1 files changed, 85 insertions, 0 deletions
diff --git a/src/stm32lib/examples/USART/IrDA/Receive/readme.txt b/src/stm32lib/examples/USART/IrDA/Receive/readme.txt
new file mode 100755
index 0000000..21d8a89
--- /dev/null
+++ b/src/stm32lib/examples/USART/IrDA/Receive/readme.txt
@@ -0,0 +1,85 @@
+/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
+* File Name          : readme.txt
+* Author             : MCD Application Team
+* Version            : V2.0.1
+* Date               : 06/13/2008
+* Description        : Description of the USART IrDA Receive Example.
+********************************************************************************
+* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
+* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
+* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
+* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
+* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+*******************************************************************************/
+
+Example description
+===================
+This example provides a basic communication USART3 IrDA receive mode. Four leds
+are used to show which byte is received. 
+
+  - LD1 toggle when 0x04 is received
+  - LD2 toggle when 0x05 is received
+  - LD3 toggle when 0x03 is received
+  - LD4 toggle when 0x02 is received
+  - LD1, LD2, LD3 and LD4 toggle when 0x01 is received        
+
+USART3 configured as follow:
+   - BaudRate = 115200 baud  
+   - Word Length = 8 Bits
+   - One Stop Bit
+   - No parity
+   - Hardware flow control disabled (RTS and CTS signals)
+   - Receive and transmit enabled
+
+The USART IrDA example provides two IrDA program: transmitter&receiver and requires two boards
+to be able to run the full demonstration:
+ - one board will act as IrDA transmitter
+ - one board will act as IrDA receiver
+
+
+Directory contents
+==================
+platform_config.h    Evaluation board specific configuration file
+stm32f10x_conf.h     Library Configuration file
+stm32f10x_it.h       Interrupt handlers header file
+stm32f10x_it.c       Interrupt handlers
+main.c               Main program
+
+
+Hardware environment
+====================
+This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
+boards and can be easily tailored to any other hardware.
+To select the STMicroelectronics evaluation board used to run the example, uncomment
+the corresponding line in platform_config.h file.
+
+ + STM3210B-EVAL 
+    - Use an IrDA tranceiver connected to the USART3 Tx pin (U11 connector, JP5 
+      jumper must be fitted).
+    - Use LD1, LD2, LD3 and LD4 leds connected respectively to PC.06, PC.07, PC.08
+      and PC.09 pins 
+ 
+ + STM3210E-EVAL
+    - Use an IrDA tranceiver connected to the USART3 Tx pin (U13 connector, JP21
+      and JP22 jumper must be fitted).
+    - Use LD1, LD2, LD3 and LD4 leds connected respectively to PF.06, PF0.7, PF.08
+      and PF.09 pins
+
+  
+How to use it
+=============
+In order to make the program work, you must do the following :
+- Create a project and setup all your toolchain's start-up files
+- Compile the directory content files and required Library files :
+  + stm32f10x_lib.c
+  + stm32f10x_gpio.c
+  + stm32f10x_rcc.c
+  + stm32f10x_usart.c
+  + stm32f10x_nvic.c
+  + stm32f10x_flash.c
+  
+- Link all compiled files and load your image into target memory
+- Run the example
+
+******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******