diff options
Diffstat (limited to 'docs/source/libmaple/overview.rst')
-rw-r--r-- | docs/source/libmaple/overview.rst | 516 |
1 files changed, 516 insertions, 0 deletions
diff --git a/docs/source/libmaple/overview.rst b/docs/source/libmaple/overview.rst new file mode 100644 index 0000000..006f1d8 --- /dev/null +++ b/docs/source/libmaple/overview.rst @@ -0,0 +1,516 @@ +.. highlight:: c + +.. _libmaple-overview: + +Overview +======== + +This page is a general overview of :ref:`libmaple proper +<libmaple-vs-wirish>`. It describes libmaple's design, and names +implementation patterns to look for when using it. General +familiarity with the :ref:`STM32 <stm32>` is assumed; beginners should +start with the high-level :ref:`Wirish interface <language>` instead. +Examples are given from libmaple's sources. + +.. contents:: Contents + :local: + +Design Goals +------------ + +The central goal for libmaple proper is to provide a pleasant, +portable, and consistent set of interfaces for dealing with the +various series of STM32 microcontrollers. + +Portability in particular can be a problem when programming for the +STM32. While the various STM32 series are largely pin-compatible with +one another, the peripheral register maps between series often change +drastically, even when the functionality provided by the peripheral +doesn't change very much. This means that code which accesses +registers directly often needs to change when porting a program to a +different series MCU. + +ST's solution to this problem thus far has been to `issue +<http://www.st.com/internet/com/SOFTWARE_RESOURCES/SW_COMPONENT/FIRMWARE/stm32l1_stdperiph_lib.zip>`_ +`separate +<http://www.st.com/internet/com/SOFTWARE_RESOURCES/SW_COMPONENT/FIRMWARE/stm32f10x_stdperiph_lib.zip>`_ +`firmware +<http://www.st.com/internet/com/SOFTWARE_RESOURCES/SW_COMPONENT/FIRMWARE/stm32f2xx_stdperiph_lib.zip>`_ +`libraries +<http://www.st.com/internet/com/SOFTWARE_RESOURCES/SW_COMPONENT/FIRMWARE/stm32f4_dsp_stdperiph_lib.zip>`_; +one for each STM32 series. Along with these, they have released a +`number +<http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/APPLICATION_NOTE/DM00024853.pdf>`_ +of `application +<http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/APPLICATION_NOTE/DM00033267.pdf>`_ +`notes +<http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/APPLICATION_NOTE/DM00032987.pdf>`_ +describing the compatibility issues and how to migrate between series +by switching firmware libraries. Often, the migration advice is +essentially "rewrite your code"; this occurs, for example, with any +code involving GPIO or DMA being migrated between STM32F1 and STM32F2. + +Needless to say, this can be very annoying. (Didn't we solve this +sort of problem years ago?) When you just want your robot to fly, +your `LEDs to blink <http://www.youtube.com/watch?v=J845L45zqfk>`_, or +your `FM synthesizer <https://github.com/Ixox/preen>`_ to, well, +`synthesize <http://xhosxe.free.fr/IxoxFMSynth.mp3>`_, you probably +couldn't care less about dealing with a new set of registers. + +We want to make it easier to write portable STM32 code. To enable +that, libmaple abstracts away many hardware details behind portable +interfaces. We also want to make it easy for you to get your hands +dirty when need or desire arises. To that end, libmaple makes as few +assumptions as possible, and does its best to get out of your way when +you want it to leave. + +.. _libmaple-overview-devices: + +Libmaple's Device Model +----------------------- + +The libmaple device model is simple and stupid. This is a feature. + +*Device types* are the central libmaple abstraction; they exist to +provide portable interfaces to common peripherals, but they still let +you do nonportable things easily if you want to. + +The rules for device types are: + +- Device types are structs representing peripherals. The name of the + device type for peripheral "foo" is ``struct foo_dev`` (so for + foo=ADC, it's ``struct adc_dev``. For foo=DMA, it's ``struct + dma_dev``; etc.). These are always ``typedef``\ ed to ``foo_dev``. + +- Each device type contains any information needed or used by libmaple + for operating on the peripheral the type represents. Device types + are defined alongside declarations for portable support routines in + the header ``<libmaple/foo.h>`` (examples: :ref:`libmaple-adc`, + :ref:`libmaple-dma`). + +- Direct :ref:`register access <libmaple-overview-regmaps>` is + possible via the ``regs`` field in each device type. (Given a + ``foo_dev *foo``, you can read and write the BAR register + ``FOO_BAR`` with ``foo->regs->BAR``.) + +- An :ref:`rcc_clk_id <libmaple-rcc-rcc_clk_id>` for the device is + available in the ``clk_id`` field; this is an opaque type that can + be used to uniquely identifies the peripheral. (Given ``foo_dev + *foo``, you can check which foo you have by looking at + ``foo->clk_id``.) + +- The backend for each supported STM32 series statically initializes + devices as appropriate, and ensures that the peripheral support + header includes declarations for pointers to these statically + allocated devices. + +- Peripheral support functions usually expect a pointer to a device as + their first argument. These functions' implementations may vary + with the particular microcontroller you're targeting, but their + semantics try to stay the same. To migrate to a different target, + you'll often be able to simply recompile your program (and libmaple) + for the new target. + +- When complete portability is not possible, libmaple tries to keep + the nonportable bits in data, rather than code. + +Example: ``adc_dev`` +~~~~~~~~~~~~~~~~~~~~ + +These rules are best explained by example. The device type for ADC +peripherals is ``struct adc_dev``. Its definition is provided by +``<libmaple/adc.h>``:: + + typedef struct adc_dev { + adc_reg_map *regs; + rcc_clk_id clk_id; + } adc_dev; + +An ``adc_dev`` contains a pointer to its register map in the ``regs`` +field. This ``regs`` field is available on all device types. Its value +is a :ref:`register map base pointer +<libmaple-overview-regmaps-base-pts>` (like ``ADC1_BASE``, etc.) for +the peripheral, as determined by the current target. For example, two +equivalent expressions for reading the ADC1 regular data register are +``ADC1_BASE->DR`` and ``ADC1->regs->DR`` (though the first one is +faster). Manipulating registers directly via ``->regs`` is thus +always possible, but can be nonportable, and should you choose to do +this, it's up to you to get it right. + +An ``adc_dev`` also contains an ``rcc_clk_id`` for the ADC peripheral +it represents in the ``clk_id`` field. The ``rcc_clk_id`` enum type +has an enumerator for each peripheral supported by your series. For +example, the ADC peripherals' ``rcc_clk_id`` enumerators are +``RCC_ADC1``, ``RCC_ADC2``, and ``RCC_ADC3``. In general, an +``rcc_clk_id`` is useful not only for managing the clock line to a +peripheral, but also as a unique identifier for that peripheral. + +(Device types can be more complicated than this; ``adc_dev`` was +chosen as a simple example of the minimum you can expect.) + +Rather than have you define your own ``adc_dev``\ s, libmaple defines +them for you as appropriate for your target STM32 series. For example, +on STM32F1, the file libmaple/stm32f1/adc.c contains the following:: + + static adc_dev adc1 = { + .regs = ADC1_BASE, + .clk_id = RCC_ADC1, + }; + /** ADC1 device. */ + const adc_dev *ADC1 = &adc1; + + static adc_dev adc2 = { + .regs = ADC2_BASE, + .clk_id = RCC_ADC2, + }; + /** ADC2 device. */ + const adc_dev *ADC2 = &adc2; + + #if defined(STM32_HIGH_DENSITY) || defined(STM32_XL_DENSITY) + static adc_dev adc3 = { + .regs = ADC3_BASE, + .clk_id = RCC_ADC3, + }; + /** ADC3 device. */ + const adc_dev *ADC3 = &adc3; + #endif + +Since all supported STM32F1 targets support ADC1 and ADC2, libmaple +predefines corresponding ``adc_dev`` instances for you. To save space, +it avoids defining an ``adc_dev`` for ADC3 unless you are targeting a +high- or XL-density STM32F1, as medium- and lower density MCUs don't +have ADC3. + +Note that the structs themselves are static and are exposed only via +pointers. These pointers are declared in a series-specific ADC +header, ``<series/adc.h>`` which is included by ``<libmaple/adc.h>`` +based on the MCU you're targeting. (**Never include <series/foo.h> +directly**. Instead, include ``<libmaple/foo.h>`` and let it take +care of that for you.) On STM32F1, the series ADC header contains the +following:: + + extern const struct adc_dev *ADC1; + extern const struct adc_dev *ADC2; + #if defined(STM32_HIGH_DENSITY) || defined(STM32_XL_DENSITY) + extern const struct