1 files changed, 0 insertions, 166 deletions
diff --git a/source/ide.rst b/source/ide.rst
deleted file mode 100644
index e6d49fc..0000000
--- a/source/ide.rst
+++ /dev/null
@@ -1,166 +0,0 @@
-.. _ide:
-
-Using Maple IDE
-===============
-
-This page documents the basic functionality of the Maple IDE.
-Specifically, it describes the operation of the buttons on the main
-toolbar.  It is expected to become more comprehensive over time.
-
-If you're new to Maple, you should begin with the :ref:`Maple
-Quickstart <maple-quickstart>`.
-
-If you need to install the IDE for the first time, see the
-:ref:`maple-ide-install` page.
-
-.. contents:: Contents
-   :local:
-
-IDE Windows
------------
-
-The following screenshot shows the appearance of a Maple IDE window:
-
-.. figure:: /_static/img/ide-blinky.png
-   :align: center
-   :alt: Maple IDE
-
-Note the toolbar buttons at the top; they're the icons with circles or
-squares around them.  You can program your board mostly through the
-use of these buttons, which are described in the next section.
-
-Toolbar Buttons
----------------
-
-.. _ide-verify:
-
-Verify
-~~~~~~
-
-.. image:: /_static/img/button-verify.png
-   :align: left
-
-Click Verify to compile the current sketch.  This will process your
-program and produce an executable which can run on your board.
-
-.. _ide-stop:
-
-Stop
-~~~~
-
-.. image:: /_static/img/button-stop.png
-   :align: left
-
-Click Stop to cancel a compilation.  Longer programs may take a while
-to compile.  Clicking Stop will let you go back to writing code
-without having to wait for compilation to finish.
-
-.. _ide-new:
-
-New
-~~~
-
-.. image:: /_static/img/button-new.png
-   :align: left
-
-Click New to make a fresh sketch.
-
-.. _ide-open:
-
-Open
-~~~~
-
-.. image:: /_static/img/button-open.png
-   :align: left
-
-Click Open to open an existing sketch.  Maple IDE will first look for
-the sketch in your *sketchbook*, which is a folder on your computer
-that contains your sketches.  The sketchbook is stored in different
-places depending on your operating system.  You can change its
-location in the IDE's preferences.
-
-.. _ide-save:
-
-Save
-~~~~
-
-.. image:: /_static/img/button-save.png
-   :align: left
-
-Click Save to save the currently opened sketch.  This will save all
-open tabs, not just the one you're currently looking at.
-
-.. _ide-upload:
-
-Upload
-~~~~~~
-
-.. image:: /_static/img/button-upload.png
-   :align: left
-
-Click Upload to send the compiled sketch to your Maple to run.  Before
-you click Upload, you must have a memory location and serial port
-selected.
-
-The memory location, either Flash or RAM, determines whether the
-compiled sketch binary will be stored on the Maple.  You can choose
-this using the Tools > Board menu.
-
-The serial port corresponds to the :ref:`SerialUSB <lang-serialusb>`
-connection the Maple establishes with your computer.  This looks like
-"COM1", "COM2", etc. on Windows, "/dev/tty.usbmodemXXX" on Mac (where
-"XXX" is some sequence of letters and numbers), or "/dev/ttyACMXXX" on
-Linux (again, where "XXX" is some sequence of letters and numbers).
-You can choose a serial port using the Tools > Serial Port menu.
-
-If you're trying to upload and are unsuccessful, make sure you've made
-choices for both board and serial port.  More help on uploading
-(including screenshots) is available in the :ref:`quickstart
-<maple-quickstart-upload>`.
-
-If all else fails, try putting your Maple in :ref:`perpetual
-bootloader mode <troubleshooting-perpetual-bootloader>` before
-uploading.  You can always find us on the `forum`_ or `contact us
-directly`_ for help on any problems you're having.
-
-.. _ide-serial-monitor:
-
-Serial Monitor
-~~~~~~~~~~~~~~
-
-.. image:: /_static/img/button-serial-monitor.png
-   :align: left
-
-Click Serial Monitor to open up a communication channel between your
-PC and the Maple's :ref:`SerialUSB <lang-serialusb>` virtual serial
-port.
-
-If the serial monitor is open, any information sent to the computer
-(for example, using :ref:`SerialUSB.println()
-<lang-serialusb-println>`) will be displayed in the large text area.
-You can send data to the Maple by typing into the small text box and
-either hitting the Enter key or pressing the Send button.  (The Maple
-can read the data you send with :ref:`SerialUSB.read()
-<lang-serialusb-read>`).
-
-Here is an example serial monitor session with the InteractiveTest
-sketch (which you can load in the IDE by choosing menu item File >
-Examples > Maple > InteractiveTest):
-
-.. image:: /_static/img/serial-monitor.png
-
-This is the result of typing "?" in the text box and clicking Send.
-
-.. note:: You cannot upload a sketch while the serial monitor is open.
-   If you click :ref:`Upload <ide-upload>` while the serial monitor is
-   open, the IDE will close it for you before proceeding with the
-   upload.
-
-.. _ide-examples:
-
-Example Code
-------------
-
-Maple IDE comes with a variety of sample code you can use to help you
-get started writing your own programs.  To load an example in a new
-Maple IDE window, choose one from the submenus under File > Examples.