diff options
Diffstat (limited to 'libmaple')
| -rw-r--r-- | libmaple/dma.c | 35 | ||||
| -rw-r--r-- | libmaple/dma_private.h | 61 | ||||
| -rw-r--r-- | libmaple/include/libmaple/dma.h | 402 | ||||
| -rw-r--r-- | libmaple/include/libmaple/dma_common.h | 114 | ||||
| -rw-r--r-- | libmaple/stm32f1/dma.c | 381 | ||||
| -rw-r--r-- | libmaple/stm32f1/include/series/dma.h | 411 |
6 files changed, 1038 insertions, 366 deletions
diff --git a/libmaple/dma.c b/libmaple/dma.c index 6442e4d..d13de10 100644 --- a/libmaple/dma.c +++ b/libmaple/dma.c @@ -33,6 +33,8 @@ */ #include <libmaple/dma.h> +#include "dma_private.h" +#include "stm32_private.h" /* * Convenience routines @@ -45,3 +47,36 @@ void dma_init(dma_dev *dev) { rcc_clk_enable(dev->clk_id); } + +/* + * Private API + */ + +enum dma_atype _dma_addr_type(__io void *addr) { + switch (stm32_block_purpose((void*)addr)) { + /* Notice we're treating the code block as memory here. That's + * correct for addresses in Flash and in [0x0, 0x7FFFFFF] + * (provided that those addresses are aliased to Flash, SRAM, or + * FSMC, depending on BOOT[01] and possibly SYSCFG_MEMRMP). It's + * not correct for other addresses in the code block, but those + * will (hopefully) just fail-fast with transfer or bus errors. If + * lots of people get confused, it might be worth being more + * careful here. */ + case STM32_BLOCK_CODE: /* Fall through */ + case STM32_BLOCK_SRAM: /* ... */ + case STM32_BLOCK_FSMC_1_2: /* ... */ + case STM32_BLOCK_FSMC_3_4: + return DMA_ATYPE_MEM; + case STM32_BLOCK_PERIPH: + return DMA_ATYPE_PER; + case STM32_BLOCK_FSMC_REG: /* Fall through */ + /* Is this right? I can't think of a reason to DMA into or out + * of the FSMC registers. [mbolivar] */ + case STM32_BLOCK_UNUSED: /* ... */ + case STM32_BLOCK_CORTEX_INTERNAL: /* ... */ + return DMA_ATYPE_OTHER; + default: + ASSERT(0); /* Can't happen */ + return DMA_ATYPE_OTHER; + } +} diff --git a/libmaple/dma_private.h b/libmaple/dma_private.h new file mode 100644 index 0000000..b25ded2 --- /dev/null +++ b/libmaple/dma_private.h @@ -0,0 +1,61 @@ +/****************************************************************************** + * The MIT License + * + * Copyright (c) 2012 LeafLabs, LLC. + * + * Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, copy, + * modify, merge, publish, distribute, sublicense, and/or sell copies + * of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF + * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS + * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN + * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE + * SOFTWARE. +*****************************************************************************/ + +#ifndef _LIBMAPLE_DMA_PRIVATE_H_ +#define _LIBMAPLE_DMA_PRIVATE_H_ + +#include <libmaple/dma.h> +#include <libmaple/libmaple_types.h> + +/* + * IRQ handling + */ + +/* Wrap this in an ifdef to shut up GCC. (We provide DMA_GET_HANDLER + * in the series support files, which need dma_irq_handler().) */ +#ifdef DMA_GET_HANDLER +static __always_inline void dma_irq_handler(dma_dev *dev, dma_tube tube) { + void (*handler)(void) = DMA_GET_HANDLER(dev, tube); + if (handler) { + handler(); + dma_clear_isr_bits(dev, tube); /* in case handler doesn't */ + } +} +#endif + +/* + * Conveniences for dealing with tube sources/destinations + */ + +enum dma_atype { + DMA_ATYPE_MEM, + DMA_ATYPE_PER, + DMA_ATYPE_OTHER, +}; + +enum dma_atype _dma_addr_type(__io void *addr); + +#endif diff --git a/libmaple/include/libmaple/dma.h b/libmaple/include/libmaple/dma.h index 0aed572..0ef495a 100644 --- a/libmaple/include/libmaple/dma.h +++ b/libmaple/include/libmaple/dma.h @@ -42,49 +42,399 @@ extern "C"{ /* <series/dma.h> provides: * + * - An opaque dma_tube type, and predefined rvalues for each tube + * supported by the series. + * + * A "DMA tube" is a series-specific (hopefully integer) datatype + * that abstracts the conduit through which DMA-ed data flow. + * + * Examples: On STM32F1, dma_tube is just an alias for dma_channel, + * and the tube values are just DMA_CH1 (=1), DMA_CH2 (=2), etc. + * + * Note that a dma_tube doesn't have to be an enum, and its values + * don't have to be integral. They _do_ need to be cheap to pass as + * arguments, though. + * + * - struct dma_tube_reg_map (and typedef to dma_tube_reg_map). DMA + * register maps tend to be split into global registers and per-tube + * registers. It's convenient to pass around pointers to a tube's + * registers, since that makes it possible to configure or otherwise + * mess with a tube without knowing which one you're dealing with. + * + * - Base pointers to the various dma_tube_reg_maps. + * + * Examples: On STM32F1, these are DMAxCHy_BASE. You can access + * registers like DMAxCHy_BASE->CPAR, etc. + * + * - enum dma_request_src (and typedef to dma_request_src). This + * specifies the peripheral DMA request sources (e.g. USART TX DMA + * requests, etc.). + * + * - enum dma_mode_flags (and typedef to dma_mode_flags). Used in + * dma_tube_config. If two series both support the same mode flags, + * they must use the same enumerator names for those flags (the + * values of those enumerators are of course allowed to differ). + * * - Normal stuff: dma_reg_map and base pointers, register bit * definitions, dma_dev pointer declarations, and any other - * convenience functions useful for that series. - */ + * convenience functions useful for the series. */ #include <series/dma.h> - +/* <libmaple/dma_common.h> buys us dma_dev and other necessities. */ +#include <libmaple/dma_common.h> #include <libmaple/libmaple_types.h> -#include <libmaple/nvic.h> -#include <libmaple/rcc.h> /* - * Devices + * Declarations/documentation for some of the series-provided types. + */ + +/** + * @brief (Series-dependent) DMA request sources. + * + * These specify the various pieces of peripheral functionality which + * may make DMA requests. Use them to set up a DMA transfer (see + * struct dma_tube_config, dma_tube_cfg()). */ +enum dma_request_src; -/* Encapsulates state related to user interrupt handlers. You - * shouldn't touch these directly; use dma_attach_interrupt() and - * dma_detach_interupt() instead. */ -typedef struct dma_handler_config { - void (*handler)(void); /* User handler */ - nvic_irq_num irq_line; /* IRQ line for interrupt */ -} dma_handler_config; +/** + * @brief (Series-dependent) DMA tube configuration flags. + * These specify miscellaneous bits of configuration for a