adc_dev *ADC3; + #endif + +In general, you access the predefined devices via these pointers. As +illustrated by the ADC example, the variables for these pointers +follow the naming scheme used in ST's reference manuals -- the pointer +to ADC1's ``adc_dev`` is named ``ADC1``, and so on. + +The :ref:`API documentation <libmaple-apis>` for the peripherals +you're interested in will list the available devices on each target. + +Using Devices +~~~~~~~~~~~~~ + +Peripheral support routines usually expect pointers to their device +types as their first arguments. Here are some ADC examples:: + + uint16 adc_read(const adc_dev *dev, uint8 channel); + static inline void adc_enable(const adc_dev *dev); + static inline void adc_disable(const adc_dev *dev); + +So, to read channel 2 of ADC1, you could call ``adc_read(ADC1, 2)``. +To disable ADC2, call ``adc_disable(ADC2)``; etc. + +That's it; there's nothing complicated here. In general, just follow +links from the :ref:`libmaple-apis` page to the header for the +peripheral you're interested in. It will explain the supported +functionality, both portable and series-specific. + +Segregating Non-portable Functionality into Data +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +As mentioned previously, when total portability isn't possible, +libmaple tries to do the right thing and segregate the nonportable +portions into data rather than code. The function +``adc_set_sample_rate()`` is a good example of how this works, and why +it's useful:: + + void adc_set_sample_rate(const adc_dev *dev, adc_smp_rate smp_rate); + +For example, while both STM32F1 and STM32F2 support setting the ADC +sample time via the same register interface, the actual sample times +supported are different. For instance, on STM32F1, available sample +times include 1.5, 7.5, and 13.5 ADC cycles. On STM32F2, none of these +are available, but 3, 15, and 28 ADC cycles are supported (which is +not true for STM32F1). To work with this, libmaple provides a single +function, ``adc_set_sample_rate()``, for setting an ADC controller's +channel sampling time, but the actual sample rates it takes are given +by the ``adc_smp_rate`` type, which is different on STM32F1 and +STM32F2. + +This is the STM32F1 implementation of adc_smp_rate:: + + typedef enum adc_smp_rate { + ADC_SMPR_1_5, /**< 1.5 ADC cycles */ + ADC_SMPR_7_5, /**< 7.5 ADC cycles */ + ADC_SMPR_13_5, /**< 13.5 ADC cycles */ + ADC_SMPR_28_5, /**< 28.5 ADC cycles */ + ADC_SMPR_41_5, /**< 41.5 ADC cycles */ + ADC_SMPR_55_5, /**< 55.5 ADC cycles */ + ADC_SMPR_71_5, /**< 71.5 ADC cycles */ + ADC_SMPR_239_5, /**< 239.5 ADC cycles */ + } adc_smp_rate; + +And here is the STM32F2 implementation:: + + typedef enum adc_smp_rate { + ADC_SMPR_3, /**< 3 ADC cycles */ + ADC_SMPR_15, /**< 15 ADC cycles */ + ADC_SMPR_28, /**< 28 ADC cycles */ + ADC_SMPR_56, /**< 56 ADC cycles */ + ADC_SMPR_84, /**< 84 ADC cycles */ + ADC_SMPR_112, /**< 112 ADC cycles */ + ADC_SMPR_144, /**< 144 ADC cycles */ + ADC_SMPR_480, /**< 480 ADC cycles */ + } adc_smp_rate; + +So, on F1, you could call ``adc_set_sample_rate(ADC1, ADC_SMPR_1_5)``, +and on F2, you could call ``adc_set_sample_rate(ADC1, +ADC_SMPR_3)``. If you're only interested in one of those series, then +that's all you need to know. + +However, if you're targeting multiple series, then this is useful +because it lets you put the actual sample time for the MCU you're +targeting into a variable (or macro, etc.), whose value depends on the +target you're compiling for. This lets you have a single codebase to +test and maintain, and lets you add support for a new target by simply +adding some new data. + +To continue the example, one easy way is to pick an ``adc_smp_rate`` +for each of STM32F1 and STM32F2 is with conditional compilation. Using +the :ref:`STM32_MCU_SERIES <libmaple-stm32-STM32_MCU_SERIES>` define +from :ref:`libmaple-stm32`, you can write:: + + #include <libmaple/adc.h> + #include <libmaple/stm32.h> + + #if STM32_MCU_SERIES == STM32_SERIES_F1 + /* Target is an STM32F1 */ + adc_smp_rate smp_rate = ADC_SMPR_1_5; + #elif STM32_MCU_SERIES == STM32_SERIES_F2 + /* Target is an STM32F2 */ + adc_smp_rate smp_rate = ADC_SMPR_3; + #else + #error "Unsupported STM32 target; can't pick a sample rate" + #endif + + void setup(void) { + adc_set_smp_rate(ADC1, smp_rate); + } + +Adding support