aboutsummaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--source/hardware/maple-ret6.rst28
-rw-r--r--source/hardware/maple.rst32
2 files changed, 48 insertions, 12 deletions
diff --git a/source/hardware/maple-ret6.rst b/source/hardware/maple-ret6.rst
index 45a59cd..5fa43a8 100644
--- a/source/hardware/maple-ret6.rst
+++ b/source/hardware/maple-ret6.rst
@@ -13,22 +13,27 @@ Technical Specifications
* MCU: **STM32F103RET6**, a 32-bit ARM Cortex M3 microprocessor
* Clock Speed: **72 MHz**
- * Operating Voltage: 3.3V
- * Input Voltage (recommended): 3V-12V
+ * **512KB Flash** and **64KB SRAM**
* 44 Digital I/O Pins (:ref:`GPIO <gpio>`)
* 16 Analog Input pins, 12 bit **ADC** resolution (:ref:`ADC <adc>`)
+ * Built-in, 2 channel **DAC** at 12 bit resolution
+ (:ref:`libmaple-dac`).
* 19 **PWM** pins at 16-bit resolution (:ref:`PWM <pwm>`)
* Dedicated **USB** port for programming and communications (:ref:`USB<usb>`)
* External **JTAG** interface (:ref:`JTAG <jtag>`)
- * **512KB Flash** and **64KB SRAM**
- * 64 Channel nested vector interrupt handler (including external interrupt on GPIOs)
+ * 64 Channel nested vector interrupt handler (including
+ :ref:`external interrupt <lang-attachinterrupt>` on GPIOs)
* Integrated **SPI** (:ref:`SPI <spi>`)
+ * Integrated **SDIO**
* Integrated **I2C** and **I2S** (:ref:`I2C <i2c>`)
- * 12 Channels of Direct Memory Access (**DMA**)
+ * 12 Channels of Direct Memory Access (**DMA**) (:ref:`libmaple-dma`)
* 3 **USART** and 2 **UART** devices (:ref:`USART <usart>`)
- * Six 4-channel and two basic **timers** (:ref:`Timers <timers>`)
+ * Two advanced control, four general purpose, two basic **timers**
+ (:ref:`timers`)
* Supplies up to 800mA @ 3.3v
* Support for low power and sleep modes (<500uA)
+ * Operating Voltage: 3.3V
+ * Input Voltage (recommended): 3V-12V
* Dimensions are 2.05″x2.1″
.. _maple-ret6-powering:
@@ -256,12 +261,21 @@ Errata
This section lists known issues and warnings for the Maple RET6 Edition.
-* **DAC, UART4, UART5 GPIOs unavailable**: Pins related to the digital
+* **UART4, UART5 GPIOs unavailable**: Pins related to the digital
to analog converter (DAC) and UARTs 4 and 5 are not broken out to
headers. The RET6 Edition's hardware layout is identical to that of
the Maple Rev 5, which wasn't designed for use with these
STM32F103RET6-only peripherals.
+* **DAC channel 2 on BOARD_LED_PIN**: The Maple Rev 5 connects PA5 to
+ the board's built-in LED; this is the same GPIO bit which is
+ connected to the DAC's channel 2 output.
+
+* **Reset and NJTRST tied together**: The MCU's reset pin is tied to
+ PB4, the NJTRST (JTAG reset) pin, which is pin 43. Thus, attempting
+ to use pin 43 as a GPIO will reset your board (and also prevents the
+ JTAG "reset halt" command from working properly).
+
Recommended Reading
-------------------
diff --git a/source/hardware/maple.rst b/source/hardware/maple.rst
index 87878e9..4616ac7 100644
--- a/source/hardware/maple.rst
+++ b/source/hardware/maple.rst
@@ -13,22 +13,23 @@ Technical Specifications
* MCU: **STM32F103RBT6**, a 32-bit ARM Cortex M3 microprocessor
* Clock Speed: **72 MHz**
- * Operating Voltage: 3.3V
- * Input Voltage (recommended): 3V-12V
+ * **128KB Flash** and **20KB SRAM**
* 44 Digital I/O Pins (:ref:`GPIO <gpio>`)
* 16 Analog Input Pins, 12-bit **ADC** resolution (:ref:`ADC <adc>`)
* 15 **PWM** pins at 16-bit resolution (:ref:`PWM <pwm>`)
* Dedicated **USB** port for programming and communications (:ref:`USB <usb>`)
* External **JTAG** interface (:ref:`JTAG <jtag>`)
- * **128KB Flash** and **20KB SRAM**
- * 64 Channel nested vector interrupt handler (including external interrupt on GPIOs)
+ * 64 Channel nested vector interrupt handler (including
+ :ref:`external interrupt <lang-attachinterrupt>` on GPIOs)
* Integrated **SPI** (:ref:`SPI <spi>`)
* Integrated **I2C** (:ref:`I2C <i2c>`)
- * 7 Channels of Direct Memory Access (**DMA**)
+ * 7 Channels of Direct Memory Access (**DMA**) (:ref:`libmaple.dma`)
* 3 **USART** divices (:ref:`USART <usart>`)
* Four 4-channel **timers** (:ref:`Timers <timers>`)
* Supplies up to 800mA @ 3.3v
* Support for low power and sleep modes (<500uA)
+ * Operating Voltage: 3.3V
+ * Input Voltage (recommended): 3V-12V
* Dimensions are 2.05″x2.1″
.. _maple-identify-rev:
@@ -307,6 +308,13 @@ Rev 5
from its silkscreen. This mistake was fixed in later manufacturing
runs.
+* **Reset and NJTRST tied together**: The MCU's reset pin is tied to
+ PB4, the NJTRST pin, which is pin 43. Thus, attempting to use pin
+ 43 as a GPIO will reset your board (and also prevents the JTAG
+ "reset halt") command from working properly. It's possible to cut
+ the trace, but doing so will damage your board, so we *do not
+ recommend it* unless you're very sure about what you're doing.
+
Rev 3
^^^^^
@@ -352,6 +360,13 @@ Rev 3
* **PWM Marketing Mistake**: We originally sold the Maple advertising
22 channels of 16-bit hardware PWM; actually the Maple only has 15.
+* **Reset and NJTRST tied together**: The MCU's reset pin is tied to
+ PB4, the NJTRST pin, which is pin 43. Thus, attempting to use pin
+ 43 as a GPIO will reset your board (and also prevents the JTAG
+ "reset halt") command from working properly. It's possible to cut
+ the trace, but doing so will damage your board, so we *do not
+ recommend it* unless you're very sure about what you're doing.
+
Rev 1
^^^^^
@@ -386,6 +401,13 @@ Rev 1
* **PWM Marketing Mistake**: We originally sold the Maple advertising
22 channels of 16-bit hardware PWM; the correct number is 15.
+* **Reset and NJTRST tied together**: The MCU's reset pin is tied to
+ PB4, the NJTRST pin, which is pin 43. Thus, attempting to use pin
+ 43 as a GPIO will reset your board (and also prevents the JTAG
+ "reset halt") command from working properly. It's possible to cut
+ the trace, but doing so will damage your board, so we *do not
+ recommend it* unless you're very sure about what you're doing.
+
Recommended Reading
-------------------