1 files changed, 79 insertions, 0 deletions
diff --git a/src/stm32lib/examples/SDIO/readme.txt b/src/stm32lib/examples/SDIO/readme.txt
new file mode 100755
index 0000000..54d6cd1
--- /dev/null
+++ b/src/stm32lib/examples/SDIO/readme.txt
@@ -0,0 +1,79 @@
+/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
+* File Name          : readme.txt
+* Author             : MCD Application Team
+* Version            : V2.0.1
+* Date               : 06/13/2008
+* Description        : Description of the SDIO Example.
+********************************************************************************
+* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
+* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
+* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
+* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
+* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+*******************************************************************************/
+
+Example description
+===================
+This example provides a basic example of how to use the SDIO firmware library and
+an associate driver to perform read/write operations on the SD Card memory 
+mounted on the STM3210E-EVAL board.
+Below is a description of the different example steps:
+  - Configure the SDIO according to the desired SDIO_CK clock frequency.
+  - Reset the SD Card
+  - Identify the SD Card
+  - Initializes the SD Card
+  - Get the SD Card Info
+  - Select the SD Card
+  - Enable the Wide Bus mode (4-bit data)
+  - Erase the correponding blocks
+  - Read the Erased blocks
+  - Test if the corresponding Blocks are well erased: check if the EraseStatus 
+    variable is equal to PASSED.
+  - Set the Data Transfer Mode to DMA   
+  - Write a single Block             
+  - Read a single Block
+  - Comapare the written Block and the read one: check if the TransferStatus1 
+    variable is equal to PASSED.
+  - Write multiple Blocks (2)             
+  - Read multiple Blocks (2)
+  - Comapare the written Blocks and the read one: check if the TransferStatus2 
+    variable is equal to PASSED.  
+
+
+Directory contents
+==================
+stm32f10x_conf.h  Library Configuration file
+stm32f10x_it.c    Interrupt handlers
+stm32f10x_it.h    Header for stm32f10x_it.c
+sdcard.c          SD Card Driver file
+sdcard.h          Header for sdcard.c
+main.c            Main program
+
+
+Hardware environment
+====================
+This example runs on STMicroelectronics STM3210E-EVAL evaluation board and can be
+easily tailored to any other hardware.
+
+Note: make sure that the Jumper 17 (JP17) is closed and Jumper 20 (JP20) is open
+      in STM3210E-EVAL 
+
+
+How to use it
+=============
+In order to make the program work, you must do the following:
+- Create a project and setup all your toolchain's start-up files
+- Compile the directory content files and required Library files:
+  + stm32f10x_lib.c
+  + stm32f10x_gpio.c
+  + stm32f10x_rcc.c
+  + stm32f10x_nvic.c
+  + stm32f10x_flash.c
+  + stm32f10x_sdio.c
+  + stm32f10x_dma.c
+  
+- Link all compiled files and load your image into either RAM or Flash
+- Run the example
+
+******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******