DMA tube. + * @see struct dma_mode_config + */ +enum dma_cfg_flags; -/** DMA device type */ -typedef struct dma_dev { - dma_reg_map *regs; /**< Register map */ - rcc_clk_id clk_id; /**< Clock ID */ - struct dma_handler_config handlers[]; /**< For internal use */ -} dma_dev; +/** + * @brief (Series-dependent) DMA tube register map type. + * This allows you to access a tube's registers as a group. + * @see dma_tube_regs() + */ +struct dma_tube_reg_map; /* * Convenience functions */ +/* Initialization */ + void dma_init(dma_dev *dev); -/* - * Hack: This is here so the series header can declare it and access - * dma_dev->regs without knowing the structure of dma_dev. Don't use - * it outside of a series header. +/* dma_tube configuration + * + * Use these types and functions to set up DMA transfers, handle + * interrupts, etc. The main function of interest is dma_tube_cfg(), + * which the various series implement separately. */ + +/** + * @brief Specifies a DMA tube configuration. + * + * Use one of these to set up a DMA transfer by passing it to + * dma_tube_cfg(). + * + * @see dma_tube_cfg() + * @see dma_xfer_size + */ +typedef struct dma_tube_config { + /** Source of data */ + __io void *tube_src; + /** Source transfer size */ + dma_xfer_size tube_src_size; + + /** Destination of data */ + __io void *tube_dst; + /** Destination transfer size */ + dma_xfer_size tube_dst_size; + + /** + * Number of data to transfer (0 to 65,535). + * + * Note that this is NOT measured in bytes; it's measured in + * number of data, which occur in multiples of tube_src_size. For + * example, if tube_src_size is DMA_SIZE_32BITS and tube_nr_xfers + * is 2, then 8 total bytes will be transferred. + */ + unsigned tube_nr_xfers; + + /** + * Target-specific configuration flags. + * + * These are an OR of series-specific enum dma_mode_flags values. + * Consult the documentation for your target for what flags you + * can use here. + * + * Typical flag examples: DMA_CFG_SRC_INC, DMA_CFG_DST_INC, + * DMA_CFG_CIRC, DMA_CFG_CMPLT_IE, etc. + */ + unsigned tube_flags; + + /** + * Currently unused. You must set this to 0 or something valid for + * your target. */ + void *target_data; + + /** + * Hardware DMA request source. + * + * This is ignored for memory-to-memory transfers. + */ + enum dma_request_src tube_req_src; +} dma_tube_config; + +#define DMA_TUBE_CFG_SUCCESS 0 +#define DMA_TUBE_CFG_EREQ 1 +#define DMA_TUBE_CFG_ENDATA 2 +#define DMA_TUBE_CFG_EDEV 3 +#define DMA_TUBE_CFG_ESRC 4 +#define DMA_TUBE_CFG_EDST 5 +#define DMA_TUBE_CFG_EDIR 6 +#define DMA_TUBE_CFG_ESIZE 7 +#define DMA_TUBE_CFG_ECFG 0xFF +/** + * @brief Configure a DMA tube. + * + * Use this function to set up a DMA transfer. The tube will be + * disabled before being reconfigured. The transfer will have low + * priority by default. You can choose another priority before the + * transfer begins using dma_set_priority(). You can manage your + * interrupt handlers for the tube using dma_attach_interrupt() and + * dma_detach_interrupt(). + * + * After calling dma_tube_cfg() and performing any other desired + * configuration, start the transfer using dma_enable(). + * + * @param dev DMA device. + * @param tube DMA tube to configure. + * @param cfg Configuration to apply to tube. + * + * @return DMA_TUBE_CFG_SUCCESS (0) on success, <0 on failure. On + * failure, returned value will be the opposite (-) of one of: + * + * - DMA_TUBE_CFG_EREQ: tube doesn't work with cfg->tube_req_src + * - DMA_TUBE_CFG_ENDATA: cfg->tube_[src,dst]_size are + * incompatible with cfg->tube_nr_xfers, or cfg->tube_nr_xfers + * is out of bounds. + * - DMA_TUBE_CFG_EDEV: dev does not support cfg + * - DMA_TUBE_CFG_ESRC: bad cfg->tube_src + * - DMA_TUBE_CFG_EDST: bad cfg->tube_dst + * - DMA_TUBE_CFG_EDIR: dev can't transfer from cfg->tube_src to + * cfg->tube_dst + * - DMA_TUBE_CFG_ESIZE: something ended up wrong due to MSIZE/PSIZE + * - DMA_TUBE_CFG_ECFG: generic "something's wrong" + * + * @sideeffect Disables tube. May alter tube's registers even when an + * error occurs. + * @see struct dma_tube_config + * @see dma_attach_interrupt() + * @see dma_detach_interrupt() + * @see dma_enable() + */ +extern int dma_tube_cfg(dma_dev *dev, dma_tube tube, dma_tube_config *cfg); + +/* Other tube configuration functions. You can use these if + * dma_tube_cfg() isn't enough, or to adjust parts of an existing tube + * configuration. */ + +/** DMA transfer priority. */ +typedef enum dma_priority { + DMA_PRIORITY_LOW = 0, /**< Low priority */ + DMA_PRIORITY_MEDIUM = 1, /**< Medium priority */ + DMA_PRIORITY_HIGH = 2, /**< High priority */ + DMA_PRIORITY_VERY_HIGH = 3, /**< Very high priority */ +} dma_priority; + +/** + * @brief Set the priority of a DMA transfer. + * + * You may not call this function while the tube is enabled. + * + * @param dev DMA device + * @param tube DMA tube + * @param priority priority to set. + */ +extern void dma_set_priority(dma_dev *dev, dma_tube tube, + dma_priority priority); + +/** + * @brief Set the number of data transfers on a DMA tube. + * + * You may not call this function while the tube is enabled. + * + * @param dev DMA device + * @param tube Tube through which the transfer will occur. + * @param num_transfers Number of DMA transactions to set. + */ +extern void dma_set_num_transfers(dma_dev *dev, dma_tube tube, + uint16 num_transfers); + +/** + * @brief Set the base memory address where data will be read from or + * written to. + * + * You must not call this function while the tube is enabled. + * + * If the DMA memory size is 16 bits, the address is automatically + * aligned to a half-word. If the DMA memory size is 32 bits, the + * address is aligned to a word. + * + * @param dev DMA Device + * @param tube Tube whose base memory address to set. + * @param address Memory base address to use. + */ +extern void dma_set_mem_addr(dma_dev *dev, dma_tube tube, __io void *address); + +/** + * @brief Set the base peripheral address where data will be read from + * or written to. + * + * You must not call this function while the channel is enabled. + * + * If the DMA peripheral size is 16 bits, the address is automatically + * aligned to a half-word. If the DMA peripheral size is 32 bits, the + * address is aligned to a word. + * + * @param dev DMA Device + * @param tube Tube whose peripheral data register base address to set. + * @param addr Peripheral memory base address to use. + */ +extern void dma_set_per_addr(dma_dev *dev, dma_tube tube, __io void *address); + +/* Interrupt handling */ + +/** + * @brief Attach an interrupt to a DMA transfer. + * + * Interrupts are enabled using series-specific mode flags in + * dma_tube_cfg(). + * + * @param dev DMA device + * @param tube Tube to attach handler to + * @param handler Interrupt handler to call when tube interrupt fires. + * @see dma_tube_cfg() + * @see dma_get_irq_cause() + * @see dma_detach_interrupt() + */ +extern void dma_attach_interrupt(dma_dev *dev, dma_tube tube, + void (*handler)(void)); + + +/** + * @brief Detach a DMA transfer interrupt handler. + * + * After calling this function, the given tube's interrupts will be + * disabled. + * + * @param dev DMA device + * @param tube Tube whose handler to detach + * @sideeffect Clears the tube's interrupt enable bits. + * @see dma_attach_interrupt() + */ +extern void dma_detach_interrupt(dma_dev *dev, dma_tube tube); + +/* Tube enable/disable */ + +/** + * @brief Enable a DMA tube. + * + * If the tube has been properly configured, calling this function + * allows it to start serving DMA requests. + * + * @param dev DMA device + * @param tube Tube to enable + * @see dma_tube_cfg() + */ +extern void dma_enable(dma_dev *dev, dma_tube tube); + +/** + * @brief Disable a DMA channel. + * + * Calling this function makes the tube stop serving DMA requests. + * + * @param dev DMA device + * @param tube Tube to disable + */ +extern void dma_disable(dma_dev *dev, dma_tube tube); + +/** + * @brief Check if a DMA tube is enabled. + * @param dev DMA device. + * @param tube Tube to check. + * @return 0 if the tube is disabled, >0 if it is enabled. + */ +static inline uint8 dma_is_enabled(dma_dev *dev, dma_tube tube); + +/* Other conveniences */ + +/** + * @brief Obtain a pointer to an individual DMA tube's registers. + * + * Examples: + * + * - On STM32F1, dma_channel_regs(DMA1, DMA_CH1)->CCR is DMA1_BASE->CCR1. + * + * @param dev DMA device. + * @param tube DMA tube whose register map to obtain. + * @return (Series-specific) tube register map. + */ +static inline dma_tube_reg_map* dma_tube_regs(dma_dev *dev, dma_tube tube); + +/** + * Encodes the reason why a DMA interrupt was called. + * @see dma_get_irq_cause() + */ +typedef enum dma_irq_cause { + DMA_TRANSFER_COMPLETE, /**< Transfer is complete. */ + DMA_TRANSFER_HALF_COMPLETE, /**< Transfer is half complete. */ + DMA_TRANSFER_ERROR, /**< Error occurred during transfer. */ + DMA_TRANSFER_DME_ERROR, /**< + * @brief Direct mode error occurred during + * transfer. */ + DMA_TRANSFER_FIFO_ERROR, /**< FIFO error occurred during transfer. */ +} dma_irq_cause; + +/** + * @brief Discover the reason why a DMA interrupt was called. + * + * You may only call this function within an attached interrupt + * handler for the given channel. + * + * This function resets the internal DMA register state which encodes + * the cause of the interrupt; consequently, it can only be called + * once per interrupt handler invocation. + * + * @param dev DMA device + * @param tube Tube whose interrupt is being handled. + * @return Reason why the interrupt fired. + * @sideeffect Clears flags in dev's interrupt status registers. + * @see dma_attach_interrupt() + * @see dma_irq_cause + */ +extern dma_irq_cause dma_get_irq_cause(dma_dev *dev, dma_tube tube); + +/** + * @brief Get the ISR status bits for a DMA channel. + * + * The bits are returned right-aligned, in the order they appear in + * the corresponding ISR register. + * + * If you're trying to figure out why a DMA interrupt fired, you may + * find dma_get_irq_cause() more convenient. + * + * @param dev DMA device + * @param tube Tube whose ISR bits to return. + * @see dma_get_irq_cause(). + */ +static inline uint8 dma_get_isr_bits(dma_dev *dev, dma_tube tube); + +/** + * @brief Clear the ISR status bits for a given DMA tube. + * + * If you're trying to clean up after yourself in a DMA interrupt, you + * may find dma_get_irq_cause() more convenient. + * + * @param dev DMA device + * @param tube Tube whose ISR bits to clear. + * @see dma_get_irq_cause() */ -static __always_inline dma_reg_map* _dma_dev_regs(dma_dev *dev) { - return dev->regs; -} +static inline void dma_clear_isr_bits(dma_dev *dev, dma_tube tube); #ifdef __cplusplus } // extern "C" diff --git a/libmaple/include/libmaple/dma_common.h b/libmaple/include/libmaple/dma_common.h new file mode 100644 index 0000000..67475f7 --- /dev/null +++ b/libmaple/include/libmaple/dma_common.h @@ -0,0 +1,114 @@ +/****************************************************************************** + * The MIT License + * + * Copyright (c) 2012 LeafLabs, LLC. + * + * Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, copy, + * modify, merge, publish, distribute, sublicense, and/or sell copies + * of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF + * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS + * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN + * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE + * SOFTWARE. + *****************************************************************************/ + +/** + * @file libmaple/include/libmaple/dma_common.h + * @author Marti Bolivar <mbolivar@leaflabs.com> + * @brief Common DMA sub-header for <series/dma.h> and <libmaple/dma.h>. + * + * WARNING: CONTENTS UNSTABLE + * + * The existence of this file is an implementation detail. Its + * contents are not stable, so never include it directly. If you need + * something from here, #include <libmaple/dma.h> instead. + */ + +/* + * There's a fair amount of common DMA functionality needed by each + * <series/dma.h> and <libmaple/dma.h>. This header exists in order + * to provide it to both, avoiding some hacks and circular + * dependencies. + */ + +#ifndef _LIBMAPLE_DMA_COMMON_H_ +#define _LIBMAPLE_DMA_COMMON_H_ + +#ifdef __cplusplus +extern "C"{ +#endif + +#include <libmaple/libmaple_types.h> +#include <libmaple/nvic.h> +#include <libmaple/rcc.h> + +/* + * Devices + */ + +struct dma_reg_map; + +/* Encapsulates state related to user interrupt handlers. You + * shouldn't touch these directly; use dma_attach_interrupt() and + * dma_detach_interupt() instead. */ +typedef struct dma_handler_config { + void (*handler)(void); /* User handler */ + nvic_irq_num irq_line; /* IRQ line for interrupt */ +} dma_handler_config; + +/** DMA device type */ +typedef struct dma_dev { + struct dma_reg_map *regs; /**< Register map */ + rcc_clk_id