh. We'll get rid of it eventually, at least. Clean up some other mistakes in gpio.h files as well (mostly removing util.h dependency). Sorry for the messy commit. For portability, add a new series-specific exti function, exti_select(). The F1 version in (new) libmaple/stm32f1/exti.c uses AFIO and some new private functionality in libmaple/exti.c and (new) libmaple/exti_private.h to make this convenient. We'll be able to do the SYSCFG equivalent on F2 without any trouble. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* <libmaple/bitband.h>: DoxygenMarti Bolivar2012-06-031-2/+2
| | | | Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
* Slightly improve and generify the USB infrastructure.Marti Bolivar2012-06-031-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The good news is that <libmaple/usb.h> and <libmaple/usb_cdcacm.h> did turn out generic enough in what they specify to go on unchanged. However, we can't just go on assuming that there's USB just because we're on an F1. Now that there's value line in the tree, we need to be more careful (value line F1s don't have USB peripherals). To that end, make all the F1 board-includes/*.mk files specify what line their MCU is with an MCU_F1_LINE variable. Use that to hack libmaple/usb/rules.mk so we only try to build the USB module under appropriate circumstances. While we're at it, add a vector_symbols.inc for value line MCUs under support/ld/. We need this to get the target-config.mk modifications implied by the addition of MCU_F1_LINE. We'll fix up some other performance-line-isms under libmaple/stm32f1 in a separate commit. Also in libmaple/usb/: - Move everything into a new stm32f1 directory. Due to aforementioned rules.mk hacks, there is no immediate need for an stm32f2 directory (USB support doesn't exist there). - Update the README for style and content. Signed-off-by: Marti Bolivar <mbolivar@leaflabs.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-24 03:00:08 +0000