1 files changed, 83 insertions, 0 deletions
diff --git a/src/stm32lib/examples/TIM/OCActive/readme.txt b/src/stm32lib/examples/TIM/OCActive/readme.txt
new file mode 100755
index 0000000..4298faf
--- /dev/null
+++ b/src/stm32lib/examples/TIM/OCActive/readme.txt
@@ -0,0 +1,83 @@
+/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
+* File Name          : readme.txt
+* Author             : MCD Application Team
+* Version            : V2.0.1
+* Date               : 06/13/2008
+* Description        : Description of the TIM OCActive example.
+********************************************************************************
+* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
+* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
+* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
+* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
+* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+*******************************************************************************/
+
+Example description
+===================
+This example shows how to configure the TIM peripheral to generate four different 
+signals with four different delays.
+
+The TIMxCLK frequency is set to 36 MHz, the Prescaler is set to 35999 and used in 
+Output Compare Active Mode.
+ 
+TIM2 counter clock = TIMxCLK / (Prescaler +1) = 1 KHz 
+
+The TIM2 CCR1 register value is equal to 1000:
+TIM2_CH1 delay = CCR1_Val/TIM2 counter clock  = 1000 ms
+so the TIM2 Channel 1 generates a signal with a delay equal to 1000 ms.
+
+The TIM2 CCR2 register value is equal to 500:
+TIM2_CH2 delay = CCR2_Val/TIM2 counter clock = 500 ms
+so the TIM2 Channel 2 generates a signal with a delay equal to 500 ms.
+
+The TIM2 CCR3 register value is equal to 250:
+TIM2_CH3 delay = CCR3_Val/TIM2 counter clock = 250 ms
+so the TIM2 Channel 3 generates a signal with a delay equal to 250 ms.
+
+The TIM2 CCR4 register value is equal to 125:
+TIM2_CH4 delay = CCR4_Val/TIM2 counter clock = 125 ms
+so the TIM2 Channel 4 generates a signal with a delay equal to 125 ms.
+
+The delay correspond to the time difference between PC.06 and TIM2_CHx signal rising edges
+
+Directory contents
+==================
+stm32f10x_conf.h  Library Configuration file
+stm32f10x_it.c    Interrupt handlers
+stm32f10x_it.h    Interrupt handlers header file
+main.c            Main program
+ 
+
+Hardware environment
+====================
+This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
+boards and can be easily tailored to any other hardware.
+There is no need for any modification when switching between these two boards.
+
+Connect the:
+- PC.06
+- PA.00 (TIM2_CH1)
+- PA.01 (TIM2_CH2)
+- PA.02 (TIM2_CH3)
+- PA.03 (TIM2_CH4)
+pins to an oscilloscope to monitor the different waveforms.
+  
+  
+How to use it
+=============
+In order to make the program work, you must do the following:
+- Create a project and setup all your toolchain's start-up files
+- Compile the directory content files and required Library files:
+  + stm32f10x_lib.c
+  + stm32f10x_tim.c
+  + stm32f10x_gpio.c
+  + stm32f10x_rcc.c
+  + stm32f10x_nvic.c
+  + stm32f10x_flash.c
+
+- Link all compiled files and load your image into target memory
+- Run the example
+
+
+******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******