diff options
Diffstat (limited to 'libmaple/usb/usb_callbacks.c')
| -rw-r--r-- | libmaple/usb/usb_callbacks.c | 390 |
1 files changed, 194 insertions, 196 deletions
diff --git a/libmaple/usb/usb_callbacks.c b/libmaple/usb/usb_callbacks.c index 4d7e57a..ccb0fdd 100644 --- a/libmaple/usb/usb_callbacks.c +++ b/libmaple/usb/usb_callbacks.c @@ -8,19 +8,19 @@ #include "usb_hardware.h" ONE_DESCRIPTOR Device_Descriptor = { - (uint8*)&usbVcomDescriptor_Device, - sizeof(USB_Descriptor_Device) + (uint8*)&usbVcomDescriptor_Device, + sizeof(USB_Descriptor_Device) }; ONE_DESCRIPTOR Config_Descriptor = { - (uint8*)&usbVcomDescriptor_Config, - 0x43//sizeof(USB_Descriptor_Config) + (uint8*)&usbVcomDescriptor_Config, + 0x43//sizeof(USB_Descriptor_Config) }; ONE_DESCRIPTOR String_Descriptor[3] = { - {(uint8*)&usbVcomDescriptor_LangID, USB_DESCRIPTOR_STRING_LEN(1)}, - {(uint8*)&usbVcomDescriptor_iManufacturer,USB_DESCRIPTOR_STRING_LEN(8)}, - {(uint8*)&usbVcomDescriptor_iProduct, USB_DESCRIPTOR_STRING_LEN(8)} + {(uint8*)&usbVcomDescriptor_LangID, USB_DESCRIPTOR_STRING_LEN(1)}, + {(uint8*)&usbVcomDescriptor_iManufacturer,USB_DESCRIPTOR_STRING_LEN(8)}, + {(uint8*)&usbVcomDescriptor_iProduct, USB_DESCRIPTOR_STRING_LEN(8)} }; uint8 last_request = 0; @@ -42,12 +42,12 @@ RESET_STATE reset_state = DTR_UNSET; uint8 line_dtr_rts = 0; void vcomDataTxCb(void) { - /* do whatever after data has been sent to host */ + /* do whatever after data has been sent to host */ - /* allows usbSendBytes to stop blocking */ + /* allows usbSendBytes to stop blocking */ - - countTx = 0; /* assumes tx transactions are atomic 64 bytes (nearly certain they are) */ + /* assumes tx transactions are atomic 64 bytes (nearly certain they are) */ + countTx = 0; } /* we could get arbitrarily complicated here for speed purposes @@ -64,7 +64,7 @@ void vcomDataRxCb(void) { SetEPRxStatus(VCOM_RX_ENDP,EP_RX_NAK); /* todo, not checking very carefully for edge cases. USUALLY, - if we emit the reset pulse and send 4 bytes, then newBytes + if we emit the reset pulse and send 4 bytes, then newBytes should be 4. But its POSSIBLE that this would be violated in some cases */ @@ -82,253 +82,251 @@ void vcomDataRxCb(void) { int i; USB_Bool cmpMatch = TRUE; for (i=0; i<4; i++) { - if (chkBuf[i] != cmpBuf[i]) { - cmpMatch = FALSE; - } + if (chkBuf[i] != cmpBuf[i]) { + cmpMatch = FALSE; + } } if (cmpMatch) { - asm volatile("mov r0, %[stack_top] \n\t" // Reset the stack - "mov sp, r0 \n\t" - "mov r0, #1 \n\t" - "mov r1, %[target_addr] \n\t" - "mov r2, %[cpsr] \n\t" - "push {r2} \n\t" // Fake xPSR - "push {r1} \n\t" // Target address for PC - "push {r0} \n\t" // Fake LR - "push {r0} \n\t" // Fake R12 - "push {r0} \n\t" // Fake R3 - "push {r0} \n\t" // Fake R2 - "push {r0} \n\t" // Fake R1 - "push {r0} \n\t" // Fake R0 - "mov lr, %[exc_return] \n\t" - "bx lr" - : - : [stack_top] "r" (STACK_TOP), - [target_addr] "r" (target), - [exc_return] "r" (EXC_RETURN), - [cpsr] "r" (DEFAULT_CPSR) - : "r0", "r1", "r2"); - /* should never get here */ + asm volatile("mov r0, %[stack_top] \n\t" // Reset the stack + "mov sp, r0 \n\t" + "mov r0, #1 \n\t" + "mov r1, %[target_addr] \n\t" + "mov r2, %[cpsr] \n\t" + "push {r2} \n\t" // Fake xPSR + "push {r1} \n\t" // Target address