1 files changed, 87 insertions, 0 deletions
diff --git a/src/stm32lib/examples/USART/Smartcard/readme.txt b/src/stm32lib/examples/USART/Smartcard/readme.txt
new file mode 100755
index 0000000..615be2a
--- /dev/null
+++ b/src/stm32lib/examples/USART/Smartcard/readme.txt
@@ -0,0 +1,87 @@
+/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
+* File Name          : readme.txt
+* Author             : MCD Application Team
+* Version            : V2.0.1
+* Date               : 06/13/2008
+* Description        : Description of the USART Smartcard Example.
+********************************************************************************
+* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
+* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
+* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
+* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
+* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+*******************************************************************************/
+
+Example description
+===================
+This example provides a description of how  to use the USART in Smartcard mode. 
+The example gives only the possibility to read the ATR and decode it into 
+predefined buffer.
+First, the code is waiting for an card insertion. If a card is detected through
+the EXTI Line interrupt (connected to the Smartcard detect pin), a reset signal
+is applied to the card through its reset pin.
+As response to this reset, the card transmit the ATR which will be stored in 
+predefined buffer. Once the ATR is received, it is decoded and stored in a specific
+structure (SC_A2R) and the card protocol type is stored in a variable.
+ATRDecodeStatus variable must be equal to 1 (PASSED) when the sequence succeed.
+
+The used Smartcard should be ISO7816-3 T=0 compatible.
+
+USART3 configured as follow:
+  - Word Length = 9 Bits
+  - 0.5 Stop Bit
+  - Even parity
+  - BaudRate = 12096 baud
+  - Hardware flow control disabled (RTS and CTS signals)
+  - Tx and Rx enabled
+  - USART Clock enabled
+  - USART CPOL: Clock is active low
+  - USART CPHA: Data is captured on the second edge 
+  - USART LastBit: The clock pulse of the last data bit is not output to 
+                   the SCLK pin
+
+
+Directory contents
+==================
+platform_config.h    Evaluation board specific configuration file
+stm32f10x_conf.h     Library Configuration file
+stm32f10x_it.h       Interrupt handlers header file
+stm32f10x_it.c       Interrupt handlers
+main.c               Main program
+
+
+Hardware environment
+====================
+This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
+boards and can be easily tailored to any other hardware.
+To select the STMicroelectronics evaluation board used to run the example, uncomment
+the corresponding line in platform_config.h file.
+
+ + STM3210B-EVAL 
+    - Plug a Smartcard (ISO7816-3 T=0 compatible) into the dedicated Smartcard 
+      connector CN16.
+ 
+ + STM3210E-EVAL
+    - Plug a Smartcard (ISO7816-3 T=0 compatible) into  the dedicated Smartcard 
+      connector CN18.
+    - Make sure that Jumper 15 (JP15) and Jumper 16 (JP16) are fitted.
+
+  
+How to use it
+=============
+In order to make the program work, you must do the following :
+- Create a project and setup all your toolchain's start-up files
+- Compile the directory content files and required Library files :
+  + stm32f10x_lib.c
+  + stm32f10x_gpio.c
+  + stm32f10x_rcc.c
+  + stm32f10x_usart.c
+  + stm32f10x_nvic.c
+  + stm32f10x_flash.c
+  + stm32f10x_exti.c
+        
+- Link all compiled files and load your image into target memory
+- Run the example
+
+******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******