clk_id; /**< Clock ID */ + struct dma_handler_config handlers[]; /**< For internal use */ +} dma_dev; + +/** + * @brief DMA channels + * + * Notes: + * - This is also the dma_tube type for STM32F1. + * - Channel 0 is not available on all STM32 series. + * + * @see dma_tube + */ +typedef enum dma_channel { + DMA_CH0 = 0, /**< Channel 0 */ + DMA_CH1 = 1, /**< Channel 1 */ + DMA_CH2 = 2, /**< Channel 2 */ + DMA_CH3 = 3, /**< Channel 3 */ + DMA_CH4 = 4, /**< Channel 4 */ + DMA_CH5 = 5, /**< Channel 5 */ + DMA_CH6 = 6, /**< Channel 6 */ + DMA_CH7 = 7, /**< Channel 7 */ +} dma_channel; + +/** + * @brief Source and destination transfer sizes. + * Use these when initializing a struct dma_tube_config. + * @see struct dma_tube_config + * @see dma_tube_cfg + */ +typedef enum dma_xfer_size { + DMA_SIZE_8BITS = 0, /**< 8-bit transfers */ + DMA_SIZE_16BITS = 1, /**< 16-bit transfers */ + DMA_SIZE_32BITS = 2, /**< 32-bit transfers */ +} dma_xfer_size; + +#ifdef __cplusplus +} // extern "C" +#endif + +#endif diff --git a/libmaple/stm32f1/dma.c b/libmaple/stm32f1/dma.c index 14ac645..fc502a1 100644 --- a/libmaple/stm32f1/dma.c +++ b/libmaple/stm32f1/dma.c @@ -35,6 +35,10 @@ #include <libmaple/dma.h> #include <libmaple/bitband.h> +/* Hack to ensure inlining in dma_irq_handler() */ +#define DMA_GET_HANDLER(dev, tube) (dev->handlers[tube - 1].handler) +#include "dma_private.h" + /* * Devices */ @@ -50,7 +54,7 @@ static dma_dev dma1 = { { .handler = NULL, .irq_line = NVIC_DMA_CH6 }, { .handler = NULL, .irq_line = NVIC_DMA_CH7 }}, }; -/** DMA1 device */ +/** STM32F1 DMA1 device */ dma_dev *DMA1 = &dma1; #if defined(STM32_HIGH_DENSITY) || defined(STM32_XL_DENSITY) @@ -63,83 +67,95 @@ static dma_dev dma2 = { { .handler = NULL, .irq_line = NVIC_DMA2_CH_4_5 }, { .handler = NULL, .irq_line = NVIC_DMA2_CH_4_5 }}, /* !@#$ */ }; -/** DMA2 device */ +/** STM32F1 DMA2 device */ dma_dev *DMA2 = &dma2; #endif /* - * Routines + * Auxiliary routines */ -/** - * @brief Set up a DMA transfer. - * - * The channel will be disabled before being reconfigured. The - * transfer will have low priority by default. You may choose another - * priority before the transfer begins using dma_set_priority(), as - * well as performing any other configuration you desire. When the - * channel is configured to your liking, enable it using dma_enable(). - * - * @param dev DMA device. - * @param channel DMA channel. - * @param peripheral_address Base address of peripheral data register - * involved in the transfer. - * @param peripheral_size Peripheral data transfer size. - * @param memory_address Base memory address involved in the transfer. - * @param memory_size Memory data transfer size. - * @param mode Logical OR of dma_mode_flags - * @sideeffect Disables the given DMA channel. - * @see dma_xfer_size - * @see dma_mode_flags - * @see dma_set_num_transfers() - * @see dma_set_priority() - * @see dma_attach_interrupt() - * @see dma_enable() - */ -void dma_setup_transfer(dma_dev *dev, - dma_channel channel, - __io void *peripheral_address, - dma_xfer_size peripheral_size, - __io void *memory_address, - dma_xfer_size memory_size, - uint32 mode) { - dma_channel_reg_map *channel_regs = dma_channel_regs(dev, channel); +/* Can channel serve cfg->tube_req_src? */ +static int cfg_req_ok(dma_channel channel, dma_tube_config *cfg) { + return (cfg->tube_req_src & 0x7) == channel; +} - dma_disable(dev, channel); /* can't write to CMAR/CPAR otherwise */ - channel_regs->CCR = (memory_size << 10) | (peripheral_size << 8) | mode; - channel_regs->CMAR = (uint32)memory_address; - channel_regs->CPAR = (uint32)peripheral_address; +/* Can dev serve cfg->tube_req_src? */ +static int cfg_dev_ok(dma_dev *dev, dma_tube_config *cfg) { + return (rcc_clk_id)(cfg->tube_req_src >> 3) == dev->clk_id; } -/** - * @brief Set the number of data to be transferred on a DMA channel. - * - * You may not call this function while the channel is enabled. - * - * @param dev DMA device - * @param channel Channel through which the transfer occurs. - * @param num_transfers - */ -void dma_set_num_transfers(dma_dev *dev, - dma_channel channel, - uint16 num_transfers) { - dma_channel_reg_map *channel_regs; +/* Is addr acceptable for use as DMA src/dst? */ +static int cfg_mem_ok(__io void *addr) { + enum dma_atype atype = _dma_addr_type(addr); + return atype == DMA_ATYPE_MEM || atype == DMA_ATYPE_PER; +} - ASSERT_FAULT(!dma_is_channel_enabled(dev, channel)); +/* Is the direction implied by src->dst supported? */ +static int cfg_dir_ok(dma_tube_config *cfg) { + /* We can't do peripheral->peripheral transfers. */ + return ((_dma_addr_type(cfg->tube_src) == DMA_ATYPE_MEM) || + (_dma_addr_type(cfg->tube_dst) == DMA_ATYPE_MEM)); +} - channel_regs = dma_channel_regs(dev, channel); - channel_regs->CNDTR = num_transfers; +static int preconfig_check(dma_dev *dev, dma_channel channel, + dma_tube_config *cfg) { + if (!cfg_req_ok(channel, cfg)) { + return -DMA_TUBE_CFG_EREQ; + } + if (cfg->tube_nr_xfers > 65535) { + return -DMA_TUBE_CFG_ENDATA; + } + if (!cfg_dev_ok(dev, cfg)) { + return -DMA_TUBE_CFG_EDEV; + } + if (!cfg_mem_ok(cfg->tube_src)) { + return -DMA_TUBE_CFG_ESRC; + } + if (!cfg_mem_ok(cfg->tube_dst)) { + return -DMA_TUBE_CFG_EDST; + } + if (!cfg_dir_ok(cfg)) { + return -DMA_TUBE_CFG_EDIR; + } + return DMA_TUBE_CFG_SUCCESS; } -/** - * @brief Set the priority of a DMA transfer. - * - * You may not call this function while the channel is enabled. - * - * @param dev DMA device - * @param channel DMA channel - * @param priority priority to set. +/* Configure chregs according to cfg, where cfg->tube_dst is peripheral. */ +static int config_to_per(dma_tube_reg_map *chregs, dma_tube_config *cfg) { + return -DMA_TUBE_CFG_ECFG; /* FIXME implement */ +} + +/* Configure chregs according to cfg, where cfg->tube_dst is memory. */ +static int config_to_mem(dma_tube_reg_map *chregs, dma_tube_config *cfg) { + return -DMA_TUBE_CFG_ECFG; /* FIXME implement */ +} + +/* + * Routines */ + +int dma_tube_cfg(dma_dev *dev, dma_channel channel, dma_tube_config *cfg) { + dma_tube_reg_map *chregs; + int ret = preconfig_check(dev, channel, cfg); + + if (ret < 0) { + return ret; + } + + chregs = dma_tube_regs(dev, channel); + switch (_dma_addr_type(cfg->tube_dst)) { + case DMA_ATYPE_PER: + return config_to_per(chregs, cfg); + case DMA_ATYPE_MEM: + return config_to_mem(chregs, cfg); + default: + /* Can't happen */ + ASSERT(0); + return -DMA_TUBE_CFG_ECFG; + } +} + void