for e.g. STM32F4 would only require adding a new +``#elif`` for that series. This is simple, but hackish, and can get +out of control if you're not careful. + +Another way to get the job done is to declare an ``extern adc_smp_rate +smp_rate``, and use the build system to compile a file defining +``smp_rate`` depending on your target. As was discussed earlier, this +is what libmaple does when choosing which files to use for defining +the appropriate ``adc_dev``\ s for your target. How to do this is +outside the scope of this overview, however. + +.. _libmaple-overview-regmaps: + +Register Maps +------------- + +Though we aim to enable libmaple's users to interact with the more +portable :ref:`device interface <libmaple-overview-devices>` as much +as possible, there will always be a need for efficient direct register +access. To allow for that, libmaple provides *register maps* as a +consistent set of names and abstractions for dealing with peripheral +registers and their bits. + +A *register map type* is a struct which names and provides access to a +peripheral's registers (we can use a struct because registers are +usually mapped into contiguous regions of memory). Here's an example +register map for the DAC peripheral on STM32F1 series MCUs (``__io`` +is just libmaple's way of saying ``volatile`` when referring to +register values):: + + typedef struct dac_reg_map { + __io uint32 CR; /**< Control register */ + __io uint32 SWTRIGR; /**< Software trigger register */ + __io uint32 DHR12R1; /**< Channel 1 12-bit right-aligned data + holding register */ + __io uint32 DHR12L1; /**< Channel 1 12-bit left-aligned data + holding register */ + __io uint32 DHR8R1; /**< Channel 1 8-bit left-aligned data + holding register */ + __io uint32 DHR12R2; /**< Channel 2 12-bit right-aligned data + holding register */ + __io uint32 DHR12L2; /**< Channel 2 12-bit left-aligned data + holding register */ + __io uint32 DHR8R2; /**< Channel 2 8-bit left-aligned data + holding register */ + __io uint32 DHR12RD; /**< Dual DAC 12-bit right-aligned data + holding register */ + __io uint32 DHR12LD; /**< Dual DAC 12-bit left-aligned data + holding register */ + __io uint32 DHR8RD; /**< Dual DAC 8-bit right-aligned data holding + register */ + __io uint32 DOR1; /**< Channel 1 data output register */ + __io uint32 DOR2; /**< Channel 2 data output register */ + } dac_reg_map; + +There are two things to notice here. First, if the chip reference +manual (for STM32F1, that's RM0008) names a register ``DAC_FOO``, then +``dac_reg_map`` has a field named ``FOO``. So, the Channel 1 12-bit +right-aligned data register (DAC_DHR12R1) is the ``DHR12R1`` field in +a ``dac_reg_map``. Second, if the reference manual describes a +register as "Foo bar register", the documentation for the +corresponding field has the same description. This consistency makes +it easy to search for a particular register, and, if you see one used +in a source file, to feel sure about what's going on just based on its +name. + +.. _libmaple-overview-regmaps-base-pts: + +So let's say you've included ``<libmaple/foo.h>``, and you want to +mess with some particular register. You'll do this using *register map +base pointers*, which are pointers to ``struct foo_reg_map``. What's +the name of the base pointer you want? That depends on if there's +more than one foo or not. If there's only one foo, then libmaple +guarantees there will be a ``#define`` that looks like like this:: + + #define FOO_BASE ((struct foo_reg_map*)0xDEADBEEF) + +That is, you're guaranteed there will be a pointer to the (only) +``foo_reg_map`` you want, and it will be called +``FOO_BASE``. (``0xDEADBEEF`` is the register map's *base address*, or +the fixed location in memory where the register map begins). Here's +an example for STM32F1:: + + #define DAC_BASE ((struct dac_reg_map*)0x40007400) + +Here are some examples for how to read and write to registers using +register map base pointers. + +* In order to write 2048 to the channel 1 12-bit left-aligned data + holding register (DAC_DHR12L1), you would write:: + + DAC_BASE->DHR12L1 = 2048; + +* In order to read the DAC control register, you would write:: + + uint32 cr = DAC_BASE->CR; + +That covers the case where there's a single foo peripheral. If +there's more than one (say, if there are *n*), then +``<libmaple/foo.h>`` provides