1 files changed, 67 insertions, 0 deletions
diff --git a/src/stm32lib/examples/DMA/I2C_RAM/readme.txt b/src/stm32lib/examples/DMA/I2C_RAM/readme.txt
new file mode 100755
index 0000000..926e8c1
--- /dev/null
+++ b/src/stm32lib/examples/DMA/I2C_RAM/readme.txt
@@ -0,0 +1,67 @@
+/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
+* File Name          : readme.txt
+* Author             : MCD Application Team
+* Version            : V2.0.1
+* Date               : 06/13/2008
+* Description        : Description of the DMA I2C example.
+********************************************************************************
+* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
+* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
+* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
+* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
+* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+*******************************************************************************/
+
+Example description
+===================
+This example provides a description of how to use two DMA channels to transfer a 
+data buffer from memory to I2C2 through I2C1.
+I2C1 is set as the master transmitter and I2C2 as the slave receiver. DMA1 Channel5 is
+configured to store the data received from I2C2 into the Rx buffer (reception buffer).
+DMA1 Channel6 is configured to transfer data from the Tx buffer (transmission buffer) to
+the I2C1 DR register. After the generation of the Start condition and once the slave
+address has been acknowledged, DMA capability is enabled for both I2C1 and I2C2. As soon as the
+two I2C DMAEN bits are set in the I2C1_CR2 and I2C2_CR2 registers, the transmission of
+the Tx buffer is started by DMA1 Channel5 and at the same time the data received on
+I2C2 is stored in Rx buffer using DMA1 Channel6 . The transmitted and the received buffers
+are compared to check that all data have been correctly transferred.
+
+
+Directory contents
+==================
+stm32f10x_conf.h  Library Configuration file
+stm32f10x_it.c    Interrupt handlers
+stm32f10x_it.h    Interrupt handlers header file
+main.c            Main program
+
+
+Hardware environment
+====================
+This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
+boards and can be easily tailored to any other hardware.
+
+ - Connect I2C1 SCL pin (PB.06) to I2C2 SCL pin (PB.10)
+ - Connect I2C1 SDA pin (PB.07) to I2C2 SDA pin	(PB.11)
+ - Check that a pull-up resistor is connected on one I2C SDA pin
+ - Check that a pull-up resistor is connected on one I2C SCL pin
+      
+
+How to use it
+=============
+In order to make the program work, you must do the following :
+- Create a project and setup all your toolchain's start-up files
+- Compile the directory content files and required Library files :
+  + stm32f10x_lib.c
+  + stm32f10x_dma.c
+  + stm32f10x_rcc.c
+  + stm32f10x_i2c.c
+  + stm32f10x_nvic.c
+  + stm32f10x_gpio.c
+  + stm32f10x_flash.c
+    
+- Link all compiled files and load your image into target memory
+- Run the example
+
+
+******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******