1 files changed, 87 insertions, 0 deletions
diff --git a/src/stm32lib/examples/USART/MultiProcessor/readme.txt b/src/stm32lib/examples/USART/MultiProcessor/readme.txt
new file mode 100755
index 0000000..dd3c62f
--- /dev/null
+++ b/src/stm32lib/examples/USART/MultiProcessor/readme.txt
@@ -0,0 +1,87 @@
+/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
+* File Name          : readme.txt
+* Author             : MCD Application Team
+* Version            : V2.0.1
+* Date               : 06/13/2008
+* Description        : Description of the USART Multi Processor Example.
+********************************************************************************
+* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
+* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
+* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
+* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
+* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+*******************************************************************************/
+
+Example description
+===================
+This example provides a description of how to use the USART in multi-processor mode.
+First, the USART1 and USART2 address are set to 0x1 and 0x2. The USART1 send 
+continusouly the character 0x33 to the USART2. The USART2 toggle LD1, LD2, LD3 
+and LD4 pins while receiving 0x33.
+
+When a falling edge is applied on Key Button EXTI line, an interrupt is generated
+and in the EXTI9_5_IRQHandler routine, the USART2 is entred in mute mode and still
+in this mode (no LED toggling) until a rising edge is applied on EXTI Line 0.
+In this interrupt routine the USART1 send the character of address mark (0x102)
+to wakeup USART2. The LED restart toggling.
+
+USART1 and USART2 configured as follow:
+  - BaudRate = 9600 baud  
+  - Word Length = 9 Bits
+  - One Stop Bit
+  - No parity
+  - Hardware flow control disabled (RTS and CTS signals)
+  - Receive and transmit enabled
+
+
+Directory contents
+==================
+platform_config.h    Evaluation board specific configuration file
+stm32f10x_conf.h     Library Configuration file
+stm32f10x_it.h       Interrupt handlers header file
+stm32f10x_it.c       Interrupt handlers
+main.c               Main program
+
+
+Hardware environment
+====================
+This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
+boards and can be easily tailored to any other hardware.
+To select the STMicroelectronics evaluation board used to run the example, uncomment
+the corresponding line in platform_config.h file.
+
+ + STM3210B-EVAL 
+    - Connect a null-modem female/female RS232 cable between CN5 and CN6.
+    - Note: in this case USART2 Tx and Rx pins are remapped by software on 
+            PD.05 and PD.06 respectively. 
+    - Use Key push-button connected to pin PB.09 (EXTI Line9)
+    - Use Wakeup push-button connected to pin PA.00 (EXTI Line0)
+    - Use LD1, LD2, LD3 and LD4 leds connected respectively to PC.06, PC.07, PC.08
+      and PC.09 pins             
+ 
+ + STM3210E-EVAL
+    - Connect a null-modem female/female RS232 cable between CN12 and CN8.
+    - Use Key push-button connected to pin PG.08 (EXTI Line8)
+    - Use Wakeup push-button connected to pin PA.00 (EXTI Line0)
+    - Use LD1, LD2, LD3 and LD4 leds connected respectively to PF.06, PF0.7, PF.08
+      and PF.09 pins
+    - Make sure that the Jumper 4 (JP4) is in position 1<-->2.    
+   
+How to use it
+=============
+In order to make the program work, you must do the following :
+- Create a project and setup all your toolchain's start-up files
+- Compile the directory content files and required Library files :
+  + stm32f10x_lib.c
+  + stm32f10x_gpio.c
+  + stm32f10x_rcc.c
+  + stm32f10x_usart.c
+  + stm32f10x_nvic.c
+  + stm32f10x_flash.c
+  + stm32f10x_exti.c
+  
+- Link all compiled files and load your image into target memory
+- Run the example
+
+******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******