1 files changed, 95 insertions, 0 deletions
diff --git a/src/stm32lib/examples/TIM/ExtTrigger_Synchro/readme.txt b/src/stm32lib/examples/TIM/ExtTrigger_Synchro/readme.txt
new file mode 100755
index 0000000..78e8ace
--- /dev/null
+++ b/src/stm32lib/examples/TIM/ExtTrigger_Synchro/readme.txt
@@ -0,0 +1,95 @@
+/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
+* File Name          : readme.txt
+* Author             : MCD Application Team
+* Version            : V2.0.1
+* Date               : 06/13/2008
+* Description        : Description of the TIM ExTrigger_Synchro example.
+********************************************************************************
+* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
+* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
+* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
+* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
+* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+*******************************************************************************/
+
+Example description
+===================
+
+This example shows how to synchronize TIM peripherals in cascade mode with an
+external trigger.
+In this example three timers are used:
+
+1/TIM2 is configured as Master Timer:
+ - Toggle Mode is used
+ - The TIM2 Enable event is used as Trigger Output 
+ 
+2/TIM2 is configured as Slave Timer for an external Trigger connected to TIM2 TI2 pin 
+(TIM2 CH2 configured as input pin):
+ - The TIM2 TI2FP2 is used as Trigger Input
+ - Rising edge is used to enable and stop the TIM2: Gated Mode.
+  
+3/TIM3 is slave for TIM2 and Master for TIM4,
+ - Toggle Mode is used
+ - The ITR1(TIM2) is used as input trigger 
+ - Gated mode is used, so start and stop of slave counter are controlled by the Master
+   trigger output signal(TIM2 enable event).
+ - The TIM3 enable event is used as Trigger Output. 
+
+4/TIM4 is slave for TIM3,
+ - Toggle Mode is used
+ - The ITR2(TIM3) is used as input trigger
+ - Gated mode is used, so start and stop of slave counter are controlled by the Master 
+trigger output signal(TIM3 enable event).
+
+The TIMxCLK is fixed to 72 MHZ, the Prescaler is equal to 2 so the TIMx clock counter
+is equal to 24 MHz.
+The Three Timers are running at: 
+TIMx frequency = TIMx clock counter/ 2*(TIMx_Period + 1) = 162.1 KHz.
+
+The starts and stops of the TIM2 counter are controlled by the external trigger.
+The TIM3 starts and stops are controlled by the TIM2, and the TIM4 starts and stops 
+are controlled by the TIM3.	 
+  
+
+Directory contents
+==================
+stm32f10x_conf.h  Library Configuration file
+stm32f10x_it.c    Interrupt handlers
+stm32f10x_it.h    Interrupt handlers header file
+main.c            Main program
+ 
+
+Hardware environment
+====================
+This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
+boards and can be easily tailored to any other hardware.
+There is no need for any modification when switching between these two boards.
+
+- Connect an external trigger, with a frequency <= 40KHz, to the TIM2 CH2 pin (PA.01).
+  In this example the frequency is equal to 5 KHz.
+
+- Connect the:
+  - TIM2 CH1 (PA.00)
+  - TIM3 CH1 (PA.06)
+  - TIM4 CH1 (PB.06) 
+  pins to an oscilloscope to monitor the different waveforms.
+   
+  
+How to use it
+=============
+In order to make the program work, you must do the following:
+- Create a project and setup all your toolchain's start-up files
+- Compile the directory content files and required Library files:
+  + stm32f10x_lib.c
+  + stm32f10x_tim.c
+  + stm32f10x_gpio.c
+  + stm32f10x_rcc.c
+  + stm32f10x_nvic.c
+  + stm32ff10x_flash.c
+
+- Link all compiled files and load your image into target memory
+- Run the example
+
+
+******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******