aboutsummaryrefslogtreecommitdiffstats
path: root/source
diff options
context:
space:
mode:
Diffstat (limited to 'source')
-rw-r--r--source/hardware/maple-native-beta.rst559
-rw-r--r--source/index.rst3
2 files changed, 561 insertions, 1 deletions
diff --git a/source/hardware/maple-native-beta.rst b/source/hardware/maple-native-beta.rst
new file mode 100644
index 0000000..8b1dc45
--- /dev/null
+++ b/source/hardware/maple-native-beta.rst
@@ -0,0 +1,559 @@
+.. highlight:: sh
+
+.. _maple-native:
+
+Maple Native β
+==============
+
+This page is a general resource for information specific to the Maple
+Native Beta. Since this is a beta release, the information here may
+change slightly between now and the final Maple Native release.
+
+.. contents:: Contents
+ :local:
+
+Technical Specifications
+------------------------
+
+.. TODO [0.0.12] Verify recommended input voltage
+
+* MCU: `STM32F103ZET6 <maple-native-b-stdocs>`_, a 32-bit ARM Cortex M3
+ microprocessor.
+* Clock Speed: **72 MHz**
+* **512 KB Flash**, **64 KB SRAM** (on-chip), **1 MB SRAM** (external)
+* 106 :ref:`digital I/O pins <gpio>`
+* 17 :ref:`PWM <pwm>` pins at 16 bit resolution
+* 21 :ref:`analog input (ADC) <adc>` pins at 12-bit resolution
+* 3 :ref:`SPI <spi>` peripherals
+* 2 :ref:`I2C <i2c>` peripherals
+* 12 Channels of Direct Memory Access (**DMA**) (:ref:`libmaple-dma`)
+ with 2 DMA controllers
+* 3 :ref:`USART (serial port) <usart>` peripherals, 2 **UART** peripherals
+* 2 advanced, 4 general-purpose, and 2 basic :ref:`timers <timers>`
+* Dedicated :ref:`USB <usb>` port for programming and communications
+* :ref:`JTAG <jtag>`
+* Nested Vectored Interrupt Controller (NVIC) (including
+ :ref:`external interrupt <lang-attachinterrupt>` on GPIOs)
+* Supplies up to 500 mA at 3.3 V, with :ref:`separate 250 mA digital
+ and analog regulators <maple-native-b-adc-bank>` for low-noise analog
+ performance
+* :ref:`Open-source, four layer design <maple-native-b-hardware>`
+* Support for low power, sleep, and standby modes (<500 μA)
+* Operating Voltage: 3.3 V
+* Input Voltage (recommended): 3 V — 12 V
+* Dimensions: 4″ × 2.1″
+
+.. _maple-native-b-powering:
+
+Powering the Maple Native
+-------------------------
+
+The Maple Native may be powered from the barrel jack connector, USB,
+or a LiPo battery. The power source is determined by the header
+labeled "PWRSEL" on the silkscreen. Boards are shipped with a jumper
+on the USB selector. In order to power it off of an alternative
+source, unplug the Maple Native, then move the jumper to the desired
+selector before reconnecting power.
+
+You can also power the Maple Native via the pin labeled "Vin" on the
+vertical header to the right of the PWRSEL header. This pin feeds
+into both the digital and analog voltage regulators. However, don't
+do this while simultaneously powering the board from another source,
+or you could damage it.
+
+We recommend an input voltage no greater than 12 V.
+
+Using the Built-in Battery Charger
+----------------------------------
+
+Maple Native includes a built-in LiPo battery charger. In order to
+use it, put a jumper across the CHRG selector on the PWRSEL header and
+across the USB, or EXT selectors, depending on whether you're charging
+the battery via USB cable or Vin, respectively. The LED labeled CHRG
+will light up while the battery is being charged. When the battery is
+finished charging, the LED labeled DONE will light up.
+
+.. _maple-native-b-gpios:
+
+GPIO Information
+----------------
+
+The Maple Native features 106 total input/output pins, numbered ``D0``
+through ``D105``. In most cases, these numbers correspond to the
+numeric values next to each header on the Maple Native's silkscreen.
+However, pins ``D101`` through ``D105`` are broken out to the
+:ref:`JTAG <jtag>` header, and are not numbered on the silkscreen. In
+addition, some other pins have other uses by default [#fusedpins]_.
