1 files changed, 0 insertions, 89 deletions
diff --git a/src/stm32lib/examples/USART/Printf/readme.txt b/src/stm32lib/examples/USART/Printf/readme.txt
deleted file mode 100755
index 3bc3309..0000000
--- a/src/stm32lib/examples/USART/Printf/readme.txt
+++ /dev/null
@@ -1,89 +0,0 @@
-/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
-* File Name          : readme.txt
-* Author             : MCD Application Team
-* Version            : V2.0.1
-* Date               : 06/13/2008
-* Description        : Description of the USART Printf Example.
-********************************************************************************
-* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
-* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
-* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
-* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
-* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
-* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
-*******************************************************************************/
-
-Example description
-===================
-This example shows how to retarget the C library printf function to the USART. 
-This implementation output the printf message on the Hyperterminal using USARTx.
-USARTx can be USART1, USART2, USART3, UART4 or UART5; to select the USART 
-interface to be used uncomment the '#define USE_USARTx' line in 'platform_config.h'
-file.
-
-The USARTx is configured as follow:
-    - BaudRate = 115200 baud  
-    - Word Length = 8 Bits
-    - One Stop Bit
-    - No parity
-    - Hardware flow control disabled (RTS and CTS signals)
-    - Receive and transmit enabled
-
-
-Directory contents
-==================
-platform_config.h    Evaluation board specific configuration file
-stm32f10x_conf.h     Library Configuration file
-stm32f10x_it.h       Interrupt handlers header file
-stm32f10x_it.c       Interrupt handlers
-main.c               Main program
-
-
-Hardware environment
-====================
-This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
-boards and can be easily tailored to any other hardware.
-To select the STMicroelectronics evaluation board used to run the example, uncomment
-the corresponding line in platform_config.h file.
-
- + The USARTx signals (Rx, Tx) must be connected to a DB9 connector using a RS232
-   transceiver. 
- 
- + Connect a null-modem female/female RS232 cable between the DB9 connector 
-   and PC serial port. 
-
- + STM3210B-EVAL 
-    - Connect a null-modem female/female RS232 cable between the DB9 connector 
-      (CN6 for USART1, CN5 for USART2 in the STM3210B-EVAL board) 
-      and PC serial port.
- 
- + STM3210E-EVAL
-    - Connect a null-modem female/female RS232 cable between the DB9 connector 
-      (CN12 for USART1, CN8 for USART2 in the STM3210E-EVAL board) 
-      and PC serial port.
- 
-
- - Hyperterminal configuration:
-    - Word Length = 8 Bits
-    - One Stop Bit
-    - No parity
-    - BaudRate = 115200 baud
-    - flow control: None 
-
-
-How to use it
-=============
-In order to make the program work, you must do the following :
-- Create a project and setup all your toolchain's start-up files
-- Compile the directory content files and required Library files :
-  + stm32f10x_lib.c
-  + stm32f10x_usart.c
-  + stm32f10x_gpio.c
-  + stm32f10x_rcc.c
-  + stm32f10x_nvic.c
-  + stm32f10x_flash.c
-    
-- Link all compiled files and load your image into target memory
-- Run the example
-
-******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******