1 files changed, 86 insertions, 0 deletions
diff --git a/src/stm32lib/examples/SPI/CRC/readme.txt b/src/stm32lib/examples/SPI/CRC/readme.txt
new file mode 100755
index 0000000..37df508
--- /dev/null
+++ b/src/stm32lib/examples/SPI/CRC/readme.txt
@@ -0,0 +1,86 @@
+/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
+* File Name          : readme.txt
+* Author             : MCD Application Team
+* Version            : V2.0.1
+* Date               : 06/13/2008
+* Description        : Description of the SPI CRC Example.
+********************************************************************************
+* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
+* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
+* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
+* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
+* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+*******************************************************************************/
+
+Example description
+===================
+This example provides a description of how to set a communication between two
+SPIs in full-duplex mode and performs a transfer from Master to Slave and  
+Slave to Master followed by CRC transmission.
+
+SPI1 is configured as master and SPI2 as slave and both are in full-duplex
+configuration mode with 16bit data size and a 4.5Mbit/s communication speed.
+CRC calculation is enabled for both SPIs.
+
+After enabling both SPIs, the first data from SPI2_Buffer_Tx is transmitted from
+slave followed by the first data from SPI1_Buffer_Tx send by the master. A test 
+on RxNE flag is done for both master and slave to check the reception of data on
+their respective data register. The same procedure is done for the remaining data
+to transfer except the last ones. 
+
+Last data from SPI1_Buffer_Tx is transmitted followed by enabling CRC transmission
+for SPI1 and the last data from SPI2_Buffer_Tx is transmitted followed by enabling
+CRC transmission for SPI2: user must take care to reduce code on this phase for
+high speed communication. 
+
+Last transmitted buffer data and CRC value are then received successively on
+master and slave data registers. The received CRC value are stored on CRC1Value
+and CRC2Value respectively for SPI1 and SPI2.
+
+Once the transfer is completed a comparison is done and TransferStatus1 and 
+TransferStatus2 gives the data transfer status for each data transfer direction 
+where it is PASSED if transmitted and received data are the same otherwise it 
+is FAILED.
+A check of CRC error flag, for the master and the salve, is done after receiving
+CRC data.
+
+
+Directory contents
+==================
+stm32f10x_conf.h     Library Configuration file
+stm32f10x_it.c       Interrupt handlers
+stm32f10x_it.h       Header for stm32f10x_it.c
+main.c               Main program
+
+
+Hardware environment
+====================
+This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
+boards and can be easily tailored to any other hardware.
+There is no need for any modification when switching between these two boards.
+
+ - Connect SPI1 SCK (PA.05) pin to SPI2 SCK (PB.13) pin
+ - Connect SPI1 MISO (PA.06) pin to SPI2 MISO (PB.14) pin
+ - Connect SPI1 MOSI (PA.07) pin to SPI2 MOSI (PB.15) pin
+
+Note: in STM3210E-EVAL board, the jumper 14 (USB Disconnect) must be set in 
+      position 1<->2 in order to not interfer with SPI2 MISO pin PB14.
+       
+How to use it
+=============
+In order to make the program work, you must do the following:
+- Create a project and setup all your toolchain's start-up files
+- Compile the directory content files and required Library files:
+  + stm32f10x_lib.c
+  + stm32f10x_spi.c
+  + stm32f10x_rcc.c
+  + stm32f10x_gpio.c
+  + stm32f10x_nvic.c
+  + stm32f10x_flash.c
+    
+- Link all compiled files and load your image into target memory
+- Run the example
+
+
+******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******