+
+.. _maple-native-b-but:
+
+Pin ``D6`` is the Native's :ref:`button pin <lang-board-values-but>`.
+It is thus mainly useful as an :ref:`input <lang-pin-levels>`. The
+pin will :ref:`read <lang-digitalread>` ``HIGH`` when the :ref:`button
+is pressed <lang-isbuttonpressed>`.
+
+.. _maple-native-b-led:
+
+Pin ``D22`` is the Native's :ref:`LED pin <lang-board-values-led>`.
+It is thus mainly useful as an :ref:`output <lang-pin-levels>`. The
+LED will glow when ``HIGH`` is :ref:`written <lang-digitalwrite>` to
+it.
+
+.. _maple-native-b-fsmc:
+
+.. FIXME [0.0.12] Add note on Native "use SRAM" vs. "no SRAM" builds
+..
+.. TODO [0.0.12] Specify which pins are safe, and which aren't
+
+Many of the pins on the right header (pins ``D56`` through ``D100``,
+the header is labeled "FSMC" on the silkscreen) are connected to
+:ref:`FSMC <fsmc>` lines. Using these pins as GPIOs may render the
+memory chip useless, which can cause your program to crash. For this
+reason, we don't recommend that you use these pins unless you know
+what you are doing.
+
+.. _maple-native-b-jtag:
+
+Pins ``D101`` through ``D105`` are connected to the pads on the
+:ref:`JTAG <jtag>` header. In order to use them as GPIOs, you must
+first disable the Maple Native's debug ports. You can do this by
+calling :ref:`lang-disabledebugports`. (Note that this means you
+won't be able to use JTAG or SW-Debug to debug your program).
+
+.. TODO [0.1.0] silkscreen pictures
+
+.. _maple-native-b-pin-map-master:
+
+Master Pin Map
+^^^^^^^^^^^^^^
+
+This table shows a summary the available functionality on every GPIO
+pin, by peripheral type. The "5 V?" column documents whether or not
+the pin is :ref:`5 volt tolerant <gpio-5v-tolerant>`.
+
+Note that this table is not exhaustive; on some pins, more peripherals
+are available than are listed here.
+
+**Top header:**
+
+.. csv-table::
+ :header: Pin, :ref:`GPIO <gpio>`, :ref:`ADC <adc>`, :ref:`Timer <timers>`, :ref:`I2C <i2c>`, :ref:`UART <usart>`, :ref:`SPI <spi>`, 5 V?
+
+ D0, PB10, -, -, 2_SCL, 3_TX, -, Yes
+ D1, PB11, -, -, 2_SDA, 3_RX, -, Yes
+ D2, PB12, -, 1_BKIN, 2_SMBA, 3_CK, 2_NSS, Yes
+ D3, PB13, -, -, -, 3_CTS, 2_SCK, Yes
+ D4, PB14, -, -, -, 3_RTS, 2_MISO, Yes
+ D5, PB15, -, -, -, -, 2_MOSI, Yes
+ D6, PG15, -, -, -, -, -, Yes
+ D7, PC0, 1_CH10, -, -, -, -, -
+ D8, PC1, 1_CH11, -, -, -, -, -
+ D9, PC2, 1_CH12, -, -, -, -, -
+ D10, PC3, 1_CH13, -, -, -, -, -
+ D11, PC4, 1_CH14, -, -, -, -, -
+ D12, PC5, 1_CH15, -, -, -, -, -
+ D13, PC6, -, 8_CH1, -, -, -, Yes
+ D14, PC7, -, 8_CH2, -, -, -, Yes
+ D15, PC8, -, 8_CH3, -, -, -, Yes
+ D16, PC9, -, 8_CH4, -, -, -, Yes
+ D17, PC10, -, -, -, 4_TX, -, Yes
+ D18, PC11, -, -, -, 4_RX, -, Yes
+ D19, PC12, -, -, -, 5_TX, -, Yes
+ D20, PC13, -, -, -, -, -, -
+ D21, PC14, -, -, -, -, -, -
+ D22, PC15, -, -, -, -, -, -
+ D23, PA8, -, 1_CH1, -, 1_CK, -, Yes
+ D24, PA9, -, 1_CH2, -, 1_TX, -, Yes
+ D25, PA10, -, 1_CH3, -, 1_RX, -, Yes
+ D26, PB9, -, 4_CH4, -, -, -, Yes
+
+**Bottom header:**
+
+.. note:: ``D48``, ``D49``, ``D50``, ``D51`` are also connected to
+ Timer 2 channels 1, 2, 3, and 4, respectively.