the following:: + + #define FOO1_BASE ((struct foo_reg_map*)0xDEADBEEF) + #define FOO2_BASE ((struct foo_reg_map*)0xF00DF00D) + ... + #define FOOn_BASE ((struct foo_reg_map*)0x1EAF1AB5) + +Here are some examples for the ADCs on STM32F1:: + + #define ADC1_BASE ((struct adc_reg_map*)0x40012400) + #define ADC2_BASE ((struct adc_reg_map*)0x40012800) + +In order to read from the ADC1's regular data register (where the +results of ADC conversion are stored), you would write:: + + uint32 converted_result = ADC1_BASE->DR; + +Register Bit Definitions +------------------------ + +In ``<libmaple/foo.h>``, there will also be a variety of ``#define``\ +s for dealing with interesting bits in the xxx registers, called +*register bit definitions*. In keeping with the ST reference manuals, +these are named according to the scheme ``FOO_REG_FIELD``, where +"``REG``" refers to the register, and "``FIELD``" refers to the bit or +bits in ``REG`` that are special. + +Again, this is probably best explained by example. On STM32F1, each +Direct Memory Access (DMA) controller's register map has a certain +number of channel configuration registers (DMA_CCRx). In each of +these channel configuration registers, bit 14 is called the +``MEM2MEM`` bit, and bits 13 and 12 are the priority level (``PL``) +bits. Here are the register bit definitions for those fields on +STM32F1:: + + #define DMA_CCR_MEM2MEM_BIT 14 + #define DMA_CCR_MEM2MEM (1U << DMA_CCR_MEM2MEM_BIT) + #define DMA_CCR_PL (0x3 << 12) + #define DMA_CCR_PL_LOW (0x0 << 12) + #define DMA_CCR_PL_MEDIUM (0x1 << 12) + #define DMA_CCR_PL_HIGH (0x2 << 12) + #define DMA_CCR_PL_VERY_HIGH (0x3 << 12) + +Thus, to check if the ``MEM2MEM`` bit is set in DMA controller 1's +channel configuration register 2 (DMA_CCR2), you can write:: + + if (DMA1_BASE->CCR2 & DMA_CCR_MEM2MEM) { + /* MEM2MEM is set */ + } + +Certain register values occupy multiple bits. For example, the +priority level (PL) of a DMA channel is determined by bits 13 and 12 +of the corresponding channel configuration register. As shown above, +libmaple provides several register bit definitions for masking out the +individual PL bits and determining their meaning. For example, to set +the priority level of a DMA transfer to "high priority", you can +do a read-modify-write sequence on the DMA_CCR_PL bits like so:: + + uint32 ccr = DMA1_BASE->CCR2; + ccr &= ~DMA_CCR_PL; + ccr |= DMA_CCR_PL_HIGH; + DMA1_BASE->CCR2 = ccr; + +Of course, before doing that, you should check to make sure there's +not already a device-level function for performing the same task! (In +this case, there is. It's called :c:func:`dma_set_priority()`; see +:ref:`libmaple-dma`.) For instance, **none of the above code is +portable** to STM32F4, which uses DMA streams instead of channels for +this purpose. + +Peripheral Support Routines +--------------------------- + +This section describes patterns to look for in peripheral support +routines. + +In general, each device needs to be initialized before it can be used. +libmaple provides this initialization routine for each peripheral +``foo``; its name is ``foo_init()``. These initialization routines +turn on the clock to a device, and restore its register values to +their default settings. Here are a few examples:: + + /* From <libmaple/dma.h> */ + void dma_init(dma_dev *dev); + + /* From <libmaple/gpio.h> */ + void gpio_init(gpio_dev *dev); + void gpio_init_all(void); + +Note that, sometimes, there will be an additional initialization +routine for all available peripherals of a certain kind. + +Many peripherals also need additional configuration before they can be +used. These functions are usually called something along the lines of +``foo_enable()``, and often take additional arguments which specify a +particular configuration for the peripheral. Some examples:: + + /* From <libmaple/usart.h> */ + void usart_enable(usart_dev *dev); + + /* From <libmaple/i2c.h> */ + void i2c_master_enable(i2c_dev *dev, uint32 flags); + +After you've initialized, and potentially enabled, your peripheral, it +is now time to begin using it. The :ref:`libmaple API pages +<libmaple-apis>` are your friends here. + +.. rubric:: Footnotes + +.. [#fgpio] As an exception, GPIO ports are given letters instead of + numbers (``GPIOA`` and ``GPIOB`` instead of ``GPIO1`` and + ``GPIO2``, etc.). |