1 files changed, 0 insertions, 81 deletions
diff --git a/package/udev/init-udev b/package/udev/init-udev
deleted file mode 100755
index 220fbcef6..000000000
--- a/package/udev/init-udev
+++ /dev/null
@@ -1,81 +0,0 @@
-#!/bin/sh
-#
-# udev	This is a minimal non-LSB version of a UDEV startup script.  It
-#	was derived by stripping down the udev-058 LSB version for use
-#	with buildroot on embedded hardware using Linux 2.6.12+ kernels.
-#
-#	You may need to customize this for your system's resource limits
-#	(including startup time!) and administration.  For example, if
-#	your early userspace has a custom initramfs or initrd you might
-#	need /dev much earlier; or without hotpluggable busses (like USB,
-#	PCMCIA, MMC/SD, and so on) your /dev might be static after boot.
-#
-#	This script assumes your system boots right into the eventual root
-#	filesystem, and that init runs this udev script before any programs
-#	needing more device nodes than the bare-bones set -- /dev/console,
-#	/dev/zero, /dev/null -- that's needed to boot and run this script.
-#
-
-# old kernels don't use udev
-case $(uname -r) in
-    2.6*|2.7*)	;;
-    *)		exit 0;;
-esac
-
-# Check for missing binaries
-UDEV_BIN=/sbin/udevd
-test -x $UDEV_BIN || exit 5
-UDEVSTART_BIN=/sbin/udevstart
-test -x $UDEVSTART_BIN || exit 5
-
-# Check for config file and read it
-UDEV_CONFIG=/etc/udev/udev.conf
-test -r $UDEV_CONFIG || exit 6
-. $UDEV_CONFIG
-
-# Directory where sysfs is mounted
-SYSFS_DIR=/sys
-
-case "$1" in
-    start)
-        # mount sysfs if it's not yet mounted
-        if [ ! -d $SYSFS_DIR ]; then
-	    echo "${0}: SYSFS_DIR \"$SYSFS_DIR\" not found"
-	    exit 1
-        fi
-        grep -q "^sysfs $SYSFS_DIR" /proc/mounts ||
-	mount -t sysfs /sys /sys ||
-	exit 1
-
-        # mount $udev_root as ramfs if it's not yet mounted
-        # we know 2.6 kernels always support ramfs
-        if [ ! -d $udev_root ]; then
-	    echo "${0}: udev_root \"$udev_root\" not found"
-	    exit 1
-        fi
-        grep -q "^udev $udev_root" /proc/mounts ||
-	mount -t ramfs udev $udev_root ||
-	exit 1
-
-        mkdir $udev_root/pts $udev_root/shm
-
-        # populate /dev (normally)
-        echo -n "Populating $udev_root using udev: "
-        echo -e '\000\000\000\000' > /proc/sys/kernel/hotplug
-        $UDEV_BIN -d || (echo "FAIL" && exit 1)
-	$UDEVSTART_BIN || (echo "FAIL" && exit 1)
-        echo "done"
-        ;;
-    stop)
-        # Stop execution of events
-        udevcontrol stop_exec_queue
-        killall udevd
-        ;;
-    *)
-        echo "Usage: $0 {start|stop}"
-        exit 1
-        ;;
-esac
-
-
-exit 0