+
+.. csv-table::
+ :header: Pin, :ref:`GPIO <gpio>`, :ref:`ADC <adc>`, :ref:`Timer <timers>`, :ref:`I2C <i2c>`, :ref:`UART <usart>`, :ref:`SPI <spi>`, 5 V?
+
+ D27, PD2, -, 3_ETR, -, 5_RX, -, Yes
+ D28, PD3, -, -, -, -, -, Yes
+ D29, PD6, -, -, -, -, -, Yes
+ D30, PG11, -, -, -, -, -, Yes
+ D31, PG12, -, -, -, -, -, Yes
+ D32, PG13, -, -, -, -, -, Yes
+ D33, PG14, -, -, -, -, -, Yes
+ D34, PG8, -, -, -, -, -, Yes
+ D35, PG7, -, -, -, -, -, Yes
+ D36, PG6, -, -, -, -, -, Yes
+ D37, PB5, -, -, 1_SMBA, -, 3_MOSI, -
+ D38, PB6, -, 4_CH1, 1_SCL, -, -, Yes
+ D39, PB7, -, 4_CH2, 1_SDA, -, -, Yes
+ D40, PF11, -, -, -, -, -, Yes
+ D41, PF6, 3_CH4, -, -, -, -, -
+ D42, PF7, 3_CH5, -, -, -, -, -
+ D43, PF8, 3_CH6, -, -, -, -, -
+ D44, PF9, 3_CH7, -, -, -, -, -
+ D45, PF10, 3_CH8, -, -, -, -, -
+ D46, PB1, 1_CH9, 3_CH4, -, -, -, -
+ D47, PB0, 1_CH8, 3_CH3, -, -, -, -
+ D48, PA0, 1_CH0, 5_CH1, -, 2_CTS, -, -
+ D49, PA1, 1_CH1, 5_CH2, -, 2_RTS, -, -
+ D50, PA2, 1_CH2, 5_CH3, -, 2_TX, -, -
+ D51, PA3, 1_CH3, 5_CH4, -, 2_RX, -, -
+ D52, PA4, 1_CH4, -, -, 2_CK, 1_NSS, -
+ D53, PA5, 1_CH5, -, -, -, 1_SCK, -
+ D54, PA6, 1_CH6, 3_CH1, -, -, 1_MISO, -
+ D55, PA7, 1_CH7, 3_CH2, -, -, 1_MOSI, -
+
+.. _maple-native-b-fsmc-map:
+
+**Right (FSMC) header**
+
+All of the following pins are 5V-tolerant. Note that in the "FSMC"
+column below, entries with a "Dn" value (D0, D1, etc.) don't refer to
+pins; they refer to FSMC data lines. See :ref:`RM0008
+<maple-native-b-stdocs>` for more information.
+
+.. warning:: Many of the pins on this header are used by the Maple
+ Native's SRAM chip. Don't use them as GPIOs unless you know what
+ you're doing, or your program may crash. :ref:`See above
+ <maple-native-b-fsmc>` for more information.
+
+.. csv-table::
+ :header: Pin, :ref:`GPIO <gpio>`, :ref:`FSMC <fsmc>`
+
+ D56, PF0, A0
+ D57, PD11, A16
+ D58, P14, D0
+ D59, PF1, A1
+ D60, PD12, A17
+ D61, PD15, D1
+ D62, PF2, A2
+ D63, PD13, A18
+ D64, PD0, D2
+ D65, PF3, A3
+ D66, PE3, A19
+ D67, PD1, D3
+ D68, PF4, A4
+ D69, PE4, A20
+ D70, PE7, D4
+ D71, PF5, A5
+ D72, PE5, A21
+ D73, PE8, D8
+ D74, PF12, A6
+ D75, PE6, A22
+ D76, PE9, D6
+ D77, PF13, A7
+ D78, PE10, D7
+ D79, PF14, A8
+ D80, PG9, NE2/NCE3
+ D81, PE11, D8
+ D82, PF15, A9
+ D83, PG10, NCE4_1/NE3/NCE4_2
+ D84, PE12, D9
+ D85, PG0, A10
+ D86, PD5, NWE
+ D87, PE13, D10
+ D88, PG1, A11
+ D89, PD4, NOE
+ D90, PE14, D11
+ D91, PG2, A12
+ D92, PE1, NBL1
+ D93, PE15, D12
+ D94, PG3, A13
+ D95, PE0, NBL0
+ D96, PD8, D13
+ D97, PG4, A14
+ D98, PD9, D14
+ D99, PG5, A15
+ D100, PD10, D15
+
+**JTAG header pins**
+
+.. note:: See :ref:`above <maple-native-b-jtag>` for more information on
+ these pins.
