1 files changed, 73 insertions, 0 deletions
diff --git a/src/stm32lib/examples/GPIO/JTAG_Remap/readme.txt b/src/stm32lib/examples/GPIO/JTAG_Remap/readme.txt
new file mode 100755
index 0000000..2393f16
--- /dev/null
+++ b/src/stm32lib/examples/GPIO/JTAG_Remap/readme.txt
@@ -0,0 +1,73 @@
+/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
+* File Name          : readme.txt
+* Author             : MCD Application Team
+* Version            : V2.0.1
+* Date               : 06/13/2008
+* Description        : Description of the GPIO JTAG Remap Example.
+********************************************************************************
+* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
+* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
+* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
+* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
+* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+*******************************************************************************/
+
+Example description
+===================
+This example provides a short description of how to use the JTAG IOs as standard 
+GPIOs and gives a configuration sequence. 
+
+First, the SWJ-DP is disabled. The SWJ-DP pins are configured as output push-pull.
+Five LEDs connected to the PA.13(JTMS/SWDAT), PA.14(JTCK/SWCLK), PA.15(JTDI), 
+PB.03(JTDO) and PB.04(JTRST) pins are toggled in an infinite loop.
+
+Note that once the JTAG IOs are disabled, the connection with the host debugger is
+lost and cannot be re-established as long as the JTAG IOs remain disabled. 
+To avoid this situation, a specified pin is connected to a push-button that is used
+to disable or not the JTAG IOs:
+ 1. push-button pressed at reset: JTAG IOs disabled
+ 2. push-button not pressed at reset: JTAG IOs unchanged
+
+
+Directory contents
+==================
+platform_config.h    Evaluation board specific configuration file
+stm32f10x_conf.h     Library Configuration file
+stm32f10x_it.c       Interrupt handlers
+stm32f10x_it.h       Header for stm32f10x_it.c
+main.c               Main program
+
+
+Hardware environment
+====================
+This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
+boards and can be easily tailored to any other hardware.
+To select the STMicroelectronics evaluation board used to run the example, uncomment
+the corresponding line in platform_config.h file.
+
+ + STM3210B-EVAL 
+    - Connect five leds to pins PA.13, PA.14, PA.15, PB.03 and PB.04. 
+    - Use the Key push-button connected to pin PB.09 (EXTI Line9).
+ 
+ + STM3210E-EVAL
+    - Connect five leds to pins PA.13, PA.14, PA.15, PB.03 and PB.04. 
+    - Use the Key push-button connectedto pin PG.08 (EXTI Line8).
+
+      
+How to use it
+=============
+In order to make the program work, you must do the following:
+- Create a project and setup all your toolchain's start-up files
+- Compile the directory content files and required Library files:
+  + stm32f10x_lib.c
+  + stm32f10x_gpio.c
+  + stm32f10x_rcc.c
+  + stm32f10x_nvic.c
+  + stm32f10x_flash.c
+    
+- Link all compiled files and load your image into target memory
+- Run the example
+
+
+******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******