1 files changed, 71 insertions, 0 deletions
diff --git a/src/stm32lib/examples/ADC/RegSimul_DualMode/readme.txt b/src/stm32lib/examples/ADC/RegSimul_DualMode/readme.txt
new file mode 100755
index 0000000..ded3195
--- /dev/null
+++ b/src/stm32lib/examples/ADC/RegSimul_DualMode/readme.txt
@@ -0,0 +1,71 @@
+/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
+* File Name          : readme.txt
+* Author             : MCD Application Team
+* Version            : V2.0.1
+* Date               : 06/13/2008
+* Description        : Description of the ADC regular simultaneous dual mode Example.
+********************************************************************************
+* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
+* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
+* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
+* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
+* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+*******************************************************************************/
+
+Example description
+===================
+This example describes how to use ADC1 and ADC2 in regular simultaneous dual mode.
+ADC1 is configured to convert channel14 and channel17 regular channels continuously.
+ADC2 is configured to convert channel11 and channel12 regular channels continuously.
+The connection between internal Vref and channel17 is enabled for ADC1.
+
+Once the regular channels conversion is started by software, channel14 is converted
+on ADC1 and channel11 is converted on ADC2 on the same time. The 32bits conversion 
+result is then stored on ADC1 DR register. The DMA will transfer this data which
+will be stored ADC_DualConvertedValueTab table. Consecutively to those conversion,
+channel17 is converted on ADC1 and channel12 on ADC2. The combined conversion
+result is also transfered by DMA to the same destination buffer. 
+
+The same procedure is repeated until the specified number of data to be transfered
+by DMA is reached.
+
+The ADC1 clock is set to 14 MHz.
+
+
+Directory contents
+==================
+stm32f10x_conf.h  Library Configuration file
+stm32f10x_it.c    Interrupt handlers
+stm32f10x_it.h    Interrupt handlers header file
+main.c            Main program
+
+
+Hardware environment
+====================
+This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
+boards and can be easily tailored to any other hardware.
+
+ - Connect a known voltage, between 0-3.3V, to ADC Channel14 mapped on pin PC.04
+   (potentiometer RV1 on STM3210B-EVAL and STM3210E-EVAL boards),ADC Channel11 mapped 
+   on pin PC.01 and ADC Channel12 mapped on pin PC.02.
+   
+      
+How to use it
+=============
+In order to make the program work, you must do the following :
+- Create a project and setup all your toolchain's start-up files
+- Compile the directory content files and required Library files :
+  + stm32f10x_lib.c
+  + stm32f10x_adc.c
+  + stm32f10x_dma.c
+  + stm32f10x_gpio.c
+  + stm32f10x_rcc.c
+  + stm32f10x_nvic.c
+  + stm32f10x_flash.c
+    
+- Link all compiled files and load your image into target memory
+- Run the example
+
+
+******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******