+
+.. csv-table::
+ :header: Pin, :ref:`GPIO <gpio>`, :ref:`SPI <spi>`, 5 V?
+
+ D101, PA13, -, Yes
+ D102, PA14, -, Yes
+ D103, PA15, 3_NSS, Yes
+ D104, PB3, 3_SCK, Yes
+ D105, PB4, 3_MISO, Yes
+
+.. _maple-native-b-gpio-port-map:
+
+GPIO Port Pin Map
+^^^^^^^^^^^^^^^^^
+
+The following tables show what pins are associated with each
+:ref:`GPIO port <gpio-ports>`.
+
+.. csv-table::
+ :header: GPIOA, GPIOB, GPIOC, GPIOD
+
+ PA0: D48, PB0: D47, PC0: D7, PD0: D64
+ PA1: D49, PB1: D46, PC1: D8, PD1: D67
+ PA2: D50, PB2: -, PC2: D9, PD2: D27
+ PA3: D51, PB3: D104, PC3: D10, PD3: D28
+ PA4: D52, PB4: D105, PC4: D11, PD4: D89
+ PA5: D53, PB5: D37, PC5: D12, PD5: D86
+ PA6: D54, PB6: D38, PC6: D13, PD6: D29
+ PA7: D55, PB7: D39, PC7: D14, PD7: -
+ PA8: D23, PB8: -, PC8: D15, PD8: D96
+ PA9: D24, PB9: D26, PC9: D16, PD9: D98
+ PA10: D25, PB10: D0, PC10: D17, PD10: D100
+ PA11: -, PB11: D1, PC11: D18, PD11: D57
+ PA12: -, PB12: D2, PC12: D19, PD12: D60
+ PA13: D101, PB13: D3, PC13: D20, PD13: D63
+ PA14: D102, PB14: D4, PC14: D21, PD14: D58
+
+.. csv-table::
+ :header: GPIOE, GPIOF, GPIOG
+
+ PE0: D95, PF0: D56, PG0: D85
+ PE1: D92, PF1: D59, PG1: D88
+ PE2: - PF2: D62, PG2: D91,
+ PE3: D66, PF3: D65, PG3: D94
+ PE4: D69, PF4: D68, PG4: D97
+ PE5: D72, PF5: D71, PG5: D99
+ PE6: D75, PF6: D41, PG6: D36
+ PE7: D70, PF7: D42, PG7: D35
+ PE8: D73, PF8: D43, PG8: D34
+ PE9: D76, PF9: D44, PG9: D80
+ PE10: D78, PF10: D45, PG10: D83
+ PE11: D81, PF11: D40, PG11: D30
+ PE12: D84, PF12: D74, PG12: D31
+ PE13: D87, PF13: D77, PG13: D32
+ PE14: D90, PF14: D79, PG14: D33
+
+.. _maple-native-b-timer-map:
+
+Timer Pin Map
+^^^^^^^^^^^^^
+
+The following table shows what pins are associated with a particular
+timer's capture/compare channels.
+
+There is no mistake between timers 2 and 5. They really do share
+those pins. If you like, you can remap some of the timer 2 channels
+to get extra PWM pins; see :ref:`afio_remap() (in gpio.h)
+<gpio-h-afio-remap>`.
+
+.. csv-table::
+ :header: Timer, Ch. 1, Ch. 2, Ch. 3, Ch. 4
+ :delim: |
+
+ 1 | D23 | D24 | D25 |
+ 2 | D48 | D49 | D50 | D51
+ 3 | D54 | D55 | D47 | D46
+ 4 | D38 | D39 | | D26
+ 5 | D48 | D49 | D50 | D51
+ 8 | D13 | D14 | D15 | D16
+
+.. _maple-native-b-exti-map:
+
+EXTI Line Pin Map
+^^^^^^^^^^^^^^^^^
+
+The following table shows which pins connect to which :ref:`EXTI lines
+<external-interrupts-exti-line>`.
