1 files changed, 79 insertions, 0 deletions
diff --git a/src/stm32lib/examples/I2C/M24C08_EEPROM/readme.txt b/src/stm32lib/examples/I2C/M24C08_EEPROM/readme.txt
new file mode 100755
index 0000000..d1b9c50
--- /dev/null
+++ b/src/stm32lib/examples/I2C/M24C08_EEPROM/readme.txt
@@ -0,0 +1,79 @@
+/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
+* File Name          : readme.txt
+* Author             : MCD Application Team
+* Version            : V2.0.1
+* Date               : 06/13/2008
+* Description        : Description of the I2C and M24C08 EEPROM communication example.
+********************************************************************************
+* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
+* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
+* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
+* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
+* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+*******************************************************************************/
+
+Example description
+===================
+This example provides a basic example of how to use the I2C software library
+and an associate I2C EEPROM driver to communicate with an M24C08 EEPROM.
+I2C1 is configured in Master transmitter during write operation and in Master 
+receiver during read operation from I2C EEPROM. 
+The speed is set to the maximum frequency of 400kHz. This value is defined in 
+the I2c_ee.c file, which could be in the range of 0 to 400KHZ.
+One I2C EEPROM Block address where the program will write the buffer have to be
+selected from the four address available and defined in the I2c_ee.h file. 
+The EEPROM address where the program start the write and the read operations is
+defined in the main.c file. 
+
+First, the contents of Tx1_Buffer are written to the EEPROM_WriteAddress1 and the
+written data are read. The written and the read buffers data are then compared.
+Following the read operation, the program wait that the EEPROM reverts to its 
+Standby state. A second write operation is, then, performed and this time, Tx2_Buffer
+is written to EEPROM_WriteAddress2, which represents the address just after the last 
+written one in the first write. After completion of the second write operation, the 
+written data are read. The contents of the written and the read	buffers are compared. 
+
+
+Directory contents
+==================
+stm32f10x_conf.h  Library Configuration file
+stm32f10x_it.c    Interrupt handlers
+stm32f10x_it.h    Interrupt handlers header file
+main.c            Main program
+i2c_ee.c          I2C EEPROM driver
+i2c_ee.h          Header for the i2c_ee.c file
+
+
+Hardware environment
+====================
+This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
+boards with addition of the following hardware connection:
+   - Connect I2C1 SCL pin (PB.06) to I2C EEPROM SCL (pin6)
+   - Connect I2C1 SDA pin (PB.07) to I2C EEPROM SDA (pin5)
+   - Check that a pull-up resistor is connected on one I2C SDA pin
+   - Check that a pull-up resistor is connected on one I2C SCL pin
+   - Connect I2C EEPROM Vcc (pin8) to Vdd
+   - Connect I2C EEPROM Vss (pin4) to Vss
+
+Note: The pull-up resitors are already implemented on the STM3210B-EVAL and
+      STM3210E-EVAL evaluation boards.
+
+
+How to use it
+=============
+In order to make the program work, you must do the following :
+- Create a project and setup all your toolchain's start-up files
+- Compile the directory content files and required Library files :
+  + stm32f10x_lib.c
+  + stm32f10x_i2c.c
+  + stm32f10x_rcc.c
+  + stm32f10x_nvic.c
+  + stm32f10x_gpio.c
+  + stm32f10x_flash.c
+    
+- Link all compiled files and load your image into target memory
+- Run the example
+
+
+******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******