1 files changed, 75 insertions, 0 deletions
diff --git a/src/stm32lib/examples/I2C/DualAddress/readme.txt b/src/stm32lib/examples/I2C/DualAddress/readme.txt
new file mode 100755
index 0000000..d192246
--- /dev/null
+++ b/src/stm32lib/examples/I2C/DualAddress/readme.txt
@@ -0,0 +1,75 @@
+/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
+* File Name          : readme.txt
+* Author             : MCD Application Team
+* Version            : V2.0.1
+* Date               : 06/13/2008
+* Description        : Description of the I2C dual addressng mode example.
+********************************************************************************
+* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
+* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
+* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
+* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
+* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+*******************************************************************************/
+
+Example description
+===================
+This example provides a description of how to transfer two data buffer from I2C1
+to I2C2 using its both addresses in the same application.
+
+The example consist in two parts:
+1. First step, the I2C1 master transmitter sends the Tx_Buffer1 data buffer to the 
+   slave I2C2 which saves the received data in Rx_Buffer1. I2C2 is addressed in 
+   this case by its first slave address I2C2_SLAVE1_ADDRESS7 programmed in the
+   I2C2 OAR1 register.
+   The transmitted and received buffers are compared to check that all data
+   have been correctly transferred.
+2. Second step, the I2C2 is now addressed by its second slave address
+   I2C2_SLAVE2_ADDRESS7 programmed in the I2C2 OAR2 register. The Tx_Buffer2
+   contents are transmitted by the master I2C1 to the slave I2C2 which stores
+   them into Rx_Buffer2.
+   A second comparison takes place between the transmitted and received buffers.
+
+The communication clock speed is set to 200KHz.
+
+
+Directory contents
+==================
+stm32f10x_conf.h  Library Configuration file
+stm32f10x_it.c    Interrupt handlers
+stm32f10x_it.h    Interrupt handlers header file
+main.c            Main program
+
+
+Hardware environment
+====================
+This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
+boards and can be easily tailored to any other hardware.
+
+ - Connect I2C1 SCL pin (PB.06) to I2C2 SCL pin (PB.10)
+ - Connect I2C1 SDA pin (PB.07) to I2C2 SDA pin	(PB.11)
+ - Check that a pull-up resistor is connected on one I2C SDA pin
+ - Check that a pull-up resistor is connected on one I2C SCL pin
+
+Note: The pull-up resitors are already implemented on the STM3210B-EVAL and
+      STM3210E-EVAL evaluation boards.
+     
+
+How to use it
+=============
+In order to make the program work, you must do the following :
+- Create a project and setup all your toolchain's start-up files
+- Compile the directory content files and required Library files :
+  + stm32f10x_lib.c
+  + stm32f10x_i2c.c
+  + stm32f10x_rcc.c
+  + stm32f10x_gpio.c
+  + stm32f10x_nvic.c
+  + stm32f10x_flash.c
+    
+- Link all compiled files and load your image into target memory
+- Run the example
+
+
+******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******