diff options
Diffstat (limited to 'target/device/Atmel/arch-avr32/kernel-patches-2.6.22.10/linux-2.6.22.10-500-gpio_mouse-setup-for-atstk1000-board.patch')
| -rw-r--r-- | target/device/Atmel/arch-avr32/kernel-patches-2.6.22.10/linux-2.6.22.10-500-gpio_mouse-setup-for-atstk1000-board.patch | 130 |
1 files changed, 0 insertions, 130 deletions
diff --git a/target/device/Atmel/arch-avr32/kernel-patches-2.6.22.10/linux-2.6.22.10-500-gpio_mouse-setup-for-atstk1000-board.patch b/target/device/Atmel/arch-avr32/kernel-patches-2.6.22.10/linux-2.6.22.10-500-gpio_mouse-setup-for-atstk1000-board.patch deleted file mode 100644 index 330f9e0c4..000000000 --- a/target/device/Atmel/arch-avr32/kernel-patches-2.6.22.10/linux-2.6.22.10-500-gpio_mouse-setup-for-atstk1000-board.patch +++ /dev/null @@ -1,130 +0,0 @@ ->From 9c5fa914202d20756c56e0c4fd76035ed8f8ced8 Mon Sep 17 00:00:00 2001 -From: Hans-Christian Egtvedt <hcegtvedt@atmel.com> -Date: Mon, 6 Aug 2007 08:31:14 +0200 -Subject: [PATCH 1/1] Add gpio_mouse board setup to atstk1000 board - -This patch adds a gpio_mouse_platform_data to the atstk1000 board code and -registers a gpio_mouse platform_device. This will enable a GPIO mouse on header -J1 on GPIO of the ATSTK1000 development kit. The board code is enabled/disabled -in menuconfig. - -By connecting J1 (GPIO) to J25 (SWITCH) you can use the following keys to -simulate a mouse: - -SW0: right -SW1: down -SW2: up -SW3: left -SW5: right button -SW6: middle button -SW7: left button - -Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com> ---- - arch/avr32/boards/atstk1000/Kconfig | 16 ++++++++++ - arch/avr32/boards/atstk1000/atstk1002.c | 48 +++++++++++++++++++++++++++++++ - 2 files changed, 64 insertions(+), 0 deletions(-) - -diff --git a/arch/avr32/boards/atstk1000/Kconfig b/arch/avr32/boards/atstk1000/Kconfig -index 718578f..d99d4bd 100644 ---- a/arch/avr32/boards/atstk1000/Kconfig -+++ b/arch/avr32/boards/atstk1000/Kconfig -@@ -50,6 +50,22 @@ config BOARD_ATSTK1002_SPI1 - GPIO lines and accessed through the J1 jumper block. Say "y" - here to configure that SPI controller. - -+config BOARD_ATSTK1002_GPIO_MOUSE -+ bool "Configure gpio_mouse on GPIO J1 header" -+ depends on !BOARD_ATSTK1002_SW4_CUSTOM -+ help -+ Enable gpio_mouse board configuration on GPIO 0 to 7. Connecting a -+ 10-pin flat cable from J1 (GPIO) to J25 (SWITCH) will let a user give -+ mouse inputs using the the switches SW0 to SW7. -+ -+ SW0: right -+ SW1: down -+ SW2: up -+ SW3: left -+ SW5: right button -+ SW6: middle button -+ SW7: left button -+ - config BOARD_ATSTK1002_J2_LED - bool - default BOARD_ATSTK1002_J2_LED8 || BOARD_ATSTK1002_J2_RGB -diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c -index c958fd4..c7560e5 100644 ---- a/arch/avr32/boards/atstk1000/atstk1002.c -+++ b/arch/avr32/boards/atstk1000/atstk1002.c -@@ -17,6 +17,7 @@ - #include <linux/types.h> - #include <linux/spi/spi.h> - #include <linux/spi/at73c213.h> -+#include <linux/gpio_mouse.h> - - #include <video/atmel_lcdc.h> - -@@ -91,6 +92,49 @@ static struct mci_platform_data __initdata mci0_data = { - .wp_pin = GPIO_PIN_NONE, - }; - -+#ifdef CONFIG_BOARD_ATSTK1002_GPIO_MOUSE -+static struct gpio_mouse_platform_data gpio_mouse0_data = { -+ .polarity = GPIO_MOUSE_POLARITY_ACT_LOW, -+ { -+ { -+ .up = GPIO_PIN_PB(2), -+ .down = GPIO_PIN_PB(1), -+ .left = GPIO_PIN_PB(3), -+ .right = GPIO_PIN_PB(0), -+ .bleft = GPIO_PIN_PB(7), -+ .bmiddle = GPIO_PIN_PB(6), -+ .bright = GPIO_PIN_PB(5), -+ }, -+ }, -+ .scan_ms = 10, -+}; -+ -+static struct platform_device gpio_mouse0_device = { -+ .name = "gpio_mouse", -+ .id = 0, -+ .dev = { -+ .platform_data = &gpio_mouse0_data, -+ }, -+}; -+ -+static void __init add_device_gpio_mouse0(void) -+{ -+ struct platform_device *pdev = &gpio_mouse0_device; -+ struct gpio_mouse_platform_data *data = pdev->dev.platform_data; -+ -+ at32_select_gpio(data->up, 0); -+ at32_select_gpio(data->down, 0); -+ at32_select_gpio(data->left, 0); -+ at32_select_gpio(data->right, 0); -+ -+ at32_select_gpio(data->bleft, 0); -+ at32_select_gpio(data->bmiddle, 0); -+ at32_select_gpio(data->bright, 0); -+ -+ platform_device_register(pdev); -+} -+#endif -+ - /* - * The next two functions should go away as the boot loader is - * supposed to initialize the macb address registers with a valid -@@ -321,6 +365,10 @@ static int __init atstk1002_init(void) - #endif - #endif - -+#ifdef CONFIG_BOARD_ATSTK1002_GPIO_MOUSE -+ add_device_gpio_mouse0(); -+#endif -+ - return 0; - } - postcore_initcall(atstk1002_init); --- -1.5.2.3 - |