1 files changed, 69 insertions, 0 deletions
diff --git a/src/stm32lib/examples/I2C/10bitAddress/readme.txt b/src/stm32lib/examples/I2C/10bitAddress/readme.txt
new file mode 100755
index 0000000..a14775f
--- /dev/null
+++ b/src/stm32lib/examples/I2C/10bitAddress/readme.txt
@@ -0,0 +1,69 @@
+/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
+* File Name          : readme.txt
+* Author             : MCD Application Team
+* Version            : V2.0.1
+* Date               : 06/13/2008
+* Description        : Description of the I2C 10bit addressing mode example.
+********************************************************************************
+* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
+* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
+* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
+* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
+* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+*******************************************************************************/
+
+Example description
+===================
+This example provides a description of how to transfer a data buffer from I2C1 to
+I2C2 in 10-bit addressing mode.
+
+After enabling the two I2C peripherals, the transfer in 10-bit addressing mode
+starts after the I2C1 start condition is generated. Each time an event occurs on
+the master or the slave, it is managed on I2C1 or I2C2, respectively.
+In this application, Tx_Buffer is transmitted from the master I2C1 to the slave
+I2C2 and stored into Rx_Buffer. The transmitted and received buffers are compared
+to check that all data have been correctly transferred.
+
+The communication clock speed is set to 300KHz.
+
+
+Directory contents
+==================
+stm32f10x_conf.h  Library Configuration file
+stm32f10x_it.c    Interrupt handlers
+stm32f10x_it.h    Interrupt handlers header file
+main.c            Main program
+
+
+Hardware environment
+====================
+This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
+boards and can be easily tailored to any other hardware.
+
+ - Connect I2C1 SCL pin (PB.06) to I2C2 SCL pin (PB.10)
+ - Connect I2C1 SDA pin (PB.07) to I2C2 SDA pin	(PB.11)
+ - Check that a pull-up resistor is connected on one I2C SDA pin
+ - Check that a pull-up resistor is connected on one I2C SCL pin
+
+Note: The pull-up resitors are already implemented on the STM3210B-EVAL and
+      STM3210E-EVAL evaluation boards. 
+
+
+How to use it
+=============
+In order to make the program work, you must do the following :
+- Create a project and setup all your toolchain's start-up files
+- Compile the directory content files and required Library files:
+  + stm32f10x_lib.c
+  + stm32f10x_i2c.c
+  + stm32f10x_rcc.c
+  + stm32f10x_nvic.c
+  + stm32f10x_gpio.c
+  + stm32f10x_flash.c
+  
+- Link all compiled files and load your image into target memory
+- Run the example
+
+
+******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******