1 files changed, 0 insertions, 95 deletions
diff --git a/src/stm32lib/examples/PWR/STOP/readme.txt b/src/stm32lib/examples/PWR/STOP/readme.txt
deleted file mode 100755
index fa6bbb3..0000000
--- a/src/stm32lib/examples/PWR/STOP/readme.txt
+++ /dev/null
@@ -1,95 +0,0 @@
-/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
-* File Name          : readme.txt
-* Author             : MCD Application Team
-* Version            : V2.0.1
-* Date               : 06/13/2008
-* Description        : Description of the PWR STOP Example.
-********************************************************************************
-* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
-* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
-* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
-* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
-* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
-* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
-*******************************************************************************/
-
-Example description
-===================
-This example shows how to enter the system to STOP mode and wake-up using EXTI
-Line interrupts. The EXTI Line sources are PB.09/PG.08 and RTC Alarm.
-
-The EXTI line9/8 is configured to generate interrupt on falling edge.
-The EXTI line17(RTC Alarm) is configured to generate interrupt on rising edge and
-the RTC time base is set to 1 second using the external low speed oscillator(LSE).
-
-The system clock is set to 72 MHz using the external high speed oscillator(HSE).
-
-The system enters and exits STOP mode as following:
-After 2 second from system start-up, the RTC is configured to generate an Alarm
-event in 3 second then the system enters STOP mode. To wake-up from STOP mode you
-have to apply a rising edge on EXTI line9/8, otherwise the  RTC Alarm will wake-up
-the system within 3 second. After exit from STOP the system clock is reconfigured
-to its previous state (as HSE and PLL are disabled in STOP mode).
-Then after a delay the system will enter again in STOP mode and exit in the way
-described above. This behavior is repeated in an infinite loop.
-
-Four leds connected to GPIO_LED Pin6(LD1), Pin7(LD2) and Pin8(LD3) are used to
-monitor the system state as following:
- - LD1 on: system in RUN mode
- - LD1 off: system in STOP mode
- - LD2 is toggled if EXTI Line9/8 is used to exit from STOP 
- - LD3 is toggled if EXTI line17(RTC Alarm) is used to exit from STOP 
-
-
-Directory contents
-==================
-platform_config.h    Evaluation board specific configuration file
-stm32f10x_conf.h     Library Configuration file
-stm32f10x_it.c       Interrupt handlers
-stm32f10x_it.h       Header for stm32f10x_it.c
-main.c               Main program
-main.h               Header for main.c
-
-
-Hardware environment
-====================
-This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
-boards and can be easily tailored to any other hardware.
-To select the STMicroelectronics evaluation board used to run the example, uncomment
-the corresponding line in platform_config.h file.
-
- + STM3210B-EVAL 
-    - Use LD1, LD2 and LD3 leds connected respectively to PC.06, PC.07 and PC.08 pins
-    - Use the Key push-button connected to pin PB.09 (EXTI Line9).
-         
- + STM3210E-EVAL
-    - Use LD1, LD2 and LD3 leds connected respectively to PF.06, PF0.7 and PF.08 pins
-    - Use the Key push-button connected to pin PG.08 (EXTI Line8).
-
-   
-How to use it
-=============
-In order to make the program work, you must do the following :
-- Create a project and setup all your toolchain's start-up files
-- Compile the directory content files and required Library files :
-  + stm32f10x_nvic.c
-  + stm32f10x_rcc.c
-  + stm32f10x_lib.c
-  + stm32f10x_gpio.c
-  + stm32f10x_rtc.c  
-  + stm32f10x_pwr.c  
-  + stm32f10x_bkp.c
-  + stm32f10x_exti.c
-  + stm32f10x_flash.c
-  + stm32f10x_systick.c          
-   
-- Link all compiled files and load your image into target memory
-- Run the example in standalone mode (without debugger connection)
-
-NOTE: For power consumption measurement in STOP mode you have to: 
-1. Modify the example to configure all unused GPIO port pins in Analog Input mode
-   (floating input trigger OFF). Refer to GPIO\IOToggle example for more details. 
-2. Replace jumper JP9 in the STM3210B-EVAL board or JP12 in the STM3210E-EVAL
-   board by an ampermeter.
-
-******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******