1 files changed, 93 insertions, 0 deletions
diff --git a/src/stm32lib/examples/TIM/6Steps/readme.txt b/src/stm32lib/examples/TIM/6Steps/readme.txt
new file mode 100755
index 0000000..980d67e
--- /dev/null
+++ b/src/stm32lib/examples/TIM/6Steps/readme.txt
@@ -0,0 +1,93 @@
+/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
+* File Name          : readme.txt
+* Author             : MCD Application Team
+* Version            : V2.0.1
+* Date               : 06/13/2008
+* Description        : Description of the TIM 6Steps example.
+********************************************************************************
+* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
+* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
+* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
+* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
+* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+*******************************************************************************/
+
+Example description
+===================
+This example shows how to configure the TIM1 peripheral to generate 6 Steps.
+The STM32F10x TIM1 peripheral offers the possibility to program in advance the 
+configuration for the next TIM1 outputs behaviour (step) and change the configuration
+of all the channels at the same time. This operation is possible when the COM 
+(commutation) event is used.
+The COM event can be generated by software by setting the COM bit in the TIM1_EGR
+register or by hardware (on TRC rising edge).
+In this example, a software COM event is generated each 100 ms: using the SysTick 
+interrupt.
+The TIM1 is configured in Timing Mode, each time a COM event occurs, a new TIM1
+configuration will be set in advance.
+
+The break Polarity is used at High level.
+
+The following Table describes the TIM1 Channels states:
+
+              -----------------------------------------------
+             | Step1 | Step2 | Step3 | Step4 | Step5 | Step6 |
+   ----------------------------------------------------------
+  |Channel1  |   1   |   0   |   0   |   0   |   0   |   1   |
+   ----------------------------------------------------------
+  |Channel1N |   0   |   0   |   1   |   1   |   0   |   0   |
+   ----------------------------------------------------------
+  |Channel2  |   0   |   0   |   0   |   1   |   1   |   0   |
+   ----------------------------------------------------------
+  |Channel2N |   1   |   1   |   0   |   0   |   0   |   0   |
+   ----------------------------------------------------------
+  |Channel3  |   0   |   1   |   1   |   0   |   0   |   0   |
+   ----------------------------------------------------------
+  |Channel3N |   0   |   0   |   0   |   0   |   1   |   1   |
+   ----------------------------------------------------------
+
+
+Directory contents
+==================
+stm32f10x_conf.h  Library Configuration file
+stm32f10x_it.c    Interrupt handlers
+stm32f10x_it.h    Interrupt handlers header file
+main.c            Main program
+
+
+Hardware environment
+====================
+This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
+boards and can be easily tailored to any other hardware.
+There is no need for any modification when switching between these two boards.
+
+- Connect the TIM1 pins to an oscilloscope to monitor the different waveforms:
+    - TIM1_CH3  pin (PA.10)
+    - TIM1_CH1N pin (PB.13)  
+    - TIM1_CH2  pin (PA.09)  
+    - TIM1_CH3N pin (PB.15)
+    - TIM1_CH1  pin (PA.08)  
+    - TIM1_CH2N pin (PB.14)  
+  
+- Connect the TIM1 break pin TIM1_BKIN pin (PB.12) to the GND. To generate a break
+  event, switch this pin level from 0V to 3.3V.  
+
+  
+How to use it
+=============
+In order to make the program work, you must do the following:
+- Create a project and setup all your toolchain's start-up files
+- Compile the directory content files and required Library files:
+  + stm32f10x_lib.c
+  + stm32f10x_tim.c
+  + stm32f10x_gpio.c
+  + stm32f10x_rcc.c
+  + stm32f10x_nvic.c
+  + stm32f10x_flash.c
+  + stm32f10x_systick.c
+  
+- Link all compiled files and load your image into target memory
+- Run the example
+
+******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******