for PC + "push {r0} \n\t" // Fake LR + "push {r0} \n\t" // Fake R12 + "push {r0} \n\t" // Fake R3 + "push {r0} \n\t" // Fake R2 + "push {r0} \n\t" // Fake R1 + "push {r0} \n\t" // Fake R0 + "mov lr, %[exc_return] \n\t" + "bx lr" + : + : [stack_top] "r" (STACK_TOP), + [target_addr] "r" (target), + [exc_return] "r" (EXC_RETURN), + [cpsr] "r" (DEFAULT_CPSR) + : "r0", "r1", "r2"); + /* should never get here */ } } } - - PMAToUserBufferCopy(&vcomBufferRx[0],VCOM_RX_ADDR,newBytes); } void vcomManagementCb(void) { -/* unused. This enpoint would callback if we had sent a linestate - changed notification */ + /* unused. This enpoint would callback if we had sent a linestate + changed notification */ } u8* vcomGetSetLineCoding(uint16 length) { - if (length == 0) { - pInformation->Ctrl_Info.Usb_wLength = sizeof(USB_Line_Coding); - } - return (uint8*)&line_coding; + if (length == 0) { + pInformation->Ctrl_Info.Usb_wLength = sizeof(USB_Line_Coding); + } + return (uint8*)&line_coding; } vcomSetLineState(void) { } void usbInit(void) { - pInformation->Current_Configuration = 0; - usbPowerOn(); + pInformation->Current_Configuration = 0; + usbPowerOn(); - _SetISTR(0); - wInterrupt_Mask = ISR_MSK; - _SetCNTR(wInterrupt_Mask); + _SetISTR(0); + wInterrupt_Mask = ISR_MSK; + _SetCNTR(wInterrupt_Mask); - usbEnbISR(); - bDeviceState = UNCONNECTED; + usbEnbISR(); + bDeviceState = UNCONNECTED; } void usbReset(void) { - pInformation->Current_Configuration = 0; - - /* current feature is current bmAttributes */ - pInformation->Current_Feature = (USB_CONFIG_ATTR_BUSPOWERED | USB_CONFIG_ATTR_SELF_POWERED); - - _SetBTABLE(USB_BTABLE_ADDRESS); - - /* setup control endpoint 0 */ - _SetEPType(ENDP0, EP_CONTROL); - _SetEPTxStatus(ENDP0, EP_TX_STALL); - _SetEPRxAddr(ENDP0,VCOM_CTRL_RX_ADDR); - _SetEPTxAddr(ENDP0,VCOM_CTRL_TX_ADDR); - Clear_Status_Out(ENDP0); - - SetEPRxCount(ENDP0, pProperty->MaxPacketSize); - SetEPRxValid(ENDP0); - - /* setup management endpoint 1 */ - SetEPType (VCOM_NOTIFICATION_ENDP, EP_INTERRUPT); - SetEPTxAddr (VCOM_NOTIFICATION_ENDP, VCOM_NOTIFICATION_ADDR); - SetEPTxStatus (VCOM_NOTIFICATION_ENDP, EP_TX_NAK); - SetEPRxStatus (VCOM_NOTIFICATION_ENDP, EP_RX_DIS); - - /* setup data endpoint OUT (rx) */ -/* SetEPType (VCOM_RX_ENDP, EP_BULK); */ -/* SetEPRxAddr (VCOM_RX_ENDP, VCOM_RX_ADDR); */ -/* SetEPRxCount (VCOM_RX_ENDP, VCOM_RX_EPSIZE); */ -/* // SetEPTxStatus (VCOM_RX_ENDP, EP_TX_DIS); */ -/* SetEPRxStatus (VCOM_RX_ENDP, EP_RX_VALID); */ - - SetEPType (3, EP_BULK); - SetEPRxAddr (3, 0x110); - SetEPRxCount (3,64); - // SetEPTxStatus (VCOM_RX_ENDP, EP_TX_DIS); - SetEPRxStatus (3, EP_RX_VALID); - - /* setup data endpoint IN (tx) */ - SetEPType (VCOM_TX_ENDP, EP_BULK); - SetEPTxAddr (VCOM_TX_ENDP, VCOM_TX_ADDR); - SetEPTxStatus (VCOM_TX_ENDP, EP_TX_NAK); - SetEPRxStatus (VCOM_TX_ENDP, EP_RX_DIS); - - bDeviceState = ATTACHED; - SetDeviceAddress(0); - - /* reset the rx fifo */ - recvBufIn = 0; - recvBufOut = 0; - maxNewBytes = VCOM_RX_EPSIZE; - countTx = 0; + pInformation->Current_Configuration = 0; + + /* current feature is current bmAttributes */ + pInformation->Current_Feature = (USB_CONFIG_ATTR_BUSPOWERED | USB_CONFIG_ATTR_SELF_POWERED); + + _SetBTABLE(USB_BTABLE_ADDRESS); + + /* setup control endpoint 