diff options
Diffstat (limited to 'src/stm32lib/examples/CAN/readme.txt')
-rwxr-xr-x | src/stm32lib/examples/CAN/readme.txt | 69 |
1 files changed, 69 insertions, 0 deletions
diff --git a/src/stm32lib/examples/CAN/readme.txt b/src/stm32lib/examples/CAN/readme.txt new file mode 100755 index 0000000..27a02a6 --- /dev/null +++ b/src/stm32lib/examples/CAN/readme.txt @@ -0,0 +1,69 @@ +/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
+* File Name : readme.txt
+* Author : MCD Application Team
+* Version : V2.0.1
+* Date : 06/13/2008
+* Description : Description of the CAN example.
+********************************************************************************
+* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
+* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
+* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
+* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
+* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+*******************************************************************************/
+
+Example description
+===================
+This example provides a description of how to set a communication with the bxCAN
+in loopback mode.
+
+The CAN cell first performs a transmission and a reception of a standard data
+frame by polling at 100 Kbits/s. The received frame is checked and some LEDs light
+up to indicate whether the communication was successful. Then, an extended data
+frame is transmitted at 500 Kbits/s. Reception is done in the interrupt handler
+when the message becomes pending in the FIFO. Finally, the LEDs indicate if both
+transmission and reception have been successful.
+
+
+Directory contents
+==================
+platform_config.h Hardware configuration header file
+stm32f10x_conf.h Library Configuration file
+stm32f10x_it.c Interrupt handlers
+stm32f10x_it.h Interrupt handlers header file
+main.c Main program
+
+
+Hardware environment
+====================
+This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
+boards and can be easily tailored to any other hardware.
+To select the STMicroelectronics evaluation board used to run the example, uncomment
+the corresponding line in platform_config.h file.
+
+ + STM3210B-EVAL
+ - Use LD1, LD2, LD3 and LD4 leds connected respectively to PC.06, PC.07, PC.08
+ and PC.09 pins
+
+ + STM3210E-EVAL
+ - Use LD1, LD2, LD3 and LD4 leds connected respectively to PF.06, PF0.7, PF.08
+ and PF.09 pins
+
+
+How to use it
+=============
+In order to make the program work, you must do the following :
+- Create a project and setup all your toolchain's start-up files
+- Compile the directory content files and required Library files :
+ + stm32f10x_lib.c
+ + stm32f10x_can.c
+ + stm32f10x_rcc.c
+ + stm32f10x_gpio.c
+ + stm32f10x_nvic.c
+ + stm32f10x_flash.c
+
+- Link all compiled files and load your image into target memory
+- Run the example
+
+******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******
|