+
+.. list-table::
+ :widths: 1 3
+ :header-rows: 1
+
+ * - EXTI Line
+ - Pins
+ * - EXTI0
+ - D7, D47, D48, D56, D64, D85, D95
+ * - EXTI1
+ - D8, D46, D49, D59, D67, D88, D92
+ * - EXTI2
+ - D9, D27, D50, D62, D91
+ * - EXTI3
+ - D10, D28, D51, D65, D66, D94, D104
+ * - EXTI4
+ - D11, D52, D68, D69, D89, D97, D105
+ * - EXTI5
+ - D12, D37, D53, D71, D72, D86, D99
+ * - EXTI6
+ - D13, D29, D36, D38, D41, D54, D75
+ * - EXTI7
+ - D14, D35, D39, D42, D55, D70
+ * - EXTI8
+ - D15, D23, D34, D43, D73, D96
+ * - EXTI9
+ - D16, D24, D26, D44, D76, D80, D98
+ * - EXTI10
+ - D0, D17, D25, D45, D78, D83, D100
+ * - EXTI11
+ - D1, D18, D30, D40, D57, D81
+ * - EXTI12
+ - D2, D19, D31, D60, D74, D84
+ * - EXTI13
+ - D3, D20, D32, D63, D77, D87, D101
+ * - EXTI14
+ - D4, D21, D33, D58, D79, D90, D102
+ * - EXTI15
+ - D5, D6, D22, D61, D82, D93, D103
+
+.. _maple-native-b-usart-map:
+
+USART Pin Map
+^^^^^^^^^^^^^
+
+The Maple Native has 3 :ref:`USART <usart>` serial ports. They
+communicate using the pins given in the following table.
+
+.. csv-table::
+ :header: Serial port, TX, RX, CK, CTS, RTS
+ :delim: |
+
+ ``Serial1`` | D24 | D25 | D23 | |
+ ``Serial2`` | D50 | D51 | D52 | D48 | D49
+ ``Serial3`` | D0 | D1 | D2 | D3 | D4
+
+The Maple Native also has 2 UART serial ports. Unlike USARTS, these
+only communicate asynchronously, and thus only have TX and RX pins.
+These are given in the following table.
+
+.. csv-table::
+ :header: Serial port, TX, RX
+ :delim: |
+
+ ``Serial4`` | D17 | D18
+ ``Serial5`` | D19 | D27
+
+.. _maple-native-b-adc-bank:
+
+Low-Noise ADC Pins
+^^^^^^^^^^^^^^^^^^
+
+.. TODO [0.0.12] finish this; ask Jess for help and confirmation
+
+Maple Native has an electrically isolated analog power plane with its
+own regulator, and a geometrically isolated ground plane,
+
+Analog input pins D41 — D55 are laid out to correspond with these
+analog planes, and our measurements indicate that they generally ofer
+low noise ADC performance. However, analog performance may vary
+depending upon the activity of other GPIOs. In particular, using PWM
+on any of pins D46 — D51, D54, and D55 may cause digital noise.
+Consult the :ref:`Maple Native beta hardware design files
+<maple-native-b-hardware>` for more details.
+
+.. _maple-native-b-board-values:
+
+Board-Specific Values
+---------------------
+
+.. TODO [0.0.12] get pwm, used pins
+
+This section lists the Maple Native's :ref:`board-specific values
+<lang-board-values>`.