0 */ + _SetEPType(ENDP0, EP_CONTROL); + _SetEPTxStatus(ENDP0, EP_TX_STALL); + _SetEPRxAddr(ENDP0,VCOM_CTRL_RX_ADDR); + _SetEPTxAddr(ENDP0,VCOM_CTRL_TX_ADDR); + Clear_Status_Out(ENDP0); + + SetEPRxCount(ENDP0, pProperty->MaxPacketSize); + SetEPRxValid(ENDP0); + + /* setup management endpoint 1 */ + SetEPType (VCOM_NOTIFICATION_ENDP, EP_INTERRUPT); + SetEPTxAddr (VCOM_NOTIFICATION_ENDP, VCOM_NOTIFICATION_ADDR); + SetEPTxStatus (VCOM_NOTIFICATION_ENDP, EP_TX_NAK); + SetEPRxStatus (VCOM_NOTIFICATION_ENDP, EP_RX_DIS); + + /* setup data endpoint OUT (rx) */ + /* SetEPType (VCOM_RX_ENDP, EP_BULK); */ + /* SetEPRxAddr (VCOM_RX_ENDP, VCOM_RX_ADDR); */ + /* SetEPRxCount (VCOM_RX_ENDP, VCOM_RX_EPSIZE); */ + /* // SetEPTxStatus (VCOM_RX_ENDP, EP_TX_DIS); */ + /* SetEPRxStatus (VCOM_RX_ENDP, EP_RX_VALID); */ + + SetEPType (3, EP_BULK); + SetEPRxAddr (3, 0x110); + SetEPRxCount (3,64); + // SetEPTxStatus (VCOM_RX_ENDP, EP_TX_DIS); + SetEPRxStatus (3, EP_RX_VALID); + + /* setup data endpoint IN (tx) */ + SetEPType (VCOM_TX_ENDP, EP_BULK); + SetEPTxAddr (VCOM_TX_ENDP, VCOM_TX_ADDR); + SetEPTxStatus (VCOM_TX_ENDP, EP_TX_NAK); + SetEPRxStatus (VCOM_TX_ENDP, EP_RX_DIS); + + bDeviceState = ATTACHED; + SetDeviceAddress(0); + + /* reset the rx fifo */ + recvBufIn = 0; + recvBufOut = 0; + maxNewBytes = VCOM_RX_EPSIZE; + countTx = 0; } void usbStatusIn(void) { - /* adjust the usart line coding - if we wish to couple the CDC line coding - with the real usart port */ + /* adjust the usart line coding + if we wish to couple the CDC line coding + with the real usart port */ } void usbStatusOut(void) { } RESULT usbDataSetup(uint8 request) { - uint8 *(*CopyRoutine)(uint16); - CopyRoutine = NULL; - - if (Type_Recipient == (CLASS_REQUEST | INTERFACE_RECIPIENT)) { - switch (request) { - case (GET_LINE_CODING): - CopyRoutine = vcomGetSetLineCoding; - last_request = GET_LINE_CODING; - break; - case (SET_LINE_CODING): - CopyRoutine = vcomGetSetLineCoding; - last_request = SET_LINE_CODING; - break; - default: break; + uint8 *(*CopyRoutine)(uint16); + CopyRoutine = NULL; + + if (Type_Recipient == (CLASS_REQUEST | INTERFACE_RECIPIENT)) { + switch (request) { + case (GET_LINE_CODING): + CopyRoutine = vcomGetSetLineCoding; + last_request = GET_LINE_CODING; + break; + case (SET_LINE_CODING): + CopyRoutine = vcomGetSetLineCoding; + last_request = SET_LINE_CODING; + break; + default: break; + } } - } - if (CopyRoutine == NULL) { - return USB_UNSUPPORT; - } + if (CopyRoutine == NULL) { + return USB_UNSUPPORT; + } - pInformation->Ctrl_Info.CopyData = CopyRoutine; - pInformation->Ctrl_Info.Usb_wOffset = 0; - (*CopyRoutine)(0); - return USB_SUCCESS; + pInformation->Ctrl_Info.CopyData = CopyRoutine; + pInformation->Ctrl_Info.Usb_wOffset = 0; + (*CopyRoutine)(0); + return USB_SUCCESS; } RESULT usbNoDataSetup(u8 request) { - uint8 new_signal; - - /* we support set com feature but dont handle it */ - if (Type_Recipient == (CLASS_REQUEST | INTERFACE_RECIPIENT)) { - - switch (request) { - case (SET_COMM_FEATURE): - return USB_SUCCESS; - case (SET_CONTROL_LINE_STATE): - /* to reset the board, pull both dtr and rts low - then pulse dtr by itself */ - new_signal = pInformation->USBwValues.bw.bb0 & (CONTROL_LINE_DTR | CONTROL_LINE_RTS); - line_dtr_rts = new_signal & 0x03; - - switch (reset_state) { - /* no default, covered enum */ - case DTR_UNSET: - if ((new_signal & CONTROL_LINE_DTR) == 0 ) { - reset_state = DTR_LOW; - } else { - reset_state = DTR_HIGH; - } - break; - - case DTR_HIGH: - if ((new_signal & CONTROL_LINE_DTR) == 0 ) { - reset_state = DTR_NEGEDGE; - } else { - reset_state = DTR_HIGH; - } - break; - - case DTR_NEGEDGE: - if ((new_signal & CONTROL_LINE_DTR) == 0 ) { - reset_state = DTR_LOW; - } else { - reset_state = DTR_HIGH; - } - break; - - case DTR_LOW: - if ((new_signal & CONTROL_LINE_DTR) == 0 ) { - reset_state = DTR_LOW; - } else { - reset_state = DTR_HIGH; - } - break; - } - - return USB_SUCCESS; + uint8 new_signal; + + /* we support set com feature but dont handle it */ + if (Type_Recipient == (CLASS_REQUEST | INTERFACE_RECIPIENT)) { + + switch (request) { + case (SET_COMM_FEATURE): + return USB_SUCCESS; + case (SET_CONTROL_LINE_STATE): + /* to reset the board, pull both dtr and rts low + then pulse dtr by itself */ + new_signal = pInformation->USBwValues.bw.bb0 & (CONTROL_LINE_DTR | CONTROL_LINE_RTS); + line_dtr_rts = new_signal & 0x03; + + switch (reset_state) { + /* no default, covered enum */ + case DTR_UNSET: + if ((new_signal & CONTROL_LINE_DTR) == 0 ) { + reset_state = DTR_LOW; + } else { + reset_state = DTR_HIGH; + } + break; + + case DTR_HIGH: + if ((new_signal & CONTROL_LINE_DTR) == 0 ) { + reset_state = DTR_NEGEDGE; + } else { + reset_state = DTR_HIGH; + } + break; + + case DTR_NEGEDGE: + if ((new_signal & CONTROL_LINE_DTR) == 0 ) { + reset_state = DTR_LOW; + } else { + reset_state = DTR_HIGH; + } + break; + + case DTR_LOW: + if ((new_signal & CONTROL_LINE_DTR) == 0 ) { + reset_state = DTR_LOW; + } else { + reset_state = DTR_HIGH; + } + break; + } + + return USB_SUCCESS; + } } - } - return USB_UNSUPPORT; + return USB_UNSUPPORT; } RESULT usbGetInterfaceSetting(uint8 interface, uint8 alt_setting) { - if (alt_setting > 0) { - return USB_UNSUPPORT; - } else if (interface > 1) { - return USB_UNSUPPORT; - } + if (alt_setting > 0) { + return USB_UNSUPPORT; + } else if (interface > 1) { + return USB_UNSUPPORT; + } - return USB_SUCCESS; + return USB_SUCCESS; } u8* usbGetDeviceDescriptor(u16 length) { - return Standard_GetDescriptorData(length, &Device_Descriptor); + return Standard_GetDescriptorData(length, &Device_Descriptor); } u8* usbGetConfigDescriptor(u16 length) { - return Standard_GetDescriptorData(length, &Config_Descriptor); + return Standard_GetDescriptorData(length, &Config_Descriptor); } u8* usbGetStringDescriptor(u16 length) { - uint8 wValue0 = pInformation->USBwValue0; + uint8 wValue0 = pInformation->USBwValue0; - if (wValue0 > 2) { - return NULL; - } - return Standard_GetDescriptorData(length, &String_Descriptor[wValue0]); + if (wValue0 > 2) { + return NULL; + } + return Standard_GetDescriptorData(length, &String_Descriptor[wValue0]); } /* internal callbacks to respond to standard requests */ void usbSetConfiguration(void) { - if (pInformation->Current_Configuration != 0) { - bDeviceState = CONFIGURED; - } + if (pInformation->Current_Configuration != 0) { + bDeviceState = CONFIGURED; + } } void usbSetDeviceAddress(void) { - bDeviceState = ADDRESSED; + bDeviceState = ADDRESSED; } |