dma_set_priority(dma_dev *dev, dma_channel channel, dma_priority priority) { @@ -151,134 +167,77 @@ void dma_set_priority(dma_dev *dev, channel_regs = dma_channel_regs(dev, channel); ccr = channel_regs->CCR; ccr &= ~DMA_CCR_PL; - ccr |= priority; + ccr |= (priority << 12); channel_regs->CCR = ccr; } -/** - * @brief Attach an interrupt to a DMA transfer. - * - * Interrupts are enabled using appropriate mode flags in - * dma_setup_transfer(). - * - * @param dev DMA device - * @param channel Channel to attach handler to - * @param handler Interrupt handler to call when channel interrupt fires. - * @see dma_setup_transfer() - * @see dma_get_irq_cause() - * @see dma_detach_interrupt() - */ -void dma_attach_interrupt(dma_dev *dev, - dma_channel channel, +void dma_set_num_transfers(dma_dev *dev, + dma_channel channel, + uint16 num_transfers) { + dma_channel_reg_map *channel_regs; + + ASSERT_FAULT(!dma_is_channel_enabled(dev, channel)); + + channel_regs = dma_channel_regs(dev, channel); + channel_regs->CNDTR = num_transfers; +} + +void dma_attach_interrupt(dma_dev *dev, dma_channel channel, void (*handler)(void)) { - dev->handlers[channel - 1].handler = handler; + DMA_GET_HANDLER(dev, channel) = handler; nvic_irq_enable(dev->handlers[channel - 1].irq_line); } -/** - * @brief Detach a DMA transfer interrupt handler. - * - * After calling this function, the given channel's interrupts will be - * disabled. - * - * @param dev DMA device - * @param channel Channel whose handler to detach - * @sideeffect Clears interrupt enable bits in the channel's CCR register. - * @see dma_attach_interrupt() - */ void dma_detach_interrupt(dma_dev *dev, dma_channel channel) { /* Don't use nvic_irq_disable()! Think about DMA2 channels 4 and 5. */ dma_channel_regs(dev, channel)->CCR &= ~0xF; - dev->handlers[channel - 1].handler = NULL; + DMA_GET_HANDLER(dev, channel) = NULL; +} + +void dma_enable(dma_dev *dev, dma_channel channel) { + dma_channel_reg_map *chan_regs = dma_channel_regs(dev, channel); + bb_peri_set_bit(&chan_regs->CCR, DMA_CCR_EN_BIT, 1); +} + +void dma_disable(dma_dev *dev, dma_channel channel) { + dma_channel_reg_map *chan_regs = dma_channel_regs(dev, channel); + bb_peri_set_bit(&chan_regs->CCR, DMA_CCR_EN_BIT, 0); } -/** - * @brief Discover the reason why a DMA interrupt was called. - * - * You may only call this function within an attached interrupt - * handler for the given channel. - * - * This function resets the internal DMA register state which encodes - * the cause of the interrupt; consequently, it can only be called - * once per interrupt handler invocation. - * - * @param dev DMA device - * @param channel Channel whose interrupt is being handled. - * @return Reason why the interrupt fired. - * @sideeffect Clears channel status flags in dev->regs->ISR. - * @see dma_attach_interrupt() - * @see dma_irq_cause - */ dma_irq_cause dma_get_irq_cause(dma_dev *dev, dma_channel channel) { + /* Grab and clear the ISR bits. */ uint8 status_bits = dma_get_isr_bits(dev, channel); + dma_clear_isr_bits(dev, channel); /* If the channel global interrupt flag is cleared, then * something's very wrong. */ - ASSERT(status_bits & BIT(0)); - - dma_clear_isr_bits(dev, channel); + ASSERT(status_bits & 0x1); + /* If GIF is set, then some other flag should be set, barring + * something unexpected (e.g. the user making an unforeseen IFCR + * write). */ + ASSERT(status_bits != 0x1); /* ISR flags get set even if the corresponding interrupt enable * bits in the channel's configuration register are cleared, so we * can't use a switch here. * * Don't change the order of these if statements. */ - if (status_bits & BIT(3)) { + if (status_bits & 0x8) { return DMA_TRANSFER_ERROR; - } else if (status_bits & BIT(1)) { + } else if (status_bits & 0x2) { return DMA_TRANSFER_COMPLETE; - } else if (status_bits & BIT(2)) { + } else if (status_bits & 0x4) { return DMA_TRANSFER_HALF_COMPLETE; - } else if (status_bits & BIT(0)) { - /* Shouldn't happen (unless someone messed up an IFCR write). */ - throb(); - } -#if DEBUG_LEVEL < DEBUG_ALL - else { - /* We shouldn't have been called, but the debug level is too - * low for the above ASSERT() to have had any effect. In - * order to fail fast, mimic the DMA controller's behavior - * when an error occurs. */ - dma_disable(dev, channel); } -#endif - return DMA_TRANSFER_ERROR; -} -/** - * @brief Enable a DMA channel. - * @param dev DMA device - * @param channel Channel to enable - */ -void dma_enable(dma_dev *dev, dma_channel channel) { - dma_channel_reg_map *chan_regs = dma_channel_regs(dev, channel); - bb_peri_set_bit(&chan_regs->CCR, DMA_CCR_EN_BIT, 1); -} - -/** - * @brief Disable a DMA channel. - * @param dev DMA device - * @param channel Channel to disable - */ -void dma_disable(dma_dev *dev, dma_channel channel) { - dma_channel_reg_map *chan_regs = dma_channel_regs(dev, channel); - bb_peri_set_bit(&chan_regs->CCR, DMA_CCR_EN_BIT, 0); + /* If we get here, one of our assumptions has been violated, but + * the debug level is too low for the above ASSERTs() to have had + * any effect. In order to fail fast, mimic the DMA controller's + * behavior when an error occurs. */ + dma_disable(dev, channel); + return DMA_TRANSFER_ERROR; } -/** - * @brief Set the base memory address where data will be read from or - * written to. - * - * You must not call this function while the channel is enabled. - * - * If the DMA memory size is 16 bits, the address is automatically - * aligned to a half-word. If the DMA memory size is 32 bits, the - * address is aligned to a word. - * - * @param dev DMA Device - * @param channel Channel whose base memory address to set. - * @param addr Memory base address to use. - */ void dma_set_mem_addr(dma_dev *dev, dma_channel channel, __io void *addr) { dma_channel_reg_map *chan_regs; @@ -288,20 +247,6 @@ void dma_set_mem_addr(dma_dev *dev, dma_channel channel, __io void *addr) { chan_regs->CMAR = (uint32)addr; } -/** - * @brief Set the base peripheral address where data will be read from - * or written to. - * - * You must not call this function while the channel is enabled. - * - * If the DMA peripheral size is 16 bits, the address is automatically - * aligned to a half-word. If the DMA peripheral size is 32 bits, the - * address is aligned to a word. - * - * @param dev DMA Device - * @param channel Channel whose peripheral data register base address to set. - * @param addr Peripheral memory base address to use. - */ void dma_set_per_addr(dma_dev *dev, dma_channel channel, __io void *addr) { dma_channel_reg_map *chan_regs; @@ -311,61 +256,103 @@ void dma_set_per_addr(dma_dev *dev, dma_channel channel, __io void *addr) { chan_regs->CPAR = (uint32)addr; } -/* - * IRQ handlers +/** + * @brief Deprecated. Use dma_tube_cfg() instead. + * + * Set up a DMA transfer. + * + * The channel will be disabled before being reconfigured. The + * transfer will have low priority by default. You may choose another + * priority before the transfer begins using dma_set_priority(), as + * well as performing any other configuration you desire. When the + * channel is configured to your liking, enable it using dma_enable(). + * + * @param dev DMA device. + * @param channel DMA channel. + * @param peripheral_address Base address of peripheral data register + * involved in the transfer. + * @param peripheral_size Peripheral data transfer size. + * @param memory_address Base memory address involved in the transfer. + * @param memory_size Memory data transfer size. + * @param mode Logical OR of dma_mode_flags + * + * @see dma_tube_cfg() + * + * @sideeffect Disables the given DMA channel. + * @see dma_xfer_size + * @see dma_mode_flags + * @see dma_set_num_transfers() + * @see dma_set_priority() + * @see dma_attach_interrupt() + * @see dma_enable() */ +__deprecated +void dma_setup_transfer(dma_dev *dev, + dma_channel channel, + __io void *peripheral_address, + dma_xfer_size peripheral_size, + __io void *memory_address, + dma_xfer_size memory_size, + uint32 mode) { + dma_channel_reg_map *channel_regs = dma_channel_regs(dev, channel); -static __always_inline void dispatch_handler(dma_dev *dev, int channel) { - void (*handler)(void) = dev->handlers[channel - 1].handler; - if (handler) { - handler(); - dma_clear_isr_bits(dev, channel); /* in case handler doesn't */ - } + dma_disable(dev, channel); /* can't write to CMAR/CPAR otherwise */ + channel_regs->CCR = (memory_size << 10) | (peripheral_size << 8) | mode; + channel_regs->CMAR = (uint32)memory_address; + channel_regs->CPAR = (uint32)peripheral_address; } +/* + * IRQ handlers + */ + void __irq_dma1_channel1(void) { - dispatch_handler(DMA1, DMA_CH1); + dma_irq_handler(DMA1, DMA_CH1); } void __irq_dma1_channel2(void) { - dispatch_handler(DMA1, DMA_CH2); + dma_irq_handler(DMA1, DMA_CH2); } void __irq_dma1_channel3(void) { - dispatch_handler(DMA1, DMA_CH3); + dma_irq_handler(DMA1, DMA_CH3); } void __irq_dma1_channel4(void) { - dispatch_handler(DMA1, DMA_CH4); + dma_irq_handler(DMA1, DMA_CH4); } void __irq_dma1_channel5(void) { - dispatch_handler(DMA1, DMA_CH5); + dma_irq_handler(DMA1, DMA_CH5); } void __irq_dma1_channel6(void) { - dispatch_handler(DMA1, DMA_CH6); + dma_irq_handler(DMA1, DMA_CH6); } void __irq_dma1_channel7(void) { - dispatch_handler(DMA1, DMA_CH7); + dma_irq_handler(DMA1, DMA_CH7); } -#ifdef STM32_HIGH_DENSITY +#if defined(STM32_HIGH_DENSITY) || defined(STM32_XL_DENSITY) void __irq_dma2_channel1(void) { - dispatch_handler(DMA2, DMA_CH1); + dma_irq_handler(DMA2, DMA_CH1); } void __irq_dma2_channel2(void) { - dispatch_handler(DMA2, DMA_CH2); + dma_irq_handler(DMA2, DMA_CH2); } void __irq_dma2_channel3(void) { - dispatch_handler(DMA2, DMA_CH3); + dma_irq_handler(DMA2, DMA_CH3); } void __irq_dma2_channel4_5(void) { - dispatch_handler(DMA2, DMA_CH4); - dispatch_handler(DMA2, DMA_CH5); + if ((DMA2_BASE->CCR4 & DMA_CCR_EN) && (DMA2_BASE->ISR & DMA_ISR_GIF4)) { + dma_irq_handler(DMA2, DMA_CH4); + } + if ((DMA2_BASE->CCR5 & DMA_CCR_EN) && (DMA2_BASE->ISR & DMA_ISR_GIF5)) { + dma_irq_handler(DMA2, DMA_CH5); + } } #endif diff --git a/libmaple/stm32f1/include/series/dma.h b/libmaple/stm32f1/include/series/dma.h index 60582ea..6da3246 100644 --- a/libmaple/stm32f1/include/series/dma.h +++ b/libmaple/stm32f1/include/series/dma.h @@ -29,7 +29,7 @@ * @file libmaple/stm32f1/include/series/dma.h * @author Marti Bolivar <mbolivar@leaflabs.com>; * Original implementation by Michael Hope - * @brief STM32F1 Direct Memory Access header + * @brief STM32F1 DMA series header. */ /* @@ -44,13 +44,14 @@ extern "C"{ #endif #include <libmaple/libmaple_types.h> +#include <libmaple/dma_common.h> /* - * Register map and base pointers + * Register maps and base pointers */ /** - * @brief DMA register map type. + * @brief STM32F1 DMA register map type. * * Note that DMA controller 2 (register map base pointer DMA2_BASE) * only supports channels 1--5. @@ -100,6 +101,44 @@ typedef struct dma_reg_map { /** DMA controller 2 register map base pointer */ #define DMA2_BASE ((struct dma_reg_map*)0x40020400) +/** + * @brief STM32F1 DMA channel (i.e. tube) register map type. + * Provides access to an individual channel's registers. + * @see dma_tube_regs() + */ +typedef struct dma_tube_reg_map { + __io uint32 CCR; /**< Channel configuration register */ + __io uint32 CNDTR; /**< Channel number of data register */ + __io uint32 CPAR; /**< Channel peripheral address register */ + __io uint32 CMAR; /**< Channel memory address register */ +} dma_tube_reg_map; + +/** DMA1 channel 1 register map base pointer */ +#define DMA1CH1_BASE ((struct dma_tube_reg_map*)0x40020008) +/** DMA1 channel 2 register map base pointer */ +#define DMA1CH2_BASE ((struct dma_tube_reg_map*)0x4002001C) +/** DMA1 channel 3 register map base pointer */ +#define DMA1CH3_BASE ((struct dma_tube_reg_map*)0x40020030) +/** DMA1 channel 4 register map base pointer */ +#define DMA1CH4_BASE ((struct dma_tube_reg_map*)0x40020044) +/** DMA1 channel 5 register map base pointer */ +#define DMA1CH5_BASE ((struct dma_tube_reg_map*)0x40020058) +/** DMA1 channel 6 register map base pointer */ +#define DMA1CH6_BASE ((struct dma_tube_reg_map*)0x4002006C) +/** DMA1 channel 7 register map base pointer */ +#define DMA1CH7_BASE ((struct dma_tube_reg_map*)0x40020080) + +/** DMA2 channel 1 register map base pointer */ +#define DMA2CH1_BASE ((struct dma_tube_reg_map*)0x40020408) +/** DMA2 channel 2 register map base pointer */ +#define DMA2CH2_BASE ((struct dma_tube_reg_map*)0x4002041C) +/** DMA2 channel 3 register map base pointer */ +#define DMA2CH3_BASE ((struct dma_tube_reg_map*)0x40020430) +/** DMA2 channel 4 register map base pointer */ +#define DMA2CH4_BASE ((struct dma_tube_reg_map*)0x40020444) +/** DMA2 channel 5 register map base pointer */ +#define DMA2CH5_BASE ((struct dma_tube_reg_map*)0x40020458) + /* * Register bit definitions */ @@ -263,173 +302,259 @@ typedef struct dma_reg_map { * Devices */ -struct dma_dev; -extern struct dma_dev *DMA1; +extern dma_dev *DMA1; #if defined(STM32_HIGH_DENSITY) || defined(STM32_XL_DENSITY) -extern struct dma_dev *DMA2; +extern dma_dev *DMA2; #endif /* - * Convenience routines. + * Other types needed by, or useful for, <libmaple/dma.h>. */ -/* This hack is due to a circular dependency between us and - * <libmaple/dma.h>. */ -static __always_inline dma_reg_map* _dma_dev_regs(struct dma_dev*); - -/** Flags for DMA transfer configuration. */ -typedef enum dma_mode_flags { - DMA_MEM_2_MEM = 1 << 14, /**< Memory to memory mode */ - DMA_MINC_MODE = 1 << 7, /**< Auto-increment memory address */ - DMA_PINC_MODE = 1 << 6, /**< Auto-increment peripheral address */ - DMA_CIRC_MODE = 1 << 5, /**< Circular mode */ - DMA_FROM_MEM = 1 << 4, /**< Read from memory to peripheral */ - DMA_TRNS_ERR = 1 << 3, /**< Interrupt on transfer error */ - DMA_HALF_TRNS = 1 << 2, /**< Interrupt on half-transfer */ - DMA_TRNS_CMPLT = 1 << 1 /**< Interrupt on transfer completion */ -} dma_mode_flags; - -/** Source and destination transfer sizes. */ -typedef enum dma_xfer_size { - DMA_SIZE_8BITS = 0, /**< 8-bit transfers */ - DMA_SIZE_16BITS = 1, /**< 16-bit transfers */ - DMA_SIZE_32BITS = 2 /**< 32-bit transfers */ -} dma_xfer_size; - -/** DMA channel */ -typedef enum dma_channel { - DMA_CH1 = 1, /**< Channel 1 */ - DMA_CH2 = 2, /**< Channel 2 */ - DMA_CH3 = 3, /**< Channel 3 */ - DMA_CH4 = 4, /**< Channel 4 */ - DMA_CH5 = 5, /**< Channel 5 */ - DMA_CH6 = 6, /**< Channel 6 */ - DMA_CH7 = 7, /**< Channel 7 */ -} dma_channel; - -void dma_setup_transfer(struct dma_dev *dev, - dma_channel channel, - __io void *peripheral_address, - dma_xfer_size peripheral_size, - __io void *memory_address, - dma_xfer_size memory_size, - uint32 mode); - -void dma_set_num_transfers(struct dma_dev *dev, - dma_channel channel, - uint16 num_transfers); - -/** DMA transfer priority. */ -typedef enum dma_priority { - DMA_PRIORITY_LOW = DMA_CCR_PL_LOW, /**< Low priority */ - DMA_PRIORITY_MEDIUM = DMA_CCR_PL_MEDIUM, /**< Medium priority */ - DMA_PRIORITY_HIGH = DMA_CCR_PL_HIGH, /**< High priority */ - DMA_PRIORITY_VERY_HIGH = DMA_CCR_PL_VERY_HIGH /**< Very high priority */ -} dma_priority; - -void dma_set_priority(struct dma_dev *dev, - dma_channel channel, - dma_priority priority); - -void dma_attach_interrupt(struct dma_dev *dev, - dma_channel channel, - void (*handler)(void)); -void dma_detach_interrupt(struct dma_dev *dev, dma_channel channel); - /** - * Encodes the reason why a DMA interrupt was called. - * @see dma_get_irq_cause() + * @brief STM32F1 dma_tube. + * On STM32F1, DMA tubes are just channels. */ -typedef enum dma_irq_cause { - DMA_TRANSFER_COMPLETE, /**< Transfer is complete. */ - DMA_TRANSFER_HALF_COMPLETE, /**< Transfer is half complete. */ - DMA_TRANSFER_ERROR, /**< Error occurred during transfer. */ -} dma_irq_cause; - -dma_irq_cause dma_get_irq_cause(struct dma_dev *dev, dma_channel channel); +#define dma_tube dma_channel -void dma_enable(struct dma_dev *dev, dma_channel channel); -void dma_disable(struct dma_dev *dev, dma_channel channel); - -void dma_set_mem_addr(struct dma_dev *dev, - dma_channel channel, - __io void *address); -void dma_set_per_addr(struct dma_dev *dev, - dma_channel channel, - __io void *address); +/** + * @brief On STM32F1, dma_channel_reg_map is an alias for dma_tube_reg_map. + * This is for backwards compatibility. */ +#define dma_channel_reg_map dma_tube_reg_map /** - * @brief DMA channel register map type. - * - * Provides access to an individual channel's registers. + * @brief STM32F1 configuration flags for dma_tube_config + * @see struct dma_tube_config */ -typedef struct dma_channel_reg_map { - __io uint32 CCR; /**< Channel configuration register */ - __io uint32 CNDTR; /**< Channel number of data register */ - __io uint32 CPAR; /**< Channel peripheral address register */ - __io uint32 CMAR; /**< Channel memory address register */ -} dma_channel_reg_map; - -#define DMA_CHANNEL_NREGS 5 +typedef enum dma_cfg_flags { + /** + * Source address increment mode + * + * If this flag is set, the source address is incremented (by the + * source size) after each DMA transfer. + */ + DMA_CFG_SRC_INC = 1U << 31, + + /** + * Destination address increment mode + * + * If this flag is set, the destination address is incremented (by + * the destination size) after each DMA transfer. + */ + DMA_CFG_DST_INC = 1U << 30, + + /** + * Circular mode + * + * This mode is not available for memory-to-memory transfers. + */ + DMA_CFG_CIRC = DMA_CCR_CIRC, + + /** Transfer complete interrupt enable */ + DMA_CFG_CMPLT_IE = DMA_CCR_TCIE, + /** Transfer half-complete interrupt enable */ + DMA_CFG_HALF_CMPLT_IE = DMA_CCR_HTIE, + /** Transfer error interrupt enable */ + DMA_CFG_ERR_IE = DMA_CCR_TEIE, +} dma_cfg_flags; /** - * @brief Obtain a pointer to an individual DMA channel's registers. + * @brief STM32F1 DMA request sources. + * + * IMPORTANT: * - * For example, dma_channel_regs(DMA1, DMA_CH1)->CCR is DMA1_BASE->CCR1. + * 1. On STM32F1, each dma_request_src can only be used by a + * particular tube on a particular DMA controller. For example, + * DMA_REQ_SRC_ADC1 belongs to DMA1, tube 1. DMA2 cannot serve + * requests from ADC1, nor can DMA1 tube 2, etc. If you try to use a + * request source with the wrong DMA controller or tube on STM32F1, + * dma_tube_cfg() will fail. * - * @param dev DMA device - * @param channel DMA channel whose channel register map to obtain. + * 2. In general, a DMA tube can only serve a single request source at + * a time, and on STM32F1, Terrible Super-Bad Things will happen if + * two request sources are active for a single tube. + * + * To make all this easier to sort out, these dma_request_src + * enumerators are grouped by DMA controller and tube. + * + * @see struct dma_tube_config + * @see dma_tube_cfg() + */ +typedef enum dma_request_src { + /* Each request source encodes the DMA controller and channel it + * belongs to, for error checking in dma_tube_cfg(). */ + + /* DMA1 request sources */ + + /**@{*/ + /** (DMA1, tube 1) */ + DMA_REQ_SRC_ADC1 = (RCC_DMA1 << 3) | 1, + DMA_REQ_SRC_TIM2_CH3 = (RCC_DMA1 << 3) | 1, + DMA_REQ_SRC_TIM4_CH1 = (RCC_DMA1 << 3) | 1, + /**@}*/ + + /**@{*/ + /** (DMA1, tube 2)*/ + DMA_REQ_SRC_SPI1_RX = (RCC_DMA1 << 3) | 2, + DMA_REQ_SRC_USART3_TX = (RCC_DMA1 << 3) | 2, + DMA_REQ_SRC_TIM1_CH1 = (RCC_DMA1 << 3) | 2, + DMA_REQ_SRC_TIM2_UP = (RCC_DMA1 << 3) | 2, + DMA_REQ_SRC_TIM3_CH3 = (RCC_DMA1 << 3) | 2, + /**@}*/ + + /**@{*/ + /** (DMA1, tube 3)*/ + DMA_REQ_SRC_SPI1_TX = (RCC_DMA1 << 3) | 3, + DMA_REQ_SRC_USART3_RX = (RCC_DMA1 << 3) | 3, + DMA_REQ_SRC_TIM1_CH2 = (RCC_DMA1 << 3) | 3, + DMA_REQ_SRC_TIM3_CH4 = (RCC_DMA1 << 3) | 3, + DMA_REQ_SRC_TIM3_UP = (RCC_DMA1 << 3) | 3, + /**@}*/ + + /**@{*/ + /** (DMA1, tube 4)*/ + DMA_REQ_SRC_SPI2_RX = (RCC_DMA1 << 3) | 4, + DMA_REQ_SRC_I2S2_RX = (RCC_DMA1 << 3) | 4, + DMA_REQ_SRC_USART1_TX = (RCC_DMA1 << 3) | 4, + DMA_REQ_SRC_I2C2_TX = (RCC_DMA1 << 3) | 4, + DMA_REQ_SRC_TIM1_CH4 = (RCC_DMA1 << 3) | 4, + DMA_REQ_SRC_TIM1_TRIG = (RCC_DMA1 << 3) | 4, + DMA_REQ_SRC_TIM1_COM = (RCC_DMA1 << 3) | 4, + DMA_REQ_SRC_TIM4_CH2 = (RCC_DMA1 << 3) | 4, + /**@}*/ + + /**@{*/ + /** (DMA1, tube 5)*/ + DMA_REQ_SRC_SPI2_TX = (RCC_DMA1 << 3) | 5, + DMA_REQ_SRC_I2S2_TX = (RCC_DMA1 << 3) | 5, + DMA_REQ_SRC_USART1_RX = (RCC_DMA1 << 3) | 5, + DMA_REQ_SRC_I2C2_RX = (RCC_DMA1 << 3) | 5, + DMA_REQ_SRC_TIM1_UP = (RCC_DMA1 << 3) | 5, + DMA_REQ_SRC_TIM2_CH1 = (RCC_DMA1 << 3) | 5, + DMA_REQ_SRC_TIM4_CH3 = (RCC_DMA1 << 3) | 5, + /**@}*/ + + /**@{*/ + /** (DMA1, tube 6)*/ + DMA_REQ_SRC_USART2_RX = (RCC_DMA1 << 3) | 6, + DMA_REQ_SRC_I2C1_TX = (RCC_DMA1 << 3) | 6, + DMA_REQ_SRC_TIM1_CH3 = (RCC_DMA1 << 3) | 6, + DMA_REQ_SRC_TIM3_CH1 = (RCC_DMA1 << 3) | 6, + DMA_REQ_SRC_TIM3_TRIG = (RCC_DMA1 << 3) | 6, + /**@}*/ + + /**@{*/ + /* Tube 7 */ + DMA_REQ_SRC_USART2_TX = (RCC_DMA1 << 3) | 7, + DMA_REQ_SRC_I2C1_RX = (RCC_DMA1 << 3) | 7, + DMA_REQ_SRC_TIM2_CH2 = (RCC_DMA1 << 3) | 7, + DMA_REQ_SRC_TIM2_CH4 = (RCC_DMA1 << 3) | 7, + DMA_REQ_SRC_TIM4_UP = (RCC_DMA1 << 3) | 7, + /**@}*/ + + /* DMA2 request sources */ + + /**@{*/ + /** (DMA2, tube 1)*/ + DMA_REQ_SRC_SPI3_RX = (RCC_DMA2 << 3) | 1, + DMA_REQ_SRC_I2S3_RX = (RCC_DMA2 << 3) | 1, + DMA_REQ_SRC_TIM5_CH4 = (RCC_DMA2 << 3) | 1, + DMA_REQ_SRC_TIM5_TRIG = (RCC_DMA2 << 3) | 1, + /**@}*/ + + /**@{*/ + /** (DMA2, tube 2)*/ + DMA_REQ_SRC_SPI3_TX = (RCC_DMA2 << 3) | 2, + DMA_REQ_SRC_I2S3_TX = (RCC_DMA2 << 3) | 2, + DMA_REQ_SRC_TIM5_CH3 = (RCC_DMA2 << 3) | 2, + DMA_REQ_SRC_TIM5_UP = (RCC_DMA2 << 3) | 2, + /**@}*/ + + /**@{*/ + /** (DMA2, tube 3)*/ + DMA_REQ_SRC_UART4_RX = (RCC_DMA2 << 3) | 3, + DMA_REQ_SRC_TIM6_UP = (RCC_DMA2 << 3) | 3, + DMA_REQ_SRC_DAC_CH1 = (RCC_DMA2 << 3) | 3, + /**@}*/ + + /**@{*/ + /** (DMA2, tube 4)*/ + DMA_REQ_SRC_SDIO = (RCC_DMA2 << 3) | 4, + DMA_REQ_SRC_TIM5_CH2 = (RCC_DMA2 << 3) | 4, + /**@}*/ + + /**@{*/ + /** (DMA2, tube 5)*/ + DMA_REQ_SRC_ADC3 = (RCC_DMA2 << 3) | 5, + DMA_REQ_SRC_UART4_TX = (RCC_DMA2 << 3) | 5, + DMA_REQ_SRC_TIM5_CH1 = (RCC_DMA2 << 3) | 5, + /**@}*/ +} dma_request_src; + +/* + * Convenience routines. */ -static inline dma_channel_reg_map* dma_channel_regs(struct dma_dev *dev, - dma_channel channel) { - __io uint32 *ccr1 = &_dma_dev_regs(dev)->CCR1; - return (dma_channel_reg_map*)(ccr1 + DMA_CHANNEL_NREGS * (channel - 1)); -} /** - * @brief Check if a DMA channel is enabled - * @param dev DMA device - * @param channel Channel whose enabled bit to check. + * @brief On STM32F1, dma_is_channel_enabled() is an alias for + * dma_is_enabled(). + * This is for backwards compatibility. */ -static inline uint8 dma_is_channel_enabled(struct dma_dev *dev, - dma_channel channel) { - return (uint8)(dma_channel_regs(dev, channel)->CCR & DMA_CCR_EN); +#define dma_is_channel_enabled dma_is_enabled + +#define DMA_CHANNEL_NREGS 5 /* accounts for reserved word */ +static inline dma_tube_reg_map* dma_tube_regs(dma_dev *dev, dma_tube tube) { + __io uint32 *ccr1 = &dev->regs->CCR1; + return (dma_channel_reg_map*)(ccr1 + DMA_CHANNEL_NREGS * (tube - 1)); } /** - * @brief Get the ISR status bits for a DMA channel. - * - * The bits are returned right-aligned, in the following order: - * transfer error flag, half-transfer flag, transfer complete flag, - * global interrupt flag. - * - * If you're attempting to figure out why a DMA interrupt fired; you - * may find dma_get_irq_cause() more convenient. - * - * @param dev DMA device - * @param channel Channel whose ISR bits to return. - * @see dma_get_irq_cause(). - */ -static inline uint8 dma_get_isr_bits(struct dma_dev *dev, - dma_channel channel) { - uint8 shift = (channel - 1) * 4; - return (_dma_dev_regs(dev)->ISR >> shift) & 0xF; + * @brief On STM32F1, dma_channel_regs() is an alias for dma_tube_regs(). + * This is for backwards compatibility. */ +#define dma_channel_regs(dev, ch) dma_tube_regs(dev, ch) + +static inline uint8 dma_is_enabled(dma_dev *dev, dma_tube tube) { + return (uint8)(dma_tube_regs(dev, tube)->CCR & DMA_CCR_EN); +} + +static inline uint8 dma_get_isr_bits(dma_dev *dev, dma_tube tube) { + uint8 shift = (tube - 1) * 4; + return (dev->regs->ISR >> shift) & 0xF; +} + +static inline void dma_clear_isr_bits(dma_dev *dev, dma_tube tube) { + dev->regs->IFCR = (1U << (4 * (tube - 1))); } /** - * @brief Clear the ISR status bits for a given DMA channel. - * - * If you're attempting to clean up after yourself in a DMA interrupt, - * you may find dma_get_irq_cause() more convenient. - * - * @param dev DMA device - * @param channel Channel whose ISR bits to clear. - * @see dma_get_irq_cause() + * @brief Deprecated + * STM32F1 mode flags for dma_setup_xfer(). Use dma_tube_cfg() instead. + * @see dma_tube_cfg() */ -static inline void dma_clear_isr_bits(struct dma_dev *dev, - dma_channel channel) { - _dma_dev_regs(dev)->IFCR = (1U << (4 * (channel - 1))); -} +typedef enum dma_mode_flags { + DMA_MEM_2_MEM = 1 << 14, /**< Memory to memory mode */ + DMA_MINC_MODE = 1 << 7, /**< Auto-increment memory address */ + DMA_PINC_MODE = 1 << 6, /**< Auto-increment peripheral address */ + DMA_CIRC_MODE = 1 << 5, /**< Circular mode */ + DMA_FROM_MEM = 1 << 4, /**< Read from memory to peripheral */ + DMA_TRNS_ERR = 1 << 3, /**< Interrupt on transfer error */ + DMA_HALF_TRNS = 1 << 2, /**< Interrupt on half-transfer */ + DMA_TRNS_CMPLT = 1 << 1 /**< Interrupt on transfer completion */ +} dma_mode_flags; + +/* Keep this around for backwards compatibility, but it's deprecated. + * New code should use dma_tube_cfg() instead. + * + * (It's not possible to fully configure a DMA stream on F2 with just + * this information, so this interface is too tied to the F1.) */ +__deprecated +void dma_setup_transfer(dma_dev *dev, + dma_channel channel, + __io void *peripheral_address, + dma_xfer_size peripheral_size, + __io void *memory_address, + dma_xfer_size memory_size, + uint32 mode); #ifdef __cplusplus } // extern "C" |