+
+- ``CYCLES_PER_MICROSECOND``: 72
+- ``BOARD_BUTTON_PIN``: 6
+- ``BOARD_LED_PIN``: 22
+- ``BOARD_NR_GPIO_PINS``: 106
+- ``BOARD_NR_PWM_PINS``:
+- ``boardPWMPins``:
+- ``BOARD_NR_ADC_PINS``: 21
+- ``boardADCPins``: 7, 8, 9, 10, 11, 12, 41, 42, 43, 44, 45, 46, 47,
+ 48, 49, 50, 51, 52, 53, 54, 55
+- ``BOARD_NR_USED_PINS``:
+- ``boardUsedPins``: ``BOARD_LED_PIN``, ``BOARD_BUTTON_PIN``
+- ``BOARD_NR_USARTS``:
+- ``BOARD_USART1_TX_PIN``: 24
+- ``BOARD_USART1_RX_PIN``: 25
+- ``BOARD_USART2_TX_PIN``: 50
+- ``BOARD_USART2_RX_PIN``: 51
+- ``BOARD_USART3_TX_PIN``: 0
+- ``BOARD_USART3_RX_PIN``: 1
+- ``BOARD_UART4_TX_PIN``: 17
+- ``BOARD_UART4_RX_PIN``: 18
+- ``BOARD_UART5_TX_PIN``: 19
+- ``BOARD_UART5_RX_PIN``: 27
+- ``BOARD_NR_SPI``: 3
+- ``BOARD_SPI1_NSS_PIN``: 52
+- ``BOARD_SPI1_MOSI_PIN``: 55
+- ``BOARD_SPI1_MISO_PIN``: 54
+- ``BOARD_SPI1_SCK_PIN``: 53
+- ``BOARD_SPI2_NSS_PIN``: 2
+- ``BOARD_SPI2_MOSI_PIN``: 5
+- ``BOARD_SPI2_MISO_PIN``: 4
+- ``BOARD_SPI2_SCK_PIN``: 3
+- ``BOARD_JTMS_SWDIO_PIN``: :ref:`103 <maple-native-b-jtag>`
+- ``BOARD_JTCK_SWCLK_PIN``: 102
+- ``BOARD_JTDI_PIN``: 103
+- ``BOARD_JTDO_PIN``: 104
+- ``BOARD_NJTRST_PIN``: 105
+
+.. _maple-native-b-hardware:
+
+Hardware Design Files
+^^^^^^^^^^^^^^^^^^^^^
+
+The hardware schematics and board layout files are available in the
+`Maple Native GitHub repository
+<https://github.com/leaflabs/maplenative/>`_. Download the `beta
+version's hardware design files
+<https://github.com/leaflabs/maplenative/tree/beta>`_ (ZIP format).
+
+If you're familiar with Git, you can clone the entire repository and
+checkout the commit tagged "beta" using the following::
+
+ $ git clone git://github.com/leaflabs/maplenative.git
+ $ git checkout beta
+
+Failure Modes
+-------------
+
+The following known failure modes apply to the Maple Native Beta. The
+failure modes aren't design errors, but are easy ways to break or
+damage your board permanently.
+
+* **Reversing Vin and GND**: when powering the Maple Native Beta via
+ the Vin and ground (GND) pins at the top left of the board, it is
+ possible to carelessly cause a short or switch the connections,
+ applying the high voltage to GND and ground to Vin.
+
+ If this happens, you will reverse bias the diode beneath these pins,
+ most likely damaging it. This may cause excess voltage to
+ subsequently be delivered to the board once the reversed pins are
+ connected properly.
+
+Errata
+------
+
+This section lists known issues and warnings for the Maple Native
+Beta.
+
+* **PWM on pin 39**: PWM on pin 39 appears to be nonfunctional. We
+ are looking into this issue.
+
+Recommended Reading
+-------------------
+
+.. _maple-native-b-stdocs:
+
+STMicro documentation for STM32F103ZE microcontroller:
+
+* `Datasheet
+ <http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00191185.pdf>`_
+ (PDF); covers STM32F103xC, STM3F103xD, STM32F103xE.
+* `Reference Manual RM0008
+ <http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/REFERENCE_MANUAL/CD00171190.pdf>`_
+ (PDF); definitive resource for peripherals on the STM32F1 line.
+* `Programming Manual PM0056
+ <http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/PROGRAMMING_MANUAL/CD00228163.pdf>`_
+ (PDF); assembly language and register reference.
+* `STM32F103RE <http://www.st.com/internet/mcu/product/164485.jsp>`_
+ overview page with links to further references.
+
+.. rubric:: Footnotes
+
+.. [#fusedpins] See :ref:`boardUsedPins <lang-board-values-used-pins>`
+ for more information.
diff --git a/source/index.rst b/source/index.rst
index 7886c4f..f24262d 100644
--- a/source/index.rst
+++ b/source/index.rst
@@ -72,6 +72,7 @@ Have fun!
hardware/maple.rst
hardware/maple-ret6.rst
hardware/maple-mini.rst
+ hardware/maple-native-beta.rst
-.. TODO write/include these upon Mini and Native release
+.. TODO write/include upon Native release
.. hardware/maple-native.rst