aboutsummaryrefslogtreecommitdiffstats
path: root/docs/source/hardware
diff options
context:
space:
mode:
authorMarti Bolivar <mbolivar@leaflabs.com>2011-05-13 17:44:46 -0400
committerMarti Bolivar <mbolivar@leaflabs.com>2011-05-13 20:10:37 -0400
commit03ad1753053f6fc8a46d88bf20c6690619e1d54d (patch)
treeb6a447df70e3d6c1a2091860ec440baeb96e9a8d /docs/source/hardware
parent2b5547a2adfdb5c8c6d7a61b03f0fa81c336d046 (diff)
downloadlibrambutan-03ad1753053f6fc8a46d88bf20c6690619e1d54d.tar.gz
librambutan-03ad1753053f6fc8a46d88bf20c6690619e1d54d.zip
Docs: Removing note about cutting the Maple's NJTRST<->NRST trace.
Worried about the possibility of an attractive nuisance.
Diffstat (limited to 'docs/source/hardware')
-rw-r--r--docs/source/hardware/maple-ret6.rst8
-rw-r--r--docs/source/hardware/maple.rst10
2 files changed, 8 insertions, 10 deletions
diff --git a/docs/source/hardware/maple-ret6.rst b/docs/source/hardware/maple-ret6.rst
index 1f3a656..d6a7c0e 100644
--- a/docs/source/hardware/maple-ret6.rst
+++ b/docs/source/hardware/maple-ret6.rst
@@ -279,10 +279,10 @@ This section lists known issues and warnings for the Maple RET6 Edition.
the board's built-in LED; this is the same GPIO bit which is
connected to the DAC's channel 2 output.
-* **Reset and NJTRST tied together**: The MCU's reset pin is tied to
- PB4, the NJTRST (JTAG reset) pin, which is pin 43. Thus, attempting
- to use pin 43 as a GPIO will reset your board (and also prevents the
- JTAG "reset halt" command from working properly).
+* **Reset and NJTRST tied together**: The MCU's reset pin is connected
+ to PB4, the NJTRST (JTAG reset) pin, which is pin 43. Thus,
+ attempting to use pin 43 as a GPIO will reset your board (and also
+ prevents the JTAG "reset halt" command from working properly).
Recommended Reading
-------------------
diff --git a/docs/source/hardware/maple.rst b/docs/source/hardware/maple.rst
index 2ae1c30..d0434ab 100644
--- a/docs/source/hardware/maple.rst
+++ b/docs/source/hardware/maple.rst
@@ -322,12 +322,10 @@ Rev 5
from its silkscreen. This mistake was fixed in later manufacturing
runs.
-* **Reset and NJTRST tied together**: The MCU's reset pin is tied to
- PB4, the NJTRST pin, which is pin 43. Thus, attempting to use pin
- 43 as a GPIO will reset your board (and also prevents the JTAG
- "reset halt") command from working properly. It's possible to cut
- the trace, but doing so will damage your board, so we *do not
- recommend it* unless you're very sure about what you're doing.
+* **Reset and NJTRST tied together**: The MCU's reset pin is connected
+ to PB4, the NJTRST pin, which is pin 43. Thus, attempting to use
+ pin 43 as a GPIO will reset your board (and also prevents the JTAG
+ "reset halt") command from working properly.
Rev 3
~~~~~