1 files changed, 0 insertions, 79 deletions
diff --git a/src/stm32lib/examples/SDIO/readme.txt b/src/stm32lib/examples/SDIO/readme.txt
deleted file mode 100755
index 54d6cd1..0000000
--- a/src/stm32lib/examples/SDIO/readme.txt
+++ /dev/null
@@ -1,79 +0,0 @@
-/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
-* File Name          : readme.txt
-* Author             : MCD Application Team
-* Version            : V2.0.1
-* Date               : 06/13/2008
-* Description        : Description of the SDIO Example.
-********************************************************************************
-* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
-* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
-* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
-* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
-* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
-* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
-*******************************************************************************/
-
-Example description
-===================
-This example provides a basic example of how to use the SDIO firmware library and
-an associate driver to perform read/write operations on the SD Card memory 
-mounted on the STM3210E-EVAL board.
-Below is a description of the different example steps:
-  - Configure the SDIO according to the desired SDIO_CK clock frequency.
-  - Reset the SD Card
-  - Identify the SD Card
-  - Initializes the SD Card
-  - Get the SD Card Info
-  - Select the SD Card
-  - Enable the Wide Bus mode (4-bit data)
-  - Erase the correponding blocks
-  - Read the Erased blocks
-  - Test if the corresponding Blocks are well erased: check if the EraseStatus 
-    variable is equal to PASSED.
-  - Set the Data Transfer Mode to DMA   
-  - Write a single Block             
-  - Read a single Block
-  - Comapare the written Block and the read one: check if the TransferStatus1 
-    variable is equal to PASSED.
-  - Write multiple Blocks (2)             
-  - Read multiple Blocks (2)
-  - Comapare the written Blocks and the read one: check if the TransferStatus2 
-    variable is equal to PASSED.  
-
-
-Directory contents
-==================
-stm32f10x_conf.h  Library Configuration file
-stm32f10x_it.c    Interrupt handlers
-stm32f10x_it.h    Header for stm32f10x_it.c
-sdcard.c          SD Card Driver file
-sdcard.h          Header for sdcard.c
-main.c            Main program
-
-
-Hardware environment
-====================
-This example runs on STMicroelectronics STM3210E-EVAL evaluation board and can be
-easily tailored to any other hardware.
-
-Note: make sure that the Jumper 17 (JP17) is closed and Jumper 20 (JP20) is open
-      in STM3210E-EVAL 
-
-
-How to use it
-=============
-In order to make the program work, you must do the following:
-- Create a project and setup all your toolchain's start-up files
-- Compile the directory content files and required Library files:
-  + stm32f10x_lib.c
-  + stm32f10x_gpio.c
-  + stm32f10x_rcc.c
-  + stm32f10x_nvic.c
-  + stm32f10x_flash.c
-  + stm32f10x_sdio.c
-  + stm32f10x_dma.c
-  
-- Link all compiled files and load your image into either RAM or Flash
-- Run the example
-
-******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******