1 files changed, 0 insertions, 73 deletions
diff --git a/src/stm32lib/examples/ADC/AnalogWatchdog/readme.txt b/src/stm32lib/examples/ADC/AnalogWatchdog/readme.txt
deleted file mode 100755
index c550b53..0000000
--- a/src/stm32lib/examples/ADC/AnalogWatchdog/readme.txt
+++ /dev/null
@@ -1,73 +0,0 @@
-/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
-* File Name          : readme.txt
-* Author             : MCD Application Team
-* Version            : V2.0.1
-* Date               : 06/13/2008
-* Description        : Description of the ADC analog watchdog example.
-********************************************************************************
-* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
-* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
-* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
-* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
-* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
-* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
-*******************************************************************************/
-
-Example description
-===================
-This example describes how to use the ADC analog watchdog to guard continuously  
-an ADC channel.
-The ADC1 is configured to convert continuously ADC channel14. The analog watchdog
-is configured and enabled to guard a single regular channel. 
-Each time the channel14 converted value exceed programmed analog watchdog high 
-threshold (value 0x0B00) or goes down analog watchdog low threshold (value 0x0300)
-an AWD interrupt is generated and the output pin connected to LED1 is toggled. The
-LED will bright as long as the AWD interrupt is generated which means that the 
-converted value of regular ADC channel14 is outside the range limited by high and 
-low analog watchdog thresholds.
-The ADC1 clock is set to 14 MHz.
-
-
-Directory contents
-==================
-platform_config.h  Evaluation board specific configuration file
-stm32f10x_conf.h   Library Configuration file
-stm32f10x_it.c     Interrupt handlers
-stm32f10x_it.h     Interrupt handlers header file
-main.c             Main program
-
-
-Hardware environment
-====================
-This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
-boards and can be easily tailored to any other hardware.
-To select the STMicroelectronics evaluation board used to run the example, uncomment
-the corresponding line in platform_config.h file.
-
- + STM3210B-EVAL 
-    - Use LD1 led connected to PC.06 pin
- 
- + STM3210E-EVAL
-    - Use LD1 led connected to PF.06 pin
-
- - Connect a variable power supply 0-3.3V to ADC Channel14 mapped on pin PC.04
-   (potentiometer RV1 on STM3210B-EVAL and STM3210E-EVAL boards) 
-
-         
-How to use it
-=============
-In order to make the program work, you must do the following :
-- Create a project and setup all your toolchain's start-up files
-- Compile the directory content files and required Library files :
-  + stm32f10x_lib.c
-  + stm32f10x_adc.c
-  + stm32f10x_gpio.c
-  + stm32f10x_rcc.c
-  + stm32f10x_nvic.c
-  + stm32f10x_flash.c
-    
-- Link all compiled files and load your image into target memory
-- Run the example
-
-
-******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******