1 files changed, 73 insertions, 0 deletions
diff --git a/src/stm32lib/examples/ADC/AnalogWatchdog/readme.txt b/src/stm32lib/examples/ADC/AnalogWatchdog/readme.txt
new file mode 100755
index 0000000..c550b53
--- /dev/null
+++ b/src/stm32lib/examples/ADC/AnalogWatchdog/readme.txt
@@ -0,0 +1,73 @@
+/******************** (C) COPYRIGHT 2008 STMicroelectronics ********************
+* File Name          : readme.txt
+* Author             : MCD Application Team
+* Version            : V2.0.1
+* Date               : 06/13/2008
+* Description        : Description of the ADC analog watchdog example.
+********************************************************************************
+* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
+* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
+* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
+* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
+* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+*******************************************************************************/
+
+Example description
+===================
+This example describes how to use the ADC analog watchdog to guard continuously  
+an ADC channel.
+The ADC1 is configured to convert continuously ADC channel14. The analog watchdog
+is configured and enabled to guard a single regular channel. 
+Each time the channel14 converted value exceed programmed analog watchdog high 
+threshold (value 0x0B00) or goes down analog watchdog low threshold (value 0x0300)
+an AWD interrupt is generated and the output pin connected to LED1 is toggled. The
+LED will bright as long as the AWD interrupt is generated which means that the 
+converted value of regular ADC channel14 is outside the range limited by high and 
+low analog watchdog thresholds.
+The ADC1 clock is set to 14 MHz.
+
+
+Directory contents
+==================
+platform_config.h  Evaluation board specific configuration file
+stm32f10x_conf.h   Library Configuration file
+stm32f10x_it.c     Interrupt handlers
+stm32f10x_it.h     Interrupt handlers header file
+main.c             Main program
+
+
+Hardware environment
+====================
+This example runs on STMicroelectronics STM3210B-EVAL and STM3210E-EVAL evaluation
+boards and can be easily tailored to any other hardware.
+To select the STMicroelectronics evaluation board used to run the example, uncomment
+the corresponding line in platform_config.h file.
+
+ + STM3210B-EVAL 
+    - Use LD1 led connected to PC.06 pin
+ 
+ + STM3210E-EVAL
+    - Use LD1 led connected to PF.06 pin
+
+ - Connect a variable power supply 0-3.3V to ADC Channel14 mapped on pin PC.04
+   (potentiometer RV1 on STM3210B-EVAL and STM3210E-EVAL boards) 
+
+         
+How to use it
+=============
+In order to make the program work, you must do the following :
+- Create a project and setup all your toolchain's start-up files
+- Compile the directory content files and required Library files :
+  + stm32f10x_lib.c
+  + stm32f10x_adc.c
+  + stm32f10x_gpio.c
+  + stm32f10x_rcc.c
+  + stm32f10x_nvic.c
+  + stm32f10x_flash.c
+    
+- Link all compiled files and load your image into target memory
+- Run the